Mohamed El Liethy, Pmp Email & Phone Number

Egypt

Achievement1- Raw Material Burnability Developing Project Aim To Decrease SHC.2- Ceramic Waste Clay Replacement Project Aim To Decrease SHC & CO2 Emission.3- Alternative Fuel Project With SINOMA CDI.4- Performance, GAP, SHC, SPC, WDT Plant Analysis System.5- Total Electrical Power Management Project.6- Pyro-Process Audit System.7- Grinding Process Audit System.8- Fuel Management & Audit System.9- Thermal Imaging & Thermal Radiation Audit System.10-… Show more Achievement1- Raw Material Burnability Developing Project Aim To Decrease SHC.2- Ceramic Waste Clay Replacement Project Aim To Decrease SHC & CO2 Emission.3- Alternative Fuel Project With SINOMA CDI.4- Performance, GAP, SHC, SPC, WDT Plant Analysis System.5- Total Electrical Power Management Project.6- Pyro-Process Audit System.7- Grinding Process Audit System.8- Fuel Management & Audit System.9- Thermal Imaging & Thermal Radiation Audit System.10- Grindability Development For OK Mills Project.11- Main Buner Measurements, Calculations, Audit System.12- False Air Analysis & Development Project.13- Technical Training Project.14- CF Silo Audit & Performance Enhancing Job Description1- Undergo Improvements In Production Processes For Better Cost Optimization.2- Prioritize Critical Process Needs With Preventive Maintenance Department To Be Achieved During PM Stoppages.3- Operation Optimization For PYRO & GRINDING Processes.4- Initiate Performance Enhancing Projects In Plant.5- Training Technical Stuff.6- Standard Operation Parameters Assembly.7- Inspection, Troubleshooting & Optimization Of Running Processes.8- On Site Process Measurements & Process Calculations.9- Monitor & Control SHC. SPC, Rawmix Design Changes & Operation Strategy.10- Daily Operation Performance Reporting.11- Monthly, Quarter, Annual Plant Performance Reports Set.12- Setting Up Plant KPIs With Top Management.13- Undergo Regular Cost Analysis For Operation Cost Efficiency & Performance.14- Coordinate & Collaborate With HSE & Q Department.15- Undergo Process Audits For PYRO & Grinding Processes.Process Audit Arabian Cement Company, EG, FLSmidth Design.Process Audit Sinai White Cement Company, EG, FLSmidth Design Process Audit Al Menya Cement Company, EG, FLSmidth Design.Process Audit Qena Cement Company, EG FLSmidth Design.Technical Training Project For El Sewedy Cement Company.Douflex Burner Audit FLSmidth.Unitherm Burner Audit UNITHERM. Show less

Egypt, Middle East

Under the production manager supervision, from the raw mix preparation to the cement silos, ensure the good functioning of the production processes According to quality and production objectives.1- Applying Safety & Health measures during routine and critical jobs during the shift fulfill all the permits required. 2- Adapt the production planning. 3- Coordinate all interventions in case of breakdown. 4- Supervise the dispatch foreman. 5- Take over & Guide the control of kiln… Show more Under the production manager supervision, from the raw mix preparation to the cement silos, ensure the good functioning of the production processes According to quality and production objectives.1- Applying Safety & Health measures during routine and critical jobs during the shift fulfill all the permits required. 2- Adapt the production planning. 3- Coordinate all interventions in case of breakdown. 4- Supervise the dispatch foreman. 5- Take over & Guide the control of kiln and mill in case of complicated situation. 6- Guarantee SHC & SPC Targeted Ranges. 7- Ensure proper use of the equipment in particular to avoid damage. 8- Ensure reports are properly filled out: daily, shift, Computer based incident analysis. 9- Organize the tasks of the maintenance crew on shift to the shift situation. 10- Insure Quality Control Aspects In Cooperation With The Quality Laboratory.11- Communicate & Cascade To on-duty manager in case of Urgent need. 12- Collaborate with Quarry & Process Department In Case Of Need. Show less

Cairo, Egypt

1- Leading the operation team and technicians so as to optimize the work procedure and the operation concepts and increase their awareness so as to optimize the process to the most safe and efficient model with the maximum production.2- Coaching team for the operation of PHC kiln 5200 tpd KHD design - FLSmidth design upgraded during and after commissioning and a VRM with a capacity of 430 tph.3- I have led a suggestion to assemble a pilot burner at the tertiary air duct so as to… Show more 1- Leading the operation team and technicians so as to optimize the work procedure and the operation concepts and increase their awareness so as to optimize the process to the most safe and efficient model with the maximum production.2- Coaching team for the operation of PHC kiln 5200 tpd KHD design - FLSmidth design upgraded during and after commissioning and a VRM with a capacity of 430 tph.3- I have led a suggestion to assemble a pilot burner at the tertiary air duct so as to increase the temperature of the tertiary air decrease the fuel consumption in the Pyroclon and increase the final calcination degree at the kiln inlet.4- I have led a suggestion for calculation of the oxygen content the lower cyclone and at the kiln inlet and proved the critical problem by calculations for the false air caused by the kiln inlet seal mechanical failure.5- Training for newly coming engineers to the plant (production department) including providing sessions about the mechanical, hydraulic & electrical systems overall view and operations and process calculation and introductory concepts with managerial supervised check list systems.6- Managing and planning of kiln area and VRM overhaul in addition to material requirement estimation for refractory jobs for the overhaul.7- Participate in the core cause analysis with other departments for the core cause determination for technical problems after passing through mini RCAs before reaching to that point.8- Making sure and revising of all work procedures in my specific area to confirm the safety of the the working procedures and prevent any risk that may occur under any sudden variables on site.9- Undergoing and contributing in KPI & OEE of the whole plant through the working committee.10- Following up and organizing with the laboratory foe the kiln feed analysis and clinker quality (LW, FL, CL, Mg . . etc.) and raw mix (sieve analysis 90/212 micro meter, LSF, SR, AR) for process optimization to maintain clinker quality. Show less

Egypt

1- Submitting daily operation conditions and performance reports & Process optimization and control.2- Leading and distributing tasks for operation group and technicians.3- Working on troubleshooting of operation and equipment.4- Participate in the annual overhaul and maintenance.5- Participating in the oxygen analysis and calculation in the system for determination of the critical weak points in the system causing the most false air in the system.6- Undergoing process… Show more 1- Submitting daily operation conditions and performance reports & Process optimization and control.2- Leading and distributing tasks for operation group and technicians.3- Working on troubleshooting of operation and equipment.4- Participate in the annual overhaul and maintenance.5- Participating in the oxygen analysis and calculation in the system for determination of the critical weak points in the system causing the most false air in the system.6- Undergoing process calculations for power efficiency and charging and mass balance and heat balance. Show less

Egypt

Handling all types of solvent & water borne formulas & new raw materials trialsAssembling of the ASTM testing for the Q.C [final products, production steps auditing, raw material testing].Responsible for active nanotechnology application in coatings research projectAssembling of the CLP regulation and GHS Labeling system and undergoing a study about reach regulationand the way to assemble some of its conditions for the SHEQ department

Oldenburg Area, Germany

have worked as an IAESTE student and become operational on the SECM (scanning electrochemicalmicroscopy) and also I have prepared a glucose biosensor, I became operational on the preparation of UMEs( ultra micro electrodes) as a nano and micro fabrication systems, I have been trained on using laser scanningconfocal microscopy so as to determine the rT & RG for the tip of the UMEs and determine its validity, Due tothe research assignments that I have worked on I have received a… Show more have worked as an IAESTE student and become operational on the SECM (scanning electrochemicalmicroscopy) and also I have prepared a glucose biosensor, I became operational on the preparation of UMEs( ultra micro electrodes) as a nano and micro fabrication systems, I have been trained on using laser scanningconfocal microscopy so as to determine the rT & RG for the tip of the UMEs and determine its validity, Due tothe research assignments that I have worked on I have received a certificate and a recommendation letterfrom Prof. Dr. Gunther Wittstock & for further information visit:www.wittstock.chemie.uni-oldenburg.de/de/staff/guests.html#summerstudents www.wittstock.chemie.unioldenburg Show less

Master'S Degree, Nanotechnology, Undergraduate

Material Engineering & Nano Advanced Materials

Non Degree Program, Physical Chemistry

Activities and Societies: weekend trips summer school culture have worked as an IAESTE student and become operational on the SECM.

Bachelor Of Applied Science (Basc), Chemistry, 75% V.Good

Activities and Societies: Charity Organizations Human Rights Organizations Scientific groups for research Female rights organizations i.

High School, General Studies, 92.5%

i have spent my whole school period in due this school including primary preparatory and secondary levels, finally i have been specified.