Alfred Ray Email and Phone Number

• Responsible for calibrating all manual and automated calibration of electronic equipment Vibration Controller VR8500, VR9500,SR620. DS345,DS340.• Set up repair request for equipment that failed calibration• Kept track of all customer equipment sent out for repair and calibration • Run automation calibration software,Met/Cal. Preform manual calibration on electrical equipment.Verify all failures too see if the unit under test was actually failed at the test points.Received Met /Cal Procedure Development Certificate

• Certified and set up calibration lab• Responsible for calibrating all electronic equipment • Set up repair request for equipment that failed calibration• Kept track of all customer equipment sent out for repair and calibration • Ran automation calibration software, STE, TME3, Met/Cal.

Contract• Responsible for the repair of customers’ overhead projectors• Updated company’s loaners, tests, and other electronic equipment • Performed prescheduled firmware and software updates• Provided exceptional customer service to internal and external customers, staff, and vendors

ContractResponsible for testing all wires connects and electronics , electrical equipment on all Trains coming out of the production line along with verifying that and upload firmware and software onto the train computer mainframe

Contract• Responsible for testing all wires connects and electronics, electrical equipment on all trains coming out of the production line • Verified and uploaded firmware and software onto the train computer mainframe• Worked as a team member in achieving seamless work performance between departments and units

Contract• Responsible for calibrating Agilent Signal Generators, X Series Generators (MXG, ESG), PSG Signal Generators, ran manual/automation TME, STE Program IOS calibration to Manufacturing and National standards.

Contract• Responsible for calibration and repair of Analyzer models ESA and PSA and upgrade firmware and operating software. ESA and PSA that I calibrated Spectrum Analyzer model numbers E44001B, E4403B, E4404B, E4405B, E4407B, E4408, E7401A problem solving and root cause analysis techniques to troubleshoot electronics based products issues to component level using standard test equipment (computers, oscilloscope, analyzer, digital multi-meter)

Contract• Responsible for software installing in the EXT 6607A• Completing pre calibration and calibration of yellow stone in manufacturing. • Pretest PXA3 boards Ref board, LO ref board, Digital Analog Dif40, Analog Dif40.• Troubleshot and repaired front-end control boards for the PXA3 production line.

Contract• Responsible for calibration and repair of ESA and PSA as well as document all work and repairs. • Documented information for the calibrations of ESA and PSA (E44001B, E4403B, E4404B, E4405B, E4407B, E4408, E7401A).

ContractResponsible for calibration and repair of 67XX and 506X and upgrades document all work and repairs. 506X and 67XXthat problem solving and root cause analysis techniques to troubleshoot electronics based products issues to component level through analysis of digital and analog circuits using standard test equipment (oscilloscope, network analyzer, digital multi-meter

Responsible for repair and or replace PLC's and frequency drives was involve in modifying, rebuilding, or overhauling equipment to meet company sandards and upgraded needed. Manufacturing equipment that was not in used perform PM and or repair. Write equipment maintenance specifications. Proactively monitor equipment performance and work towards resolving problems permanently through upgrades, preventive and/or corrective maintenance. Follow up with supervisors, Engineers, on technical issues relating to equipment maintenance. Troubleshooting of electronics system to determine cause and remedy for malfunctions.

Prepare root cause failure analyses and recommendations for corrective Perform reliable testing and try to re duplicate failure in with the customer sent the equipment in for. Write tests summary reports for failure for Crane controls.

Close Down) Program Robotic Arm, mix chemical for T.V tubes and document all break downs, shut downs. And supervise 25 to 50 employee's make sure that they was doing there work and assign them to other work if the machine when down.

ContractResponsible for installation, test, repair and maintenance of computer modem using diagrams and schematics, and applying knowledge of digital and analog circuitry and functions to meet company specifications.. Perform equipment maintenance on a periodic test equipment.

Analysis and repair of Two-way radios using the following types of equipment: RF generator, oscilloscope, service monitor, dc power supply, frequency counter, ac meter, and pace station. Experiences includes trouble-shooting and repair to the component level- analog,digital, microprocessor and op-amp circuits. Check assemblies, calibrate and troubleshoot electronic circuit boards. Checks assembly and tests power supply assemblies. Provides customer service bytelephone, as required

Analysis and repair of pagers and cellular phones using the following types of equipment: RF generator, oscilloscope, service monitor, dc power supply, frequency counters meter, and pace station,experiences include trouble-shooting and repair to the component level. And order all stock for all 6 stores and travel to all stores and check the work of all the Technicians