Create solution using location intelligence toolsCreate presentation for solution design (Topology, hardware design, automation process, benefit and waste elimination, ROI projection)RTLS plannerDesign and create concept developmentSupervision Deployment team

open freelance job for programming and commisioning PLC, HMI, and SCADA1. Programming and Commisioning PLC Siemens S7 1200 and HMI Siemens for Aeration and Hammer System in PT Indocement Cirebon

Automation and IOTProject:OEE system upgrade for PT. Syngenta (plant Gunung Putri) (-) Install photo sensor for counter product(-) Configuration module wireless remote IO (WF-2051) (-) Configuration communication modbus TCP/IP module remote IO to Node RedProject:Manufacturing 4.0 for PT. Electra Mobilitas Indonesia (plant Cikarang)Andon System and OEE(-) Programming PLC and HMI using FX5UJ Mitsubishi and GS2107 Mitsubishi (GXWorks3 and GT Designer 3). (-) Communicate PLC to HMI and Server (Node-Red) using Modbus TCP/IP (-) Communicate PLC to Drive (Inverter MX2 Omron) using Modbus RTU Serial (-) Setting VNC Server of HMI for remote access to monitor control room and android (-) Making BOM (-) Document Engineer (IO List, Wiring Electrical Diagram, System Architecture) (-) Execution on PLC Panel (Wiring Electrical)(-) SAT and trainer Energy Monitoring(-) Setting gateway (USR-TCP-410s) for access from Power Meter PM2100 (serial) to gateway (TCP/IP) (-) Communicate gateway to server (Node-Red) (-) Design and concept for energy monitoring gateway(-) Supporting for query data in database (Influx DB)Project:HSSD Panel for Pertamina Hulu Sanga Sanga - Samberah Plant 14(-) Add tag/address for alarm (fire1) and fault (power fault) HSSD Panel to Scada wonderware and Panelview 1250(-) Commissioning and test HSSD PanelProject:FGS C-1050 Panel (PHSS Mutiara Plant) (-) Terminasi Kabel Control untuk field device(-) Editing Revision Program(-) CommisioningProject:Internal Project: Smart Face Recognition Employee Absent(-) Integrated Hikivision face Recognition to Node-Red using API protocol(-) Integrated Node-Red to Coda.io using API with webhook automation systemProject:Ilobby PT Syngenta (Gunung Putri)(-) Create IOT Panel (assembly, wiring electrical)(-) Programming Arduino IDE for RFID Reader wiegand 26bit(-) Programming Node Red DAQ

"Upgrade System Control" - Pertamina Hulu Kalimantan Timur (PHKT) On Sepinggan and Yakin.Survey Site; Finishing Document Engineering (General Arrangment, Wiring Electrical Diagram, Bill of Material, IO List, Logic Diagram, etc); FAT Test; etc"Secondary Clarifier" - PT. Tjiwi Kimia MojokertoI am as leader or coordinator in this projectFinishing Document Engineering (Wiring Diagram for PLC Panel start from power control, marshalling, making IO List, etc)Finishing PLC panel (assemblying part like duct, din rail, wiring diagram)Finishing test and commisioning in Factory Acceptance Test with customer (Logic Test, Sequence Test, Visic Chechk)Finishing PLC program using TIA Portal Step 7 V17, SCADA using Wincc Proffesional V.15 with 128 tag.

"Pembangunan Terminal LPG Pneurize Pertamina Tenau Kupang" - Pertamina KupangFinishing Document Engineering (Wiring Diagram, IO List Tag PLC, General Arrangment Panel); Supported for designing HMI using FTView and DCS using PlanPax; Execution Panel; Support FAT Test."Fire and Gas Detector System A and B" Pertamina PlajuExecution Panel (Wiring Electrical, etc until panel ready for used) ; Setting Redudancy Module for Controllogix Controller, Setting Modbus module (Prosoft); Support in FAT Test (Logic test, Cause and Effect Test, redundant test), etc

1. Completing project of revision ROBLON T300 machine as PLC, HMI and wiring intallation panelProgramming PLC using Panasonic FP0R, the application for created program is FPWIN GR (old version)Programming HMI using Weintek MT version 5inc2. Completing project of revision ROBLON M55 / 30 machine as PLC, HMI, and VSD programmer and wiring intallation panel.Programming PLC using Panasonic FP0R, the application for created program is FPWIN GR (old version)Programming HMI using Weintek MT version 7incSetting Inverter using TECO Drive Type A510s3. Completing project of revision ROBLON M33 / 8 machine as PLC, HMI, and VSD programmer and wiring intallation panelProgramming PLC using Panasonic FP0R, the application for created program is FPWIN GR (old version)Programming HMI using Weintek MT version 7incSetting Inverter using Lenze Drive4. Completing of revision lathe machine (TURNER Machine) as wiring installation5. Completing project of revision ROBLON M55 / 15 machine as PLC, HMI, and VSD programmer and wiring intallation panel6. Making safety system for yarn break on ROBLON machines (PLC Program)7. Completing project of revision ROBLON M44 / 20 as PLC, HMI, and VSD programmer and wiring intallation panelProgramming PLC using Panasonic FP0R, the application for created program is FPWIN GR (old version)Programming HMI using Weintek MT version 7incSetting Inverter using TECO Drive Type A510s

Berpengalaman dalam kerja praktek di PT. PERTAMINA (PERSERO) TBBM SEMARANG GROUP. Kerja praktek dilaksanakan mulai bulan Januari 2019 - Februari 2019. Judul projek yang diambil selama pelaksanaan kerja praktek adalah desain piping and instrument diagram PT. PERTAMINA (PERSERO) TBBM SEMARANG GROUP.