Gregory Wrobel Email & Phone Number

Rochester, New York Area

Perform EMC/EMI testing for MKS amplifier products. Performed emissions and immunity testing and troubleshooting on high power amplifiers for worldwide test standards. Including IEC/EN 61326 and IEC/EN 61000-6-2. Worked with a variety of EMC test equipment including spectrum analyzers, signal generators, receivers, power meters, oscilloscopes, multimeters.

Rochester, New York Area

Perform EMC/EMI testing for MKS amplifier products. Performed emissions and immunity testing on high power amplifiers for world wide test standards. Worked with a variety of EMC test equipment including spectrum analyzers, signal generators, receivers power meters, oscilloscopes, multimeters, antennas and amplifiers from 150KHz up to 1GHz.

Rochester, New York Area

Checkout and inspect various military hand held radios. Visual and functional checkout including transmit and and receive power levels. Trouble shoot and repair radios to the circuit board level. Program radios with automated test fixtures.

Endicott, NY

Performed MIL-STD-461 testing and report preparation for BAE Systems. Testing included emissions and susceptibility testing for MIL-STD-461E and MIL-STD-461F.Performed RTCA/DO-160 testing and report preparation for BAE Systems. Testing included emissions and susceptibility testing for RTCA/DO-160F and RTCA/DO-160G.Worked with a variety of EMC test.

• Performed EMC Compliance testing and issued reports for products for Europe (CE), USA (FCC), Canada (IC), Taiwan (BSMI) Japan (VCCI), Australia/New Zealand (C-Tick), Korea, and other counties using IEC and other.
• Performed MIL-STD-461 testing for clients.
• Performed RTCA/DO-160 testing for clients.
• Worked with a variety of EMC test equipment including spectrum analyzers, signal generators, receivers power meters and network analyzer from 9KHz up to 40GHz.
• Responsible for the EMC test equipment calibration/coordination and calibration database updating.
• Some On-site EMC testing at customer locations.

• Support Kodak Business units of Graphics Communications, Consumer Products, Document Imaging, Inkjet and Health Group for EMC Compliance Certification.
• Wrote products compliance test plans for product testing for Europe (CE), USA (FCC), Canada (IC), Taiwan (BSMI) Japan (VCCI), Australia/New Zealand (C-Tick), Korea (MIC) & China (CCC).
• Perform EMC testing, wrote and reviewed EMC Compliance Reports for products for Europe (CE), USA FCC), Canada (IC),Taiwan (BSMI) Japan (VCCI), Australia/New Zealand (C-Tick) and other Counties using IEC and other.
• Issue FCC Document of Conformity, (DoC) letters for products tested and after reviewing of reports, which are performed by other Test labs.
• Reviewed product data plates & Users Manuals for necessary regulatory information.

• Responsible for product testing for Worldwide Electromagnetic Compliance (EMC). Accommodated Kodak's full product portfolio of equipment.
• Evaluated products and perform compliance testing for Europe (CE), USA (FCC), Canada (IC), Taiwan (BSMI) Japan (VCCI), Australia/New Zealand (C-Tick) and other Counties using IEC standards.
• Prepare reports for worldwide EMC Compliance.
• Coordinate product scheduling and testing for the EMC testing in the Regulator Compliance Center (RCC) for Kodak.
• Performed Normalized Site Attenuation for Kodak’s OATS Test Facility
• Performed Uniformity Measurements in anechoic chambers required for immunity testing.

• Strong technical knowledge of the full product. Responsible for Output Accessory support for the Digital Copier - Printer family of products. This includes the Kodak 1575, 1580, and ImageSource 70cp Copier-Printer..
• Efficiently resolved Copier and Printer problems with Field Engineer daily on Technical Assistance Center (TAC) to improve customer satisfaction.
• Planned for product launch of enhanced product. Including documentation,writing diagnostics, parts planning, training and corrective action.
• Presented product improvement seminars to Field Engineers throughout the country to improve product knowledge.

• Supported copier and printer development from early product development to shipping approval. Committed team player.
• Assisted design engineering on early product development.
• Supported product testing during all phases of evolution from inception, through software development, regulatory, environmental, product announcement and customer availability