Duties and Responsibilities: Carry-out piping quality monitoring and inspections on PQR, WQT, and production weld. Prepare / generate welding follow-up sheets to update welding progress and NDT status. Routine coordination with piping team to implement accordingly the ITP particularly NDT applications. Witness UT (both lamination check on cladded bevel and flaw detection to detect defect depth) as per client request, attend and witness DPT & MPI (bevel / repair groove / after welding), perform welding visual inspections and review RT films (production weld & WQT). Monitor closely on weld repair (identify defect location & excavation / full joint cut-out / cut-out due to dimensional adjustment). Apply various means of setting-up purging block to maintain oxygen level in the purging area and complying WPS requirements, random check on misalignment during welding, and advise welders to follow welding sequence on stress-free joints to minimized distortion. Invite client (TechnipFMC) for the following witness inspections: DPT on bevel, joint fit-up, root penetration upon completion of fourth pass and removal of purging gas (pure Argon), weld visual inspection, verify defect location before cut-out / excavation, gauging test on selected piping upon NDT completion. Acceptance criteria as per ASME B31.3 / Tullow Specification (Specs 1118) and AWS. D1.1.

:: (A) Carry-out welding inspection for shop weld (fabrication shop) and field weld (site erection / final installation), (B) Handle RFI (Request for Inspection) from subcontractor and raised to Aramco QMIS (Quality Management Information System), (C) Typical daily routine welding related inspection: (1) Checking approved documents like; WPS (should be available nearby welding area), IFC drawing, method statement, JCC (Job Clearance Certificate) cards for welders (2) Calibration certificates for the following: welding machines, portable ovens, oxygen analyzer, clamp meter, and pyrometer (3) Checking and inspection of welding consumables during receiving, segregation, storage, baking / drying requirements, PMI batch test for SS / Copper Nickel filler wires and welding rods, (4) Carry-out inspection on production weld from fit-up, in-process, and post-welding visual inspection, (5) Attend / witness with PID for RT rejected weld joints during defects excavation and spool modification, (6) Witness / hold points on all tie-in inspection UG / AG piping golden joints that requires UT thickness gauging on existing line prior to post-cut activities, MT / PT on bevel, MT / PT on rootpass, capping, and RT / PAUT, (7) Verify and witness PWHT / hardness test, and PMI after welding, (8) Generate log / register for the traceability of all RFI raised to Aramco QMIS. (D) issue internal NCR to subcontractor for any surveillance report previously issued and no action has been taken and implement preventive and corrective action accordingly, (E) Monitor rejection rate of welders by performing toolbox meeting, doing actual interviews each welders to explain for any defects noted by RT and issue warning letters if necessary, (F) Close monitoring of subcontractor QC to follow inspection and test plan, timing in raising RFI, sequence in handling site inspection including NDT, and submission of corresponding test reports,

: (1) Review of work procedure and ITP, (2) Witness WQT, (3) Handle site quality inspections on eight (8) subcontractors (Yuhan Tech, AG&P, Woolim, GTC, FPI, Daemyung, Joongsan, and Seapine), (4) YUHAN TECH – WATER STORAGE TANK - padding / elevation, UT of annular plates, diesel test of shell-to-annular rootpass weld, roundness check of tank shell first course, fit-up / weld visual inspection, records of spot RT on tank shell, plumbness check / peaking / banding, tank nozzle opening / fit-up / weld visual / pad leak test, vacuum box test of bottom plates lap-weld joints, generate punch list (category “A” and “B”), tank settlement check (prior to water filling, 25%, 50%, 75%, test level, empty), hydrostatic test, tank release for painting, CWP – dimensional / fit-up / weld visual, 100% RT, pneumatic test, external wrapping / holiday testing, and internal coating / DFT, FIRE FIGHTING SYSTEMS - dimensional / fit-up / weld visual, HDPE visual fusion / bonding, hydrotest, coating / wrapping / holiday testing of underground HDPE valve and flange, and STATIC / ROTATING EQUIPMENT – padding / elevation / centering / pocket hole grout / plumbness / alignment / final grouting(5) AG&P – WQT – witness for plate and piping welder qualification, BOILER STRUCTURE ERECTION – column padding / elevation / orientation / plumbness / pocket hole grout / bolt torquing / final grouting, and DUCTING – visual and dimensional check before welding, (6) WOOLIM – WQT – plate welder qualification – GRP PIPING – lamination visual inspection / checking coordinates and elevation prior to concrete embedment, CONDENSER – equipment inspection due to noted damaged tubing from fabrication, (7) GTC – WQT – FCAW process plate welder qualification – STUD – dimensional / fit-up / weld visual / bend test – TOUCH-UP PAINTING – turbine building / fire water pump house / waste & waste water treatment building surface preparation of column splice joint / structural bolt connections, (7) FPI – GRP PIPING – assi

(1) SSE (Short Service Employee) for six (6) months contract duration as QA/QC site welding inspector, (2) Carry-out field weld related inspection both piping and pipe supports: check welding consumables / welders ID, fit-up inspection including dimensional and material identification, check WPS requirements prior to commence welding like; preheating using torch / tempilstick and or preheating machine using heating coil / thermocouple and chart recorder for alloy steels (A335 – P5, P9, & P11), random check on welding parameters during welding, welding visual inspection after post-cleaning (noted comments to be rectified by welders), (3) Orifice flange inspection: check tapping point orientation as per ISO drawing coordinates / elevation and reference from supplier during fit-up, internal inspection on rootpass flush grinding prior to issue RFI for client confirmatory inspection, (4) Conduct toolbox meeting to welding department and construction group any observe non-conformities during site surveillance like; traceability of welding consumable withdrawal to verify actual joints to be welded, unacceptable fit-up preparation, excessive weaving, unprotected weld pool, poor weld profile, missing joint ID (matrix), pipe supports incomplete welding / incorrect installation, weld encroachment / distance between two (2) adjacent / mask full-penetration welding, and pipe clashing, fillers shall be in proper containers, time / date / welder no. shall be written clearly on vacuum pack electrode upon opening to determine time exposure duration, heated quivers shall be maintain and its cap to be close during welding, (5) Assist in the tracing / excavation of weld defects found by radiographic test and continuous DPT application until all significant indications completely remove / DPT on repair groove prior to re-weld, (6) Periodic inspection and audit of welding consumables: color-coding of filler wires, baking of electrodes to be distributed to welders th

Reinforce QA/QC welding & piping Inspector at near completion of process piping pre-fabrication; (1) Generate detailed piping spools status, NDT request register, and piping inspection monitoring sheets (2) Carry-out welding visual inspection with the client, (3) Check status of weld joints that requires PWHT, particularly RT before / after PWHT respectively, (4) Offer NDT request, identify weld joints location, and coordination with production / welding department any repair weld joints has to be done, (5) Attend piping spool final visual / dimensional inspection with the client and assist in releasing for blasting / painting upon close-out of all related documents / NDT requirements, (6) Company representative on subcontractors (Friedlander, Luanda, Angola) GRE bonders training and qualification test started from checking adhesive storage, shaving on spigot-end, mixing of resin and hardener (potlife noted), application of adhesive (bell / spigot-end), preparation for alignment and bonding, final adhesive application, installation of heating element / checking its temperature, curing time, witness hydrotest, and sign hydrotest report, (7) Control piping hydrotest package (total of 287) and test package index, carry-out internal line checking to identify punchlist items / installation completion with corresponding register, (8) Taking responsibility on flange management activities like; generate flange management register, gasket / bolt length installed inspection, tightening requirements / torquing sequence and pump pressure checking, bolt protrusion and flange uneven gap check upon tightening / torquing completion. Reference standards as per ASME IX, ASME V, and ASME B31.3.

Responsible of the following : (1) Witness PQR, WQT, electrode batch testing, production test, and production welding, (2) Carry-out inspections prior to welding on the calibration validity of all welding related inspection tools / equipment (welding machine, multimeter, thermometer; probe type / laser type, vernier caliper, digital hi-lo gauge, & oxygen analyser), batch / lot nos. of shielding / purging gas, heat nos. of filler wire, electrodes, & parent material, and prepare inspection reports for the following: checklist before welding including joint preparation, check fit-up accurately prior to orbital welding (AMC Inc.), actual welding parameters base on pWPS / WPS requirements, verify actual current / voltage using multimeter (FLUKE), checking preheat / interpass temperature using probe-type thermometer (FLUKE), maintain / monitor oxygen level using oxygen analyser (INTERPURGE / model 772), assist in installation and maintaining oxygen level on water-soluble film (HUNTINGDON FUSION TECHNIQUES LIMITED) purge unit, visual of completed welding by boroscope (SBP), witness DPT & MPI, ferrite test (FERITSCOPE / FISCHER), hard stamping and markings of test coupon for mechanical testing. Carry-out partial / full parameter monitoring on superduplex spools & jumper (6”, 2” & ¾” Ø) production welding in parallel with visual inspection of its support clamps and frames. Reference standards as per ASME IX, ASME V, ASME B31.3 and AWS D1.1 / TOTAL Specification.

(1) Inspections on the material receiving that includes visual, material identification, and transferring heat numbers before cutting, (2) Review of drawings (prepare welding maps / pdf copy), identify and markings of pre-fabrication spools including joint ID, and signage for requested joints for RT, witness PQR & WQT, (3) Hold points on the following: (A) prior to welding, (B) during welding,(C) after welding, (4) Prepare RFI’s for RT, UT, MPI, DPT and attend during NDT inspection, conduct ferrite test on superduplex, and prepare inspection reports on pickling / passivation after visual and pipe wrapping prior to transport bound to offshore, (5) Interpret RT films both structural and process pipings including the tracing of defects and instruction to welders for defects location / DPT on repair groove prior to welding / monitor welders rejection rate and further penalties for 10% RT requirements / 10% RT for gap check (SW), prepare visual reports, generate welding follow-up sheets / PWHT instruction sheets, clearing all NDT’s as per ITP / review of PWHT chart as per approve procedure, take actions on issues receive through e-mails and non-conformity observe by client, prepare hydrotest package, and sent notification to client for attending / witnessing hydrotest, (6) Prepare and generate dossiers (manufacturing record books / total 26 MRB’s) that includes attachment like; ITP (Inspection and Test Plan), MTC (material test certificates), WPS, qualified welders, fit-up / visual / NDT / PWHT / hydrotest / pickling & passivation / painting / pull-off test / holiday test / DFT test reports for client review and comments / approval, any noted comments shall be rectified accordingly. Reference standards as per ASME IX, ASME V, ASME B31.3, AWS D1.1, and Total Specifications.

(1) Implement quality control at fabrication shop (AIC & Saudi Metin), (2) Closed monitoring at fabrication shop / site erection to attained WPS requirements, and random visual and dimensional inspection with subcontractor for conformity, (3) Issue surveillance notice to subcontractor, (4) Revised site quality documents and incorporate client comments, (5) In-charge / take actions on QA/QC issues received through e-mails, (6) Preside the QA/QC weekly meetings to discuss the following: client NCR status / issued surveillance notice to subcontractor, status of method statement to be issued and further client approval. and discuss corrective action on issues noted by client during joint inspection, (7) Conduct internal audit to subcontractors and assist in preparing project dossiers prior to handover. Reference standards as per ASME IX, ASME V, and AWS D1.1.

(1) Carry-out visual and dimensional inspection with the client on the following: boiler intake and exhaust ducting assembly, required gap and clearance on impeller and inlet cone / rotor shaft bearings, functional test for closed and opening of dampers for boiler forced draft fan / induced draft fan, (2) RT film interpreter for internal pipings (100% RT), and external pipings (20% RT), (3) Daily monitoring of site welding activities, (4) Update of QCP (Quality Control Plan) as per actual site inspections and submitted reports from the subcontractors, (5) Conduct monitoring, internal, and confirmatory inspections of ducting, equipment, and piping insulations and jacketing, and (6) Attend DFT check on primer coat, and touch-up on damaged painting for main and secondary steel structures due to transport and site installation, and final visual and DFT on top coat with the client. Reference standards as per ASME I, ASME VIII Div. 1, ASME B31.1, and ASME B31.3.

1) Review, familiarization, and implementation of the approved ITP, witness welder qualification test, monitor storage/handling of welding consumables, 2) Witness/hold points of the following: STORAGE TANKS; Installation of cathodic protection and succeeding test with the client, spot RT on annular plates prior to shell plates erection, welding sequence on bottom plates, shell-to-bottom plates rootpass welding (diesel test inside/MPI outside), vacuum-box test on bottom plates lap-weld and shell-to-bottom plates full penetration welding, roundness check on shell plates (first course), plumbness check from first course to last course, selection of spot RT as per API 650, inspection of peaking and banding, pneumatic test on nozzle/manhole reinforcing pad, topographic survey of tank settlement check (from 0, 1/4, 1/2, 3/4, & full with 24 hours duration each interval), take water sample (ph level) each water truck delivery, inspection of internal floating roof for any distortion / clashing on its guide post/firmness of perimeter seals during water filling, hydro-pneumatic test using manometer in parallel with functional test of pressure/vacuum relief valve at tank roof, and check surface preparation after sandblasting, primer coating, DFT/holiday testing after top coat application. SPHERE TANKS: RT film interpreter (100% RT) before PWHT, witness UT flaw detection (100% UT) before and after PWHT, and witness MPI (100% MPI) before backwelding and after welding, 3) Attend weekly QA/QC meeting to incorporate any issues like approval of commented documents, and field inspection/non-conformance report closed-out, 4) Company representative during scheduled audit by client, 5) Update welding follow-up sheets, client approval of all fit-up/visual/dimensional/NDT reports, and prepare test package for client review, 6) Closed-out all remaining punchlist items, prepare final dossiers and turn-over documents to client. Reference standards as per ASME VIII, Div. 1, and API 650 / 620.

(1) Closed monitoring of inspection and testing of storage tanks and sphere tank, (2) RT film interpreter on spot RT on storage tanks, 100% RT on sphere tank, 20% RT on process piping, & 100% RT on SS high pressure process piping, (3) Implement ITP through subcontractor, review hydrotest procedure, check test package, clearing all NDT requirements, and line checking to categorized noted punchlist items prior to hydrotest, (4) Send notification to client to attend / witness hydrotest, service test of fire hydrant at tank roof perimeter, and succeeding water flushing / air blowing, attend reinstatement like closed-out of category "B" punchlist, installation of pumps / flow meters / check valve / orifice flange / witness bolt torqueing, assist in the preparation of final QA/QC documents for client review and approval. Reference standards as per API 650 / 620 (low pressure storage tank), ASME VIII, Div. 1 (sphere tank), and ASME B31.1 & ASME B31.3 (piping).

PETRON REFINERY: 1) Review EPC contractor's submitted ITP to conformed Petron project specification and standards, 2) Random check on applied NDT on site including random film interpretations, 3) Attend hydrotest, line checking, and review of hydrotest package, 4) Witness painting final inspections that includes DFT and holiday testing particularly on underground piping, 5) Calibration of PSV's, 6) Coordinate with EPC contractors QC inspectors on the daily basis. NDT-PHILS.: 1) Cebu Branch Coordinator-supervised, conduct marketing for the prospective projects, follow-up billing/collection, and monitor calibration certificates of all NDT equipments and accessories (from May 1, 2005 to January 15, 2006), 2) TML of various existing pipelines during plant turnaround at MEROX, APS2, & GOHF/Petron Bataan Refinery, 3) Re-qualification of two bullet LPG hemispherical tank, calculation of MAT through design and actual thickness, corrosion rate, and remaining life expectancy/Mundogas, Danao City, Cebu, 4) Carry-out radiographic test using gamma-ray on ship hull of Western Venturer to monitor the integrity of the newly welded patch plate/Keppel Cebu Shipyard Inc., Lapu-lapu City, Cebu, 5) Conduct radiographic test using X-ray machine, dye penetrant test, and holiday testing on the fabricated intake and discharge piping for the cooling system of Mindanao 210 MW Coal Fired Power Plant/KMP Engineering, Lapu-lapu City, Cebu, 6) Radiographic test using gamma-ray of field welded boiler piping/holiday testing of underground piping for the cooling system of coal fired power plant/Formosa Heavy Industries, True North, TIPCO, Mabalacat, Pampanga, 7) Carry-out UT flaw detection and dye penetrant test at Subic Freeport/JFE Civil Engineering and Construction Group, Subic Freeport, Zambales, 8) Out-of-Service inspection of oil storage tanks, responsible for inspection of out-of-plumbness, verification of bottom and shell plate thickness, and other owner required test requirements, and provi