• Technical support to review Risk assessment documents, hazard identification and abandonment plans for Offshore facilities given in Z2B block – upstream facilities (HAZID, What-if / Checklist, Quantitative Risk Assessment - QRA for Offshore platforms and Onshore facilities)• Optimization studies of compressor stations and other facilities, assessing tenders and overseeing technical proposals.

• Feasibility studies, Design and Retrofit of existing offshore and onshore production facilities (Delfin, Corvina 11, Corvina 15 and Albacora Platforms - Z1 block and 192 Block. Collect data and perform writing reports of current conditions, perform the assessment in production sites. Heat and material balance for new projects and process equipment (Simulation reports). Creation of process flow diagrams (PFDs) and piping and instrumentation diagrams (P&IDs) keeping drawings updated and… Show more • Feasibility studies, Design and Retrofit of existing offshore and onshore production facilities (Delfin, Corvina 11, Corvina 15 and Albacora Platforms - Z1 block and 192 Block. Collect data and perform writing reports of current conditions, perform the assessment in production sites. Heat and material balance for new projects and process equipment (Simulation reports). Creation of process flow diagrams (PFDs) and piping and instrumentation diagrams (P&IDs) keeping drawings updated and available. Performing hydraulic and process calculations and facilities design. Technical evaluation related to the procurement of materials, equipment and instruments at various EPC projects.• Review of design aspects for consistency and safety, including commissioning procedures and HAZOP studies of several facilities. Show less

• Design work for power generation systems. Basic design work for air sparging and heating systems.• Responsible for timely progress and completion of process discipline deliverables in design phases setting priorities.• Provide discipline support to other disciplines. Coordinating with clients, local authorities and consultants, tracking costs and progress. Preparation and reviewing of deliverables for discipline, such as process diagrams (PFD and P&ID), process design basis, equipment… Show more • Design work for power generation systems. Basic design work for air sparging and heating systems.• Responsible for timely progress and completion of process discipline deliverables in design phases setting priorities.• Provide discipline support to other disciplines. Coordinating with clients, local authorities and consultants, tracking costs and progress. Preparation and reviewing of deliverables for discipline, such as process diagrams (PFD and P&ID), process design basis, equipment lists, equipment data sheets, instrument process data sheets, hydraulic calculations, control valve sizing, venting capacity calculations, basic engineering design data reports, process description reports, PSV sizing, operating manuals, operation, control and emergency shutdown philosophy reports, cause & effect diagrams. Show less

• Design work and optimization for Offshore facilities.• Active participation in work meetings with customers and other stakeholders, providing documents such as proposals and correspondence for projects. Preparation of SOW (Scope of work) & SOR (Statement of Requirement). Process design (Feasibility studies, Conceptual design, FEED), changes and process optimization as well as HAZOP studies according to the local and national regulations, procedures and policies.• Develop material and… Show more • Design work and optimization for Offshore facilities.• Active participation in work meetings with customers and other stakeholders, providing documents such as proposals and correspondence for projects. Preparation of SOW (Scope of work) & SOR (Statement of Requirement). Process design (Feasibility studies, Conceptual design, FEED), changes and process optimization as well as HAZOP studies according to the local and national regulations, procedures and policies.• Develop material and energy balances; Preparation & Review of Process Flow Diagrams (PFD) and Process and Instrumentation Diagrams (P&ID). Develop design deliverables related to Oil & Gas separation, and all major topside facilities, Hysys simulation reports, equipment sizing calculations, Gas Lift systems, utilities, desalting units, production separator sizing calculations, scrubbers and vessels, liquid separation systems and filtering, gas compression units, production optimization, debottlenecking analysis, flaring systems, relief valve sizing, flare headers sizing, LACT systems, starting systems for gas compressors. Perform site visits with engineers and operations team, data analysis, determining information requirements. Provide discipline support, working as part of a multi-disciplinary team from Colombia, Mexico and Peru to develop associated deliverables. Show less

• Water treatment design utilizing reverse osmosis and demineralization for the steam cycle and power turbines, analyzing options related to water disposal permits according to local regulations.• Design support in power generation facilities such as Combined cycle power plants and water treatment. Design support in storage facilities. Hydraulic calculations, instruments and equipment data sheets, heat and mass balances, procedures, equipment list. Analysis of major and minor equipment -… Show more • Water treatment design utilizing reverse osmosis and demineralization for the steam cycle and power turbines, analyzing options related to water disposal permits according to local regulations.• Design support in power generation facilities such as Combined cycle power plants and water treatment. Design support in storage facilities. Hydraulic calculations, instruments and equipment data sheets, heat and mass balances, procedures, equipment list. Analysis of major and minor equipment - gas turbines, steam turbines, HRSG and pipelines, stack design for combined cycle. Preparation of heat and material balances, water and steam balances, PFDs and P&IDs.• Wastewater treatment support for an oil producer accommodation – requirements of information and data processing to design a wastewater plant for effluents from kitchens, washrooms, and industrial laundry facilities - Aeration, biological, gravity settling and activated sludge digestion models. Show less

• Perform facility failures analysis in oil and gas equipment, water treatment facilities, vessels, pipelines, pumps to find the conditions for decreasing future failures. Assessment of artificial lift systems failures, Sucker rod failure analysis reports, to improve the current design and the decision process of components selection for certain oil well conditions and minimize future failures (sucker rod barrels, seats, balls, pipes, tubing, rods, sucker rod couplings and other components)… Show more • Perform facility failures analysis in oil and gas equipment, water treatment facilities, vessels, pipelines, pumps to find the conditions for decreasing future failures. Assessment of artificial lift systems failures, Sucker rod failure analysis reports, to improve the current design and the decision process of components selection for certain oil well conditions and minimize future failures (sucker rod barrels, seats, balls, pipes, tubing, rods, sucker rod couplings and other components). Fluids analysis activities (physicochemical and instrumental), chemical products testing and corrosion failure assessment with contractors, corrosion measurement, material analysis and testing by a third-party testing laboratory. Specialized testing (X-ray, hardness, metallographic techniques, metallic coating thickness).• Monitoring of process variables for optimizing oil & water separation treatments. Perform safety audits and inspections, toolbox talks; participation in HSE meetings with management. Elaboration of Standard operating procedures for safety reasons. Request to contractors to follow terms given in the operation contract, in accordance with the conditions established on it. • Performing activities for new facilities design with contractors: Water treatment and injection, crude oil treatment, quality assessment, equipment and material specifications (pipes, valves, fittings, coatings, flow measurement instruments, separators, chemical dosage systems, walnut shell and multimedia filters, mixers, automatic samplers, storage tanks, oil dehydrators, manifolds, effluent treatment systems, pumps, IAF, DAF, air compressors, pig launchers, receivers). Translation of brochures and technical content.• Elaboration of terms of reference and preparation of proposals for materials procurement and engineering services, contacting suppliers from the contact list for marketing information about equipment and services according to the priorities established in the project cycle. Show less

Chemical analysis of raw materials, supplies. Elaboration of technical reports, technical assessment referred to chemical products uses and handling.

Assessment focused on fuel markets and technology to process natural gas and turns it into SynGas - Synthesis Gas using steam reforming, partial oxidation, autothermal reforming as an intermediate step, and separation equipment such as molecular sieve systems, CO2 membranes, Amine and TEG systems. In order to study the process to obtain Syncrude, it was conducted a research about the Fischer - Tropsch process - Gas to liquid (GTL) and it considered the options to locate a Gas plant to process… Show more Assessment focused on fuel markets and technology to process natural gas and turns it into SynGas - Synthesis Gas using steam reforming, partial oxidation, autothermal reforming as an intermediate step, and separation equipment such as molecular sieve systems, CO2 membranes, Amine and TEG systems. In order to study the process to obtain Syncrude, it was conducted a research about the Fischer - Tropsch process - Gas to liquid (GTL) and it considered the options to locate a Gas plant to process Bolivian Gas and its economical evaluation. Show less

• Wastewater characterization (COD, BOD, oil content, Suspended solids). Field work and job site visits to companies to assess processes applied in wastewater treatment and design parameters for aerobic ponds, facultative lagoons and mechanical plants. Seawater analysis and sampling in sewer networks.• Assistance in sampling protocols, writing reports, gathering information, content and procedures applied in wastewater treatment plants, freshwater sources and water storage facilities… Show more • Wastewater characterization (COD, BOD, oil content, Suspended solids). Field work and job site visits to companies to assess processes applied in wastewater treatment and design parameters for aerobic ponds, facultative lagoons and mechanical plants. Seawater analysis and sampling in sewer networks.• Assistance in sampling protocols, writing reports, gathering information, content and procedures applied in wastewater treatment plants, freshwater sources and water storage facilities. Sampling protocols applied in houses and assigned locations. Instrumental techniques applied to determine water parameters (Spectrophotometry, turbidimetry, TDS measurements, pH, DO, residual chlorine), physicochemical analysis (Hardness, alkalinity, iron, sulfates, chloride, nitrates, nitrites, etc.). Show less