Hal Jenson Email & Phone Number
Who is Hal Jenson? Overview
A concise factual answer block for searchers comparing this professional profile.
Hal Jenson is listed as Project Engineer and Manager at General Atomics, a with 1793 employees, based in San Diego, California, United States. AeroLeads shows a matched LinkedIn profile for Hal Jenson.
Hal Jenson previously worked as Project Engineer / Technical Lead / Project Manager / Cost Account Manager / Manufacturing Engineer at General Atomics and Product and Manufacturing Engineer at Veridiam. Hal Jenson holds Master Of Engineering - Meng, Aerospace Engineering (Aerodynamicsastronautics), 3.75 from San Diego State University.
Email format at General Atomics
This section adds company-level context without repeating Hal Jenson's masked contact details.
Review company-level records connected to Hal Jenson before choosing the right outreach path.
About Hal Jenson
Hal Jenson is a Project Engineer and Manager at General Atomics.
Hal Jenson's current company
Company context helps verify the profile and gives searchers a useful next step.
Hal Jenson work experience
A career timeline built from the work history available for this profile.
Project Engineer / Technical Lead / Project Manager / Cost Account Manager / Manufacturing Engineer
Water Twister MOD-II Development and Production, concurrent• Project Engineer, responsible for customer interface, budget, schedule, technical scope• Coordinated parallel design and manufacturing efforts to reduce ~$10M design risk at sole source supplier• Communicated with technicians through executive, and customers• Delivered two CSI (Critical Safety Item) housings, ~$5M, before competition’s first delivery,despite award ~13 months after competition, to NAVSEA specifications• Responsible as CAM (Cost Area Manager) and technical lead• Provided weekly, monthly briefs on cost performance, technical risks to program office• Led Fixed Firm Price proposal of ~$90M for carrier retrofit, while sill in design• Managed IMS (Integrated Master Schedule)• Utilized Earned Value ManagementMojave IRAD• Led Mojave structural team for composite, bonded aircraft, a Prototype XRev FAR-23 (Federal Aviation Regulation)• Coordinated design, tooling, manufacturing teams from prior to SRR, to PDR CDR through successful structural test in under 18 months• Developed low cost tooling solution, easily modifiable for rapid development of composites• Reduced risk by early identification and mitigation through representative manufacturing andtest samples• Maintained weight and balance budgets between structural design teams from SRR to CDRSky Guardian, IRAD• Led structural Test Readiness Review prep and execution• Inherited, tracked and resolved cost overruns, and advocated for practical solutions, resultingin use of commercial solutions, saving ~$500kAvenger, IRAD and Contract• Inherited, led and focused engineering, planning, manufacturing teams during~$10M repair effort of composite bonded centerwing• Prevented repeat structural failure• Organized concurrent airframe, field retrofit builds resulting in a documented configuration• Completed incorporation of major design changes for Predator during concurrentbuild and ERP (Engineering Resource Management) release
Product And Manufacturing Engineer
Various Products• Wrote and lead team to perform Installation Qualification (IQ), Operation Qualification (OQ) and Performance Qualification (PQ) for various surgical and medical robot products• Interpreted contract and drawing requirements into formal manufacturing, scheduling, finance and quality plans• Troubleshot custom tooling and processes to raise first pass yield from under 50% to over 90% on NQA-1 (Nuclear Quality Assurance) hardware• Utilized SPC (Statistical Process Control) to increase yield to improve profit margins on medical device manufacture• Developed and wrote work instructions, company operating procedures, Failure Modes and Effects Analysis (FMEA), Manufacturing Quality Control Plans (MQCP), Corrective Action Reports (CAR), • Reduced ~1/3 of touch labor on legacy product line through optimization of workflow
Technical Engineer Ii And Tech Writer
Commercial Aircraft 737, 747, 767, 787• Utilized BOM (Bill of Material) and SOP (Standard Operating Procedures) data for writing of Aircraft Maintenance Manual and Fault Isolation Manual procedures for landing gear• Documented rigging procedures of landing gear doors for Boeing commercial aircraft• Wrote Component Maintenance Manual for ailerons and other flight control surfaces
System Test Engineer
• Designed and drafted adjustable support system to for engine test cell, with the ability to change test engine configuration• Calculated margins, matched shear and moment on variable configurations for competition's engine, to support aftermarket competition
Colleagues at General Atomics
Other employees you can reach at ga.com. View company contacts for 1793 employees →
Donna Hawley
Colleague at General AtomicsPalm Springs, California, United States
View →
JA
Joshua Amante
Colleague at General AtomicsSan Diego, California, United States
View →
TD
Tony Deaton
Colleague at General AtomicsColorado Springs, Colorado, United States
View →
LC
Lane Carlson
Colleague at General AtomicsSan Diego, California, United States
View →
KF
Kevin Franco
Colleague at General AtomicsSan Diego Metropolitan Area, United States
View →
LL
Limin Liu
Colleague at General AtomicsSan Diego, California, United States
View →
JS
John Schab
Colleague at General AtomicsLas Vegas, Nevada, United States
View →
DW
Dale Wells
Colleague at General AtomicsMurfreesboro, Tennessee, United States
View →
CS
Chad Smith
Colleague at General AtomicsWaterford, Mississippi, United States
View →
RB
Richard Boonstra
Colleague at General AtomicsGrand Rapids, Michigan, United States
View →
Hal Jenson education
Master Of Engineering - Meng, Aerospace Engineering (Aerodynamicsastronautics), 3.75
Bachelor Of Science In Engineering, Mechanical Engineering, 3.0
Frequently asked questions about Hal Jenson
Quick answers generated from the profile data available on this page.
What company does Hal Jenson work for?
Hal Jenson works for General Atomics.
What is Hal Jenson's role at General Atomics?
Hal Jenson is listed as Project Engineer and Manager at General Atomics.
Where is Hal Jenson based?
Hal Jenson is based in San Diego, California, United States while working with General Atomics.
What companies has Hal Jenson worked for?
Hal Jenson has worked for General Atomics, Veridiam, Boeing, and Pratt & Whitney.
Who are Hal Jenson's colleagues at General Atomics?
Hal Jenson's colleagues at General Atomics include Donna Hawley, Joshua Amante, Tony Deaton, Lane Carlson, and Kevin Franco.
How can I contact Hal Jenson?
You can use AeroLeads to view verified contact signals for Hal Jenson at General Atomics, including work email, phone, and LinkedIn data when available.
What schools did Hal Jenson attend?
Hal Jenson holds Master Of Engineering - Meng, Aerospace Engineering (Aerodynamicsastronautics), 3.75 from San Diego State University.
Search by job title, company, industry, location, and seniority. Export verified B2B contact data when you need it.
Start free trialCheck these profiles if this is not the Hal Jenson you were looking for.
View similar profiles