•Prepare & Review all engineering documents including Scope, MR, NMR and IFC.•Develop instrument indices and lists such as instrument index, I/O list, instrument range, and alarm set points as per client requirements and process documents.•Familiar with ISA, ISO, ANSI, IEC and SAES Standards.•Provide design assistance during the development of P&ID, Cause and Effect and Control Narrative.•Provide design assistance in the identification, sizing, selection and procurement of field… Show more •Prepare & Review all engineering documents including Scope, MR, NMR and IFC.•Develop instrument indices and lists such as instrument index, I/O list, instrument range, and alarm set points as per client requirements and process documents.•Familiar with ISA, ISO, ANSI, IEC and SAES Standards.•Provide design assistance during the development of P&ID, Cause and Effect and Control Narrative.•Provide design assistance in the identification, sizing, selection and procurement of field instrumentation including control valves.•Develop and prepare MS,MTO, JSA, Loop package, Energisation and start-up procedure.•Review and approve Technical Bid Evaluation (TBE) for all project field instrumentation including Control Valves, MOV, On-Off Valve and Fire and Gas Detection and assure technical compliance to Saudi Aramco standards and project specification.• Provide technical support to project management activities, procurement and project controls through all project cycle and answer Technical Queries raised by Contractor when required.•Attend Factory Acceptance Test (FAT) of the Process Control System and resolve any technical issue prior of shipment to site.•Conduct Site Acceptance Test (SAT) and Integration Site Acceptance Test (ISAT) for all Process Control Systems.•Field Instrumentation Documents: P&ID, ILD, and Hookup Drawings, Loop Checking, Commissioning.•Understanding & troubleshooting of P&ID and ILD diagram, Hookup diagram, Loop wiring diagram, Instruments specification sheets and control panel drawing, JB details & cable layout drawing.•Suggests new means of improving the performance and lifetime of the instruments and control equipment.•Construction and Pre-commissioning of MV Transformer•Construction and Pre-commissioning of MCC (Including Busbar)•Construction and Pre-commissioning of Switchgear (CB testing) with Aramco PID.•UPS and Battery installation and Pre-commissioning.•Construction and Pre-commissioning of Fibre optic system. Show less

• Coordinate activities and resolve issues among proponents, contractors and other parties to allow construction activities to progress according to plan and the final completion.• Performed SAT for around 70 panels with Proponent and vendors in 5 PIBs.• Troubleshooting, supporting vendors for configurations in DCS, ESD and all FF and analog transmitters.• System handled are Yokogawa Centrum system DCS, ESD Profibus system, GE CCS and MPS system with vendors for pre loop check.•… Show more • Coordinate activities and resolve issues among proponents, contractors and other parties to allow construction activities to progress according to plan and the final completion.• Performed SAT for around 70 panels with Proponent and vendors in 5 PIBs.• Troubleshooting, supporting vendors for configurations in DCS, ESD and all FF and analog transmitters.• System handled are Yokogawa Centrum system DCS, ESD Profibus system, GE CCS and MPS system with vendors for pre loop check.• Almost complete 10000 final loops with proponent in 5 trains in these plant and supporting Saudi Aramco for commissioning and start-up activities in 2 trains.• Installation of Fire protection Systems like smoke detectors, heat detectors, beam detectors, interface module, horn, strobes and beacons in all buildings and structures.• Pre-commissioning and commission of fire alarm system with other system as per cause & effect with the programmers from both sides.• Prepare TQs as per the standard.• Prepare spare parts list for all the panels and the devices related to fire alarm system.• Involved in construction activities like erection of conduits, trenching, cable laying, and installation of instruments such as transmitters, switches, gauges, and control valves. Installation of Electrical equipment like generators and transformers and lighting systems.• Installation of Fire Alarm Systems like detectors horns and beacons in all buildings and structures. Show less