Jamie Mac Email & Phone Number

Menlo Park, Ca, Us

Minneapolis, Mn, Us

• Monitor, investigate, and address quality issues related to customer complaints.• Manage and monitor suppliers on the Approved Supplier List (ASL) through periodic audits and supplier metrics assessment.• Drive supplier corrective actions (SCARs) to resolve systemic issues.• Conduct investigations, propose action plans and verify effectiveness of actions taken in relation to CAPAs.• Perform risk evaluation, investigation, disposition, correction, and verification activities on nonconformances.• Review and revise process, use, and design Failure Mode and Effect Analysis (FMEAs) as a result of input from process changes, design changes, or input from customers.• Provide monthly and quarterly quality metrics to customers.• Monitor the performance of the ISO 14644-1 Class 8 cleanroom via quarterly cleanliness monitoring, periodic cleaning, and daily pressure verification.• Drive completion of manufacturing site relocation activities related to relocation of equipment, manufacturing process validations, and controlled environment validations.

Palo Alto, Ca, Us

• Determine and evaluate key performance indications (KPIs) to monitor the incoming inspection department.• Develop a dashboard for data visualization of incoming inspection KPIs.• Assess and review measurement routines created by inspectors to ensure robust and repeatable measurements accurate to the GD&T dimensions.• Assign inspection plans for incoming material with respect to the material drawing.• Communicate company measurement methodology to manufacturing engineers and suppliers to gain alignment and how best to accurately represent the parts being measured.• Conduct measurement offset studies between Varian and Suppliers to determine which dimensions were being measured differently.• Participate in Material Review Board meetings to determine the appropriate actions to be taken with non-conforming material.• Wrote a quality plan to outline the steps to validation of existing measurement routines.• Outline process FMEA to assess the possible failures which can occur during the incoming inspection process.• Perform test method validations for measurement routines executed on CMMs and optical measurement systems.• Create inspection routines for Keyence IM-7030, Smartscope Quest 800, and Zeiss Contura to measure CTQs.• Conduct focused audit on suppliers’ in-process and final inspection processes.• Implemented 5S methodology in new inspection lab layout to optimize material flow.• Reduced inspection time and defect rate for a family of parts as part of a company Green Belt project.

Scottsdale, Arizona, Us

• Designed fixtures to be used during in-process and final inspection of features critical to quality of manufactured parts.• Created semi-automated and automated Micro-Vu, Seebrez, and Nikon measurement programs for inspection of CTQs to be used as an in-process and final inspection of manufactured parts.• Performed measurement system analysis on measurement routines using Gage R&R and Gage Offset.• Wrote test method validation protocols and reports for the validation of test methods using Coefficient of Variance, Attribute Study, ANOVA (Nested Gage R&R) and ANOVA (Crossed).• Evaluated the effectiveness of custom Go/No Go fixtures using Attribute Studies• Wrote IQ/OQ/PQ protocols and reports for optical measurement systems and burst/leak testers.• Created inspection programs for a Keyence TM-3000 Optical Micrometer to measure multiple CTQs in one program.• Performed gap analysis comparing current company test methods with provided customer test methods.• Conducted FMEA on a product line experiencing a high amount of failures during final acceptance to determine root cause of manufacturing defects.• Provided root cause analysis feedback based on measurement data to manufacturing and process engineers.• Assessed customer drawings using GD&T and negotiated which features were to be inspected as CTQs.• Created detailed work instructions to allow operators to use hand tools, custom inspection fixtures, and automated and semi-automated inspection routines on various manufactured parts.• Implemented process changes as result of SCARs and internal CAPAs.• Trained operators on proper execution of work instructions and test methods.• Analyzed manufacturing data using JMP and Minitab to determine the change in CTQs experienced by each step of the manufacturing process to assist other process engineers with their DoE studies.

Denver, Colorado, Us

Performed site assessment, structural and foundation mappings, and post-construction reinforcement inspections on cellular sites.Generated reports detailing issues, observations, and work completed for each scope of work.

Milpitas, California, Us

• Created Solidworks models of different prototype tooling fixtures• Conducted SPC Analysis on data gathered from the automated manufacturing process.• Interpreted drawings of incoming parts to verify company received parts within specifications.• Performed experiments to verify the root cause of defects found during manufacturing process.• Wrote and revised work instructions and product specifications and then trained operators to the new changes.

• Surveyed the current form factors of wearable head-mounted electronics and health monitoring systems.• Designed several prototype form factors for a wearable health monitoring system with Autodesk Inventor.• Created layout of electrical components for each form factor.• Selected components for a sensor array that would allow for position tracking and health monitoring.• Performed functional tests of GPS components to determine the effect of tree and building cover on position tracking.

• Manufactured cathode and anode materials for coin cell batteries.• Conducted validations tests on new cathode materials for lithium-ion coin cell batteries.• Wrote work instructions for the visual inspection and manufacture of cathode and anode materials.• Conducted statistical analysis on the results of the validation tests and generated report.• Researched and executed a procedure to create and test supercapacitors.• Trained another intern to manufacture cathode materials and batteries as well as to conduct validation tests.

Rancho Santa Margarita, Ca, Us

• Designed a tool to cut off hardened plastic lips of heat bonded plastic sleeves.• Designed Solidworks test fixtures for new products that validate their efficiency.• Conducted tests to validate new products and assembly line methods.• Created Solidworks drawing files to document changes of tools and tooling fixtures.• Oversaw the conduction of product validation tests done by engineering technicians.

Rancho Santa Margarita, Ca, Us

• Used Solidworks to design a tool to improve the efficiency of the assembly line.• Improved the design of an existing tooling fixture to cut heat shrink tubing consistently.• Used Solidworks to model tooling fixtures and to design test fixtures.• Created Solidworks drawing files to document changes of tools and tooling fixtures.• Oversaw the conduction of product validation tests done by engineering technicians.• Applied statistical analysis and generated reports of the results of the product validation tests.

Master’S Degree, Mechanical Engineering

Bs, Mechanical Engineering, Material Science

Bachelor Of Science, Mechanical Engineering