Zotye-Ford JV new BEV plant Build1.Working with EPC to Develop the bodyshop layout /finalize the size /column pitch,hight/roof loading constrain.design the logistic path,raise the requirement on ground floor / water /air /electric power.2.Define the column map and the layout of the transfer system in the air which include pallet system within body shop production line and the skid line which flow to paint shop.define the loading point and unloading point.3.Provide the eject smoke… Show more Zotye-Ford JV new BEV plant Build1.Working with EPC to Develop the bodyshop layout /finalize the size /column pitch,hight/roof loading constrain.design the logistic path,raise the requirement on ground floor / water /air /electric power.2.Define the column map and the layout of the transfer system in the air which include pallet system within body shop production line and the skid line which flow to paint shop.define the loading point and unloading point.3.Provide the eject smoke requirement and layout, also take care of the metal finish line requirement.4.Develop the organization chart and make recruiting plan for open positions5.Process analysis on weld distribution /cycle time.6.Make sure all the RFQ and technical requirement been completed especially Long lead facility (hemming press/crane) been captured.7.Raise the budget requirement and make sure all is within control. Visit supplier side for candidate supplier evaluation and technical proposal discussion.8.Timing plan development according to construction status.9.Working with quality team and finalize the quality target for bodyshop measurement . Show less

The responsibilities are to ensure product can be manufactured in the relevant location within budget F&T, on time and meet the quality targets from initial concept into full production,Ensure new product follow the correct process and ensure all forward planning tools are applied correctly including DPA5(Digtal Pre-Assembly) .These include:1.Work cross functions(especially PD) in design team mode to deliver manufacturing feasible design.2.Virtual build events( tooling/fixture… Show more The responsibilities are to ensure product can be manufactured in the relevant location within budget F&T, on time and meet the quality targets from initial concept into full production,Ensure new product follow the correct process and ensure all forward planning tools are applied correctly including DPA5(Digtal Pre-Assembly) .These include:1.Work cross functions(especially PD) in design team mode to deliver manufacturing feasible design.2.Virtual build events( tooling/fixture design and production line simulation) to ensure the products can be assembled smoothly.3.Develop inspection poins by working with Meterology.Develop GD&T and Locator strategy for assembly parts and single parts.4.Create and Maintenance FMEA and develop plant control plan with control methods with Dimensional improvement plants.5. Facility&tooling budget is captured and balanced to support launch and sign off process.6.Develop the Process/Facility/Layout of the production line7. Complete the purchasing activity include Weld gun/ Robot /tooling to support all launch activity.8.Develop the RFQ and support document. Lead the evaluation activity on the suppliers to make sure all the bidding activities meet the target on quality,cost and timing.9.Lead Supplier Process review and 3D tooling design review(25%/50%/100%).10.The Pprototype build activity on site.11. Lead the Facility installation,commissioning and ramp of mass volume roduction lines.12.Make sure all the launch activities follow the right timing. And all the open issue (tooling design/LD/availability/safety/ergo/control/Robot programming/PLC programming/FMEA.. )closed before buyoff .13.Quality improvement during launch phase, In charge of PCF slow build activities.Make sure Pist/PP/Ppk meet the target requirement of each stage14. Report the OKTB Score Card status to the AP Management.15. Consolidate the Lesson learned which include advanced stage and launch phase to make sure that can be followed by next project. Show less

Ford Product Fiesta is launched in ChangAn Ford Plant.As body Rep responsible for quality solving activities during launch activity.Working with Ford Europe D&R center, evaluation the engineer changes.Report the quality issues to the Ap body Management.

Responsible for engineering changes events of muti-functions for Ford Kugu Product.

Support the Black belt program which is to help the production company to solve quality issues.Using Control tools and SW Minitab to analize the potential risk and control consultant.(DMAIC/8D)

Responsible for TiNA Engine assembly line cycle time and Materail logistic optimization.(eplant/flexsim)