REVAMPING... Disassembly of valves smaller than 2 inches flanged and welded, disassembly of critical process valves, disassembly of PSV valves, gate valves, butterfly valves, check valves, etc... disassembly of pumps for general maintenance, centrifugal pumps, vertical, multistage, buster pumps, etc. .... General overhaul of pumps, complete disassembly, mechanical maintenance to internal parts, bolts & nuts, sandblasting, rust removal, application of penetrating liquid to detect cracks in the structure, detection of axial and radial displacement, shaft rectification, impeller balancing, change of bearings, change of seals, application of anticorrosive paint to the external case, complete assembly, seal tightness test, vibration test and issuance of certificates. Lifting of vertical pumps from the cooling tower using 70 and 250-ton cranes, lifting maneuvers of vertical pumps, Cleaning of the internal pit, removal of mud and stones (confined spaces), supervision and maintenance of prilling tower equipment, preparation of CO2 lines, low and medium pressure steam, blowing of air and steam pipes, cleaning of the cooling water circuit, fabrication of connections (spool), handling of ammonia water, handling of off-spec products, internal cleaning of process columns (Carbamate), installation of flanged and weldable valves using acid electrodes with Cr-Ni-Mn compounds.

Technical Advisor for maintenance plan

Obtaining professional certificates

Operation & Maintenance of HOWDEN GAS Compression package, Propane Scrubbers, Propane Acumulator, Compressor Oil separator, Propane Recovery System from Chillers & Scrubber......CRM Condensate Recovery Maximization ProjectPosition: Operation & Maintenance ManagerProcess:Experience in HOWDEN Propane Compressor K-3011 K-3012Experience in LUB Oil PumpsExperience in Lub Oil Separator (Oil Level, Demisters, Gas Filters)Experience in Gas Oil SealExperience in Motor Oil pumpsExperience in Chillers (Heat Exchanger)Experience dismounting & Mounting (31-32) PCV 751, PCV 761, PCV 764, etc... Komoto Valves (Buterfly Process Valves) after passing detection (removed ans sent to NIZWA, STS Work Shop for to repairing)Experience in Propane filling from the MUSCAT Gases company to Our Propane Acumulator 50m3 per truck.Propane Leaks investigationStart up procedure implementation after Process Shut DownStart up after of a non normal shutdownPre Start up prepation in the propane compressor due to SLIDE VALVE condition.Lub oil feeling for the lub oil separator (OIL 150)Oil gas seal feeiling Oil 32Motor Oil feeling Oil 22Propane Pressurization & DepressurizationPropane HandlePropane Chillers Pressurization & DepressurizationFire & Gas System ManagementN2 handle for Purging the propane lineExternal filtration package applied for the propane pipeline systemLub Oil filter change (John Krane) (Howden) Hot change & Cold changeCompressor N2 PurgingCompressor Propane Depressurization ManagementAdministration:Experience in Employee handle (DCS Operator, Maintenance Team)Experience in PERMIT HOLDER, PERMIT Applicant and Area authorityExperience in employee RotationExperience in SAPExperience in Vendors: Schneider, Howden, Honeywell, Bently Nevada, Alalaufi, JORD, etc…..Maintenance:Prevcentive & Corrective MaintenanceDepressurizing & Pressurizing equipment with propaneInternal inspection to the vessel.

Technical Assistance & trainer for Libyan Operators in all duties in SRU Plant, Shift Supervisor.- Start Up & Shutdown, Operations of follow areas:Unit 581- MDEA (Methyldiethanolamine) AbsorptionUnit 582- SULPHUR RECOVERY UNIT (SRU)Unit 583- TAIL GAS TREATMENTUnit 584- THERMAL INCINERATORUnit 585- SULPHUR DEGASSING UNITUnit 586- MDEA STORAGEUnit 587- Sour Water StrippingUnit 632- Liquid Sulphur Tank Area.

1.-To monitor always the SRU plant (train 1, train 2 and train 3) 2.-To monitor always the LPG and NGL Plant (train 1 and train 2)3.-To take daily the samples (Rich amine, Lean amine, Acid gas, H2S in the sulphur PIT)4.-To monitor all the process, especially amine pumps, thermal reactor (Combustions air, fuel gas, nitrogen use).5. - To prepare and sign the PTW6. - To follow the Maintenance JOBs according with the PTW7. - To give support in site to all personnel involved in the process8. - To follow all the normative according with the safety department9. - To prepare HOT Work permit, Confined space permit, Entry Permit for Vehicles/Machines10. - To prepare the PTW for X-Ray test, PTW for erecting….. etc…..11. - To monitor the process for possible leaks (steam, liquid products and gas products…)12. - To monitor all the vibrations and malfunctioning of the machines, levels, pressures, concentrations, combustions, etc…13. - to prepare the shift report.14.- Planning & Following in Maximo Software the maintenance15. - to record in the maximo software all the unexpected maintenance to be done.16.- Start up and Shut Down all the plan in safe condition

To prepare all procedures to operate in safe way the plant. Expansion (Revamping)Unit 200 LP (Low Pressure) Separator (Tri Phase Separator).Unit 200 MP (Medium Pressure Separator) Separator (Three Phase Separator)Unit 220 Crude Oil Storage Tank, Transfer Pumps and Metering SystemUnit 300 NAG Separator (Non Associated Gas Separator)Unit 300 NAG II Separator (Non Associated Gas Separator)Unit 200 TEST Separator Unit 200 Samabri / Biseni SeparatorUnit 230 Blow Down System (Flares) (KO Drum)Unit 560 Open & Close DrainUnit 360 LP Compression AreaUnit 360 MP Compression AreaUnit 190 Inlets FacilitiesUnit 420 Fuel Gas ConditioningUnit 560 Open and Close Drain.

Pre Commissioning, Commissioning activities, Blowing & Cleaning Procedures Preparation, OTP', flushing, Start Up, Performance test, Operations, Training.63 Service Air63 Instrument Air64 Nitrogen LP64 Nitrogen HP50 Albien Fire Water50 Raw Water Eocene52 Raw water and Storage71 Fire Water System20 Inlet Separation20 Inlet Separation up to Gas Compressor 1,2,3 & 423 Gas Compression Train 1,2,3 & 4 Inlet and discharge23 Lube Oil Gas Compression Train 1,2,3 & 424 Feed gas Driers train 1,2,3 and back to compression headers24 Gas Treatment feed gas driers train 1,2 & 332Absorber Train 1,2 & 332 Deethanizer Train 1,2 and 332 Regeneration fired heater train 1,2 & 332 Isopenthane to off specification tank33 Process to On Specification LPG sphere and Piping33 Off Specification LPG Spheres and piping to Export33 Off Specification condensate and Storage41 Hot Oil system to reboilers all trains44 Oily Water system treatment Pre Deoiled Effluent57-010 Closed Drain separation57-031 Closed Drain Hot 57-041 Closed Drain Cold43-011 Warm Flares43-014 Warm Flares Compressor43-041 Low Pressure Flares Compressor43-021 Low Pressure Flares43-022 Cold Flares train 1,2,345 HP and LP Fuel Gas system45 LP Fuel gas system62 Diesel Systems69 Lub Oil Treatment53 Potable Water66 Sewage Water Treatment42-010 Chemical Injection Biocide43-021 Chemical Injection Corrosion inhibitor42-022 Chemical Injection Inhibitor gas Phase42-030 Chemical Injection Methanol42-031, 032, 033 Chemical Injection Methanol Train 1,2 and 342-034 Chemical injection Methanol Compressor.

Commissioning Supervisor.Commissioning, Start Up, Operations and Support on site to the client: R3 Fire Water Tanks and Deluge System R5 General Electric Gas Compression StationR6/R7/R8 (Oil Crude Stabilization train 10/20/30): Three Phase & two phase Separator, desalter unit, Reboiler Unit, Stabilization Unit and cool down Unit. Chemical Dosing Package. R9 Water Oily Treatment Unit and anti-coagulant dosing package R10 (Gas Off Spec Unit) R11 Foam system Unit for the fire water system and Deluge System R011 (Utilities Unit; Lp /Hp Nitrogen Plant, Air process and Instrumentation Air Plant)R201 Fire Water System Jockey Pumps and Biocide dosing packageR203 (Fire Water System; Diesel/Electrical Pumps)R205 Exportation’s Pumps (horizontal), Booster Pumps (vertical).R111 (Gas Pig trap System)

To Provide Training for the locals operators in order to teach them to operate the plant. and the same time to supervise the operations and to cover the missing positionsTo monitor Saturated Steam Boilers levelsTo Monitor Level of Sulphur CondensersTo monitor levels in the amine surge Drum as also Concentration and temperature To Monitor Sulphur Pit LevelTo Monitor Sulphur Storage Tanks levels and temperature in the sulphur farm area in order to avoid unnecessary sulphur dust and gases.To monitor cooling water system temperature specially during summer seasonTo monitor Chemicals dosing To monitor Tail Gas SystemTo monitor Amine Heat Exchanger (due to 2 years later of the first start up the facing tube into the heat exchanger got some internal damage carrying amine from the heat exchanger to the cooling water tower.To monitor the Precoat Filter Process in order to filter the amine and optimize the process.To Monitor the degassing pit process carefully (due to 1 year later of the first Start up, the degassing line was blocked by sulphur dust avoiding the degassing process).To control all parameter of the chemical process in the Sulphur Recovery unit especially in the Clauss Catalytic Converter Process.To Monitor the Caustic Soda Injection in order to avoid internal Pipe Corrosion To monitor the chemical dosing in the amine system in order to avoid (Internal Foam and Corrosion) To monitor the Daily samples done in the Boiler feed water, amine and water in the sulphur condenders, cooling water system as also in the sulphur pit in order to takes necessaries actions.To monitor H2S detector in the Critical Areas.To monitor instruments AlarmsEtc…

Pre-Commissioning & Commissioning in the construction stage. Start Up – Control Room Operator, Operations & Maintenance of follow areas:Unit 581- MDEA (Methyldiethanolamine) AbsorptionUnit 582- SULPHUR RECOVERY UNIT (SRU)Unit 583- TAIL GAS TREATMENTUnit 584- THERMAL INCINERATORUnit 585- SULPHUR DEGASSING UNITUnit 586- MDEA STORAGEUnit 587- Sour Water StrippingUnit 320- NGL Fractionation (De Ethanizer & Debutanizer Process)Unit 631- SANDVIK PROCESS UNITUnit 632- Liquid Sulphur Tank Area.Experience in Acid Gas, Sour water feed to SWS unit, Flash Gas to Thermal Incinerator, Regeneration Fuel Gas to thermal incinerator, liquid Sulphur, Stripped Water from SWSSteam, Condensates, Demineralized Water, Boiler Feed Water, Sea Water, Cooling Water, Desalinated Water, Potable Water, Fire Water, Compressed Air, Nitrogen, Low Pressure Fuel Gas. H2S Absorption & MDEA Regeneration, Pre coat Filter, Antifoam & Anticorrosion Package.Acid Gas feed unit feeding to claus unit, combustion air feeding to claus unit, claus burner, Waste Heat Boiler, Sulphur Condenser & Catalytic Converters, Final condenser & Tail Gas Coalescer, Liquid Sulphur Pit.Tail Gas Treatment, Hydrogenation, Water Removal, H2S AbsorptionThermal Incinerator heating up, Thermal Incinerator Burners Lightning, Claus converter Heating up, Boiler Pressurization, Sulphur Pit Purge Start Up, Sulphur Degassing Start Up, First Sour Water Stripping Unit Start up, First Amine Absorption Unit Start Up, MDEA Solution Circulation, MDEA Regenerator Start Up, MDEA Filters & MDEA Filtration Package Start up, First Tail Gas Treatment Unit Start Up, MDEA Section Start up, MDEA Storage Start up.Thermal Incinerator Heating – Up, Thermal Reactor Burner Lightning, Claus converter Heating Up, Boilers Pressurization, Sulphur Pit purge Start-up.Low Low Pressure Steam, Low pressure Steam, Medium Pressure Steam, and High Pressure Steam.Experience in NGL Fractionation (Debutanizer & Deethanizer Columns)

SANVIK Certificated Expert for to Operate & Maintenance the Sandvik Sulphur Prillers.SANDVIK (Prillers) Mechanic Expert TECO Westinghouse Horizontal Pumps Operation & Control, Lubrimate System, Automatic Valves, Solenoids, Manual Valves, Vertical Pumps, ETC.Pre Commissioning & Commissioning Activities Experience , Hydrostatic Test, Pneumatic Test, Flushing, Piping, Pigging, Witness Steam Blows , 16” Bridle, Pumps Alignment, Systems Alignment, etc.Solid & Liquid Sulphur Export Procedures, Equipment & Heating Systems Effective Maintenance Plan Preparing, etc...DCS Chief Supervisor, DCS Operator, Sulphur Operator in the area 9602 & 8100 From Sincor UPGRADER Solid & liquid (Coke & Sulphur) Handling Project , Loading Arm Operator (Cheek Sam), Ship loader Operator, Radial Stacker Operator, Stacker Operator, Reclaimer Operator.IT Chief Supervisor from Office Building & Service Building.Alarm & Warning Control, Security System Control & Process Fail.PLC Way Process Control – Control NET.Vessel Loading Plan.Steam Line Heating System Expert; Maintenance & Fixing.Steam Leaks Maintenance & Fixing, Spirax Sarco steam traps Maintenance.12” & 16” Liquid Sulphur Line Block Detection Expert Industrial Security & Environment (HMA) (HIS).Liquid & Solid Residue Handling. (Grease, Oils, Chemicals, Gas, Mud, Steam Trap Water, etc...)Petroleum Coke Handling Project (VEHOP: Very Extra Heavy Oil Project), Belt Conveyors Experience, Transfer Tower System Experience, Coke Stacker Experience, Reclaimer and Ship loader Experience.Shiploader Experience using the remote controller and cabin controller.6 km belt conveyor system pipeline for minimize the dust in the environment. (From the pile stack to the jetty).Experience in sulfur stacking in an Open area and a Close areaSCADA S/3 DCS Operator (Coke and Sulphur) Ship loader Operator (for Coke and Sulphur) in the Petrozuata Dock (Jetty)Sandvik Operator (for Sulphur)

Honeywell Plant Scape DCS Operator (Coke and Sulphur) Stacker Operator (for Coke and Sulphur)Reclaimer Operator (for Coke and Sulphur)Ship loader Operator (for Coke and Sulphur) in the Petrozuata Dock (Jetty)Sandvik Operator (for Sulphur)