Calibration tuning of hardware specific to meet engine requirement according to ECM & application.Follow DVP&R schedule and complete the tasks to meet the program timelines.Support at customer end in tuning, testing and troubleshooting on issues.Calibration tuning & verification on diagnostics as per customer requirement.Current product support as needed.

-Converting the requirement into concept and forward it to design.-Co-ordinate with manufacturing for Proto type making.-Testing to evaluate the Concept.- FIE calibration on test bench using Delphi Development tool VISU-Generic system validation -FIE failure Analysis-Coordinate with customer relating to product development activities.-FIE Calibration -FIE to engine installation check-Developing a base calibration for the engine -Calibrating various sensors associated with engine (AMF, TMAP, Boost etc)-Achieving the target points (Torque, Power, BSFC, Smoke etc).-Fuelling & torque management calibration-Full load and part load engine calibration-Pulse Map Generation-Model Air calibration-Speed pilot Control Calibration.-Fault Management Calibration -Optimizing the engine & vehicle to meet eligible emission norms in engine & chassis dynamometer

Calibration & tuning of hardware matching to engine requirement.Delivering calibration schedule as per customer requirement.support in engine testing to tune and deliver Fueling error diagnostics

Engine & Vehicle calibration / Product development-Converting the requirement into concept and forward it to design.-Co-ordinate with manufacturing for Proto type making.-Testing to evaluate the Concept.- FIE calibration on test bench using Delphi Development tool VISU-Generic system validation -FIE failure Analysis-Coordinate with customer relating to product development activities.-FIE Calibration -FIE to engine installation check-Developing a base calibration for the engine -Calibrating various sensors associated with engine (AMF, TMAP, Boost etc)-Achieving the target points (Torque, Power, BSFC, Smoke etc).-Fuelling & torque management calibration-Full load and part load engine calibration-Pulse Map Generation-Model Air calibration-Speed pilot Control Calibration.-Fault Management Calibration -Optimizing the engine & vehicle to meet eligible emission norms in engine & chassis dynamometer

Current ResponsibilitiesCoordinate with Delphi France & U.K Technical Center to integrate the FIE Product development.To release the engine calibration software for the ECUTo develop a fault management for the vehicleSupport activity at customer end for new software release and testingDiagnose faults and rectify to solve Support field issuesAPPLICATION DEVELOPMENT:FIE to engine installation checkDeveloping a base calibration for the engine Calibrating various sensors associated with engine (AMF, TMAP, Boost etc)Achieving the target points (Torque, Power, BSFC, Smoke etc).Fuelling & torque management calibrationFull load and part load engine calibrationPulse Map GenerationModel Air calibrationSpeed pilot Control Calibration.Fault Management Calibration Optimizing the engine & vehicle to meet eligible emission norms in engine & chassis dynamometerProject #2: Development of Fuel Injection Equipment for 800 cc NA diesel engine (2007-2009)Development of Electromechanical controlled fuel injection system for 800 cc NA diesel engine.Definition of Fuel injection equipmentFIP prototype building, testing & validationProduct performance optimization to suit engine requirement.Initial full throttle performance and emission study on engine test rig by swingNozzle selection by full load engine performance test and by modal points emission testNozzle tip protrusion trials to fine tune full load performance and emission

Developed and conducted the cam box trials for new two cylinder engine with unit pumps.Conducted performance trials for new two cylinder compact engine.Introduced Belt tensioner assy. for genset applications replacing the alternator and achieved cost reduction.Modeling, Assembly and Detailing of 2, 3 & 4 cylinder engines using Pro/E and Auto CAD.Preparing General Arrangement drawing for engines.Detailed drawings of parts using Auto CAD.To develop the new parts as per customer requirements.Preparing DFMEA for critical parts.Preparing the Bill of Materials for parts catalogue.Development testing of engines for validation.

Job Responsibility: Development and follow-up of new products.Coordinating with customers regarding development products. Convert customer drawings to In-House drawings.Co-ordinate with manufacturing team to develop the parts and getting approval from customers.Maintaining documents related to development activities.Acted as a key player for ISO 9001:2000 and related activities. Implement 5s activities.