Ahmad Daniel Email & Phone Number

1.To perform visual inspection on 19 unit of tank farm to check metal lost, corrosion, leakage, coating condition, piping condition.2.Remarks all finding in visual inspection report and submit to client.

1.Prepare ITP2.Prepare and monitor in house inspection checklist.3.Check material received specification as per mill cert and API and PTS standard.4.Check consumable specification as per code API 1104 and PTS.5.Prepare Pre-WPS for welding for test piece using combination welding GTAW & SMAW as per API 1104, API RP 1107, PTS 15.12.04 & PTS 12.30.07.6.Witness PQR for test coupon.7.Review NDT report (MPI and UT) as per Acceptance criteria from API 1104 and ensure report follow NDT procedure.8.Verifying all materials and consumables prior to fit-up and welding.9.Monitor welder and advice them to follow current and temperature as per WPS.10.Carrying out visual inspection and final inspection with third party and client representative before NDT.11.Witnessing mechanical test at lab follow API 1104 and PTS.12.WPS endorsement with third party, IWE(International Welding Engineer) and client representative.13.Arrange all NDT and third party at site.14.Monitor fit-up distance band.15.Monitor hot tap welding on site. 16.Carrying out visual inspection with third party and client representative.17.Witnessing NDT after 48 hours with third party and client representative.18.Write out fit-up and visual report based on visual inspection.19.Witnessing pressure test after complete NDT.20.Witnessing sub-contractor install stopaq follow all requirement from PTS and being test with Holiday Test to check if there are any bubble air that trap inside.21.Provided client on-site consulting about regarding welding issue and technical issue.22.Demonstrated ability to work remotely with minimal supervision while effectively managing time accommodate extensive travel and associated scheduling.23.Educated,updated and discuss clients on procedural,technological,compliance and regulatory changes affecting workflow,pricing, technology, and service.

1. Perform site visit and project cost estimation and submit to PGB.2. Prepare all related document (ERP, organization chart, MOS, project schedule and etc).3. Prepare for project execution plan and project flow.4. Attend pre-job meeting with client to approved all related document and project schedule.5. Monitor project execution and liase with client.6. Record daily activity.7. Inspect pipe coating condition with client representative.8. Calculate metal lost percentage.9. Draw metal lost on the tracing paper for record.10. Discuss with client representative method to repair coating.11. Witnessing repair method install by sub-contractor.12. Witnessing Holiday test after complete repair.13. Write out Holiday test report. 14. Fill ISO repair form and attach in the final document.15. Prepare final report.16. Attend commercial meeting with client.17. Prepair project claim.

QA/QC ENGINEER1. Prepare ITP2. Prepare and monitor in house inspection checklist.3. Check material received specification as per mill cert and API and PTS standard.4. Check consumable specification as per code API 1104 and PTS.5. Prepare Pre-WPS and Pre- WPS repair for Epoxy welded sleeve for pipe 18“ and 30“ size using combination welding GTAW & SMAW as per API 1104, API RP 1107, PTS 15.12.04 & PTS 12.30.07.6. Witness PQR for test coupon.7. Review NDT report (MPI and UT) as per Acceptance criteria from API 1104 and ensure report follow NDT procedure.8. Verifying all materials and consumabes prior to fit-up and welding.9. Monitor welder and advice them to follow current and temperature as per WPS.10. Carrying out visual inspection and final inspection with third party and client representative before NDT.11. Witnessing mechanical test at lab follow API 1104 and PTS.12. WPS endorsement with third party, IWE(International Welding Engineer) and client representative.13. Arrange all NDT and third party at site.14. Monitor fit-up distance band.15. Monitor hot tap welding on site. 16. Carrying out visual inspection with third party and client representative.17. Witnessing NDT after 48 hours with third party and client representative.18. Write out fit-up and visual report based on visual inspection.19. Witnessing pressure test after complete NDT.20. Witnessing sub-contractor install stopaq follow all requirement from PTS and being test with Holiday Test to check if there are any bubble air that trap inside.

1. Perform site visit and project cost estimation and submit to PGB.2. Prepare all related document (ERP, organization chart, MOS, project schedule and etc).3. Prepare for project execution plan and project flow.4. Attend pre-job meeting with client to approved all related document and project schedule.5. Monitor project execution and liase with client.6. Record daily activity.7. Inspect pipe coating condition with client representative.8. Calculate metal lost percentage.9. Draw metal lost on the tracing paper for record.10. Discuss with client representative method to repair coating.11. Witnessing repair method install by sub-contractor.12. Witnessing Holiday test after complete repair.13. Write out Holiday test report. 14. Fill ISO repair form and attach in the final document.15. Prepare final report.16. Attend commercial meeting with client.17. Prepair project claim.

1.Performed inspection which includes material inspection, fit-up inspection, welding inspection and visual inspection.2.Document reviewed which include Inspection summary report, NDT reports reviewed, validation of calibration certificates and actual welding parameter records.

Kemaman Terengganu

1. Arrange manpower to complete every task from manager.2. Conduct weekly meeting between technician and to update weekly progress.3. Inspected received material from its specification, quality,quantity by referring to the mills certificate.4. Conduct Hydro test based on API 6D before sent to client.5. Advices the company to write a new work procedure follow all requirements from client and any related code and standard practices.6. Prepared a valve service and inspection report.7. Liaise with client to come and witness the hydro test if the pre-test have done successful without leaking on the valve.8. Prepared final documentation that to be submitting to the client.9. Examine the product has been packed in the best quality and condition before delivered to clients.

Epcc Tebong City Gate,Onshore Slug Catcher(Osc)

1. Inspect received material from its specification, quality, and quantity by referring to the mills certificate.2. Inspect fit-up for hot tapping.3. Record all data about welding.4. Visual inspection of weldments from any visible defect that comply with Clients/code of standard acceptance criteria.5. Request and arrange for non-destructive testing with third party (DPT, MPI, RT, UT) if required for completed weld joint.6. Prepare for the final documentation that to be submit to the client.

Kemaman, Terengganu

1. Monitor and inspection of drill pipe, BHA (bottom hole assembly) and lifting based on code and standard specification requirements (TH Hill).2. Update daily inspection non-destructive testing report3. Witness and attend the hydro test.4. Assist level II inspector and skill helper in drill pipe, bottom hole assembly and lifting department.5. Assist QA/QC administrator.6. Documented an inspection report for client.