Key Responsibilities: Performed design check according to NCC section J, Mechanical Spec. and Green Star and PCA regulations  Designed and drafted technical drawings (Air Schematic, Chilled water schematic and Heating hot water schematic) Performed Static calculation for air distribution systems as well as water distribution network Designed air distribution ductwork including: duct sizing, thermal and acoustic insulation, fittings, VCD and motorized dampers and air… Show more Key Responsibilities: Performed design check according to NCC section J, Mechanical Spec. and Green Star and PCA regulations  Designed and drafted technical drawings (Air Schematic, Chilled water schematic and Heating hot water schematic) Performed Static calculation for air distribution systems as well as water distribution network Designed air distribution ductwork including: duct sizing, thermal and acoustic insulation, fittings, VCD and motorized dampers and air diffusion equipment Provided refrigerant calculation for AC units Designed and sized chilled water and heating hot water systems  Provided Air Balance at normal mode, Economy cycle and Pandemic mode and in case of providing CO2 controller Designed ventilation systems including supply, outside and exhaust and recycling air systems Provided calculation report for car Park and kitchen ventilation  Checked Heat load calculation report Designed fire and smoke control systems based on AS1668 including fire and smoke dampers, Stairwell pressurization system, mechanical and natural Smoke exhaust system, Stair relief system, Zone pressurization system) Prepared Fire Matrix  Provided Fire penetration treatment schedule for openings in fire-resistant elements Designed and selected fans Performed design check and selected HVAC equipment including: AHU, FCU, PAC Unit, AC Unit, Chiller , VCD, Attenuator and pump Show less

Sep 2008 – Apr 2015 and Sep 2016 – March 2019Provided following tasks for preparing technical bid proposals for more than 30 thermal power plants in Iran & the Middle East of which %70 were successful:• Prepared HAZOP (Hazard and operability study) and identified and evaluated problems that may represent risks to personnel or equipment.• Prepared technical specification for fire suppression systems and specified requirements for the components and main equipment of fire protection… Show more Sep 2008 – Apr 2015 and Sep 2016 – March 2019Provided following tasks for preparing technical bid proposals for more than 30 thermal power plants in Iran & the Middle East of which %70 were successful:• Prepared HAZOP (Hazard and operability study) and identified and evaluated problems that may represent risks to personnel or equipment.• Prepared technical specification for fire suppression systems and specified requirements for the components and main equipment of fire protection systems.• Provided technical specification, calculation and provided equipment selection for HVAC systems. • Prepared PFD (Process flow diagram)• Interacted, followed up, coordinated meetings and office correspondence Coordination with other services in addition to the authorities and architects and clientMay 2006 to Sep 2008: provided following tasks in pre-construction (bid process) phase for Yazd Solar Power Plant, GHAEN, CHABAHAR and MOBIN simple cycle power plants, PARESAR and SOUTHPARS combined cycle power plants:• Developed tender documents for firefighting systems, fuel oil storage and supply system and fuel gas station according to approved basic documents for holding tenders in order to select subcontractors • Reviewed and evaluated technical bids to select sub-contractors July 2005 to May 2006:provided following tasks during construction phase for GENAVEH, TOUS, ASALOUYEH and ARDABIL simple cycle power plants:• Reviewed detail design documents provided by sub-contractor • Reviewed and changed PFD and pipe route drawings provided by sub-contractor if needed• Performed periodic reviews in order to check the accuracy and quality of work and test the equipment Show less

I provided following tasks for NEKA combined cycle power plant:• Performed hydraulic calculation for water main and water supply network in firefighting systems• Designed and modelled pipe route drawings for all part of the thermal power plant• Designed and modelled piping arrangement drawings• Selected pipe support according to pipe stress analysis reports(performed by other individuals) and pipe support standard• Modelled pipe supports using AutoCAD• Attended… Show more I provided following tasks for NEKA combined cycle power plant:• Performed hydraulic calculation for water main and water supply network in firefighting systems• Designed and modelled pipe route drawings for all part of the thermal power plant• Designed and modelled piping arrangement drawings• Selected pipe support according to pipe stress analysis reports(performed by other individuals) and pipe support standard• Modelled pipe supports using AutoCAD• Attended meetings with the client in order to clarify unclear issues for getting client’s confirmation• Coordination with other services• Coordination with authorities and architects Show less

I provided following duties in 4 main areas of 9th OLEFIN refinery and 6 main areas of 10th OLEFIN refinery in Persian Gulf:• Designed pipe route drawings• Designed piping arrangement drawings• Modelled piping arrangements using PDS software• Performed clash check of whole plant using SMART PLAN software• Modelled pipe supports (Designed by others) using PDS software