Jose Antonio Peña Sequera Email and Phone Number

CRISP PROJECT TR-ExxonMobil:Visual inspection for complete and correct installation. • Cleaning, flushing, pressure and leak testing of pneumatic and hydraulic tubing. • Function testing of control systems. • Area completion. Commissioning Documentation Preparation & Handover Following are the documentation is prepared before the startup or at the end of commissioning and to be handed over once the commissioning process has been completed. Engineering Documentation• Vendor Lists• Vendor Manuals including all vendor documents/drawings, Contractor Commissioning and Start-Up plans (CSU) and Operating Manuals• Commissioning Spares Lists• Valve Lists• Cause and Effects Charts• Trip Register/Schedule• System P&IDs• Punch points list. Fire Alarm System Commissioning Final Documents for Commissioning After the successful completion of all pre-commissioning activities, the following list of final documents should be available readily for the commissioning activities. System P&ID’s• isolation register• System cleaning procedures• Hazard Study and actions• Equipment Check Sheets, off and on-site checks• System Punch lists• Action upon Alarm Sheet• Handover Certificate Construction/Maintenance to Commissioning• Project documentation check sheet prior to the introduction of safechemicals• Safe Chemical Commissioning authorization and Pre-commissioning Procedures• Leak Test Checklist and Procedures• Instrument Check Sheet• Motor Check Sheet• Interlock Check procedures• Emergency Shut Down System check procedures• DCS sequence test procedures• Relief Stream Check Sheets• Critical Insulation Checks• Critical Gasket Installation Checks• Lubrication Check Sheet• PSSR, Plant Check-out prior to the introduction of Hazardous Chemicals• Documentation Requirements for Ongoing Maintenance Group• Authority to Introduce Process Chemicals, check sheet & Certificate• Commissioning Procedures• Standard Operating Procedures• Commissioning to Plant Handover Certificate

Supporting activities from pre-commisioning, commissioning and initial start-up and normal operations in the units, slug catchers, crude desalters, crude degassing, crude stabilization, sour gas sweetening, amine units, Glycol systems, gas dehydration units, gas, and water injection systems. Compression system: The gas is compressed in three stages from a pressure of 26.3 barg to 414 bargEach first stage is rated for 153.88 MMSCFD while each second and third stage is rated for 140 MMSCFD.Dehydration system: Design Capacity of each unit is 151.3 MMSCFD, after content of 2 lb/MMSCF maximum. The glycol used shall be triethylene glycol (TEG) at 99.95wt%.Responsible for a safe, economical, and trouble-free operation and safe emergency handling of the production facilities by providing effective leadership and coordination among the Production Units and other Departments. Also responsible for implementation of the company HSE policy and Companies Oil / Gas production, Processing and Water Injection targets. To review PTW and attend daily permit meetings. Monitors Chemical Injection Systems and carries out some Lab Tests to ensure required Water Quality and Quantity are achieved. GTG’s, UF, SWRO, Utilities unit, PSA Nitrogen generation, Fire water system, Instrument and plant air, SWF.Competence areas:• Supervision• PTW• SAP Work Order, WO, Material request MR• Budgets• Policies, systems, processes & procedures,• Performance management• Innovation & continuous improvements• Health, safety, environment, and sustainability• Report

Supporting activities for commissioning, initial start-up and normal operations in the units, slug catchers, crude desalters, crude degassing, crude stabilization, sour gas sweetening, amine units, Glycol systems, gas dehydration units, gas, and water injection systems.

Spie Oil and Gas Services at Project Sadara Isocyanates Saudi Aramco Dow Chemical Jubail Kingdom Saudi Arabia as Commissioning SpecialistSupporting for commissioning and initial startup of the block corresponding to Isocyanates, Toluene diisocyanate (TDI) and Diaminotoluene (TDA). Monitoring functional testing, commissioning of utilities, testing links, pump testing, cleaning and flushing the systems and sub-systems, leak test, dry-out refractory, boil-out, chemical cleaning, degreasing, review and preparation of commissioning procedures, initial startup, normal operations, operational emergency.

Supervisor support for commissioning and initial startup of the block corresponding to gasoline, sulfur and DHT EPC. Monitoring functional testing, commissioning of utilities, testing links, pump testing, cleaning and flushing the systems and sub​​-systems, leak test, dryout refractory, boilout, chemical cleaning, degreasing, review and preparation of commissioning procedures, initial startup, normal operations, operational emergency .

In charge of training new operators of areas of utilities, off site and tank farm, also the redaction of the training manuals, guidelines, monitoring and evaluation of the performance of trainees. I also contributed to the verification activities Commissioning, punch lists, identification of deficiencies in the construction of systems utilities, offsite and tank farm, as well as DHT, NHT, DCU, Sulfur blocks and units which the project asking me for support.

Provide connection or nexus between the different specialties to ensure the reliability of the processes and equipment. Through the identification of equipment and critical processes fostering a unique and handy language between specialties to facilitate the use of data obtained to another different engineering, based on tools used in engineering processes: KPI's, HAZOP, RCA , Lesson Learned, trends and different software that allow us to monitor the process units, so that the data obtained with these tools together with SAP, RBI, Taxonomy, administration of data critical, quality management and maintenance to get the proper plan for equipment or systems to established expected failure modes.Also define the equipments to be monitoring, based on criticality evaluated on managing the database. Finally define the flow of information collected through condition monitoring recommendations for intervention and decision-making by the executing and maintenance area.

Special assignments in PMT Technip Roma- Italy: supporting the Basic engineering, PI&D and PFD review, HAZOP and FEED of new project Petrocarabobo Upgrader Shareholders PDVSA-REPSOL - Indian Oil – PETRONAS.

Leader Process Engineer in Utilities & off Sites. I am in charge of 10 units that give the necessary supply for the Upgrader which generates 180KBPSD, in a base case design. However after started up and tested it has eventually increased the production until 200KBPSD and in that way all the supplies were increased by demand. The plants is divided in; cooling water, Fresh water, drinkable water, Boiler feed water, steam generation, Plant air and instrumentation air, gas supply to pilots and fuel gas systems, Nitrogen supply, electrical substations, Fire water system, served and oily waters treatment, flare, intermediate storage, final storage of product and shipment.

Continuous monitoring of all process variables of the unit, preventing and correcting any deviations that may impact the continued operation or to specifications and product quality by issuing timely effective recommendations. Participate in the identification of problem areas or operational areas requiring changes or modifications of a technical nature. Comply with and / or initiate studies of process changes and implementation of process improvements.Monitoring the operation of equipment such as pumps, heat exchangers, furnaces and columns. Prepare tests in order to find fault and / or malfunction and solve operational problems.Ensure compliance with operational guidelines and laboratory analysis, alerting any deviation detected and participating in its correction.Continuous updating all indicators related to food processing plant, empty drums, etc, that allow economic evaluations and profitability calculations complex.Prepare performance summaries based on information received from operations and other departments, detailing process performance and associated facilities.Updating files, P & ID's, procedures and any process and / or safety information as required.Provide proper use and maximum benefit from all the resources available in the organization.Perform alternative analysis, developing process specifications and recommendations to the efficient use of all available equipment of the unit.Detect any possibility of increasing the profitability of the unit, by considering process optimization: capacity, operating costs and product disposal.During periods of plant shutdown, participate in the verification of equipment conditions and evaluate possible changes or improvements if applicable.Provide assistance in the preparation of the work list for scheduled shutdowns (Major Turnaround).

Control Room / Panel Operator of Sincor Upgrading Utilities & Offsite 01/02/2003 to 31/12/2007.•Control Room & Panel Operator in Upgrading/Utilities & Offsites•Commissioning, start up, normal operation and shut down of a DCS & Foxboro I/A System and a ESD Triconex system•Unit Shut Down (February 2.004./15 days) and (October 2.004./55 days)•Complete Unit Start Up.( Utility Water, Potable Water, Demine Water, Boiler Feed Water (BFW), Steam Generation, Nitrogen, waste water system and Tank farmEquipments Certification altogether with the vendor these activities were focused to guarantee the main safety characteristics in equipments like Boilers, compressors, furnaces etc.I cover the charge as a Field Team leader supporting all the field operation and the news field operators also as Shift supervisor.Field operator for Utilities and Offsite: 01/11/2001 to 01/02/2003 On Job Training on Utilities & OffsiteCommissioning.Start-up of the following Systems: Utility Water, Potable Water, Demineralization Water, Boiler Feed Water (BFW), Steam Generation (400t/h boilers)Tank farm operations 2x550 Kbblds, 2x 80 Kbblds 3x 30 Kbblds 1x 127 Kbblds Intermediate storage & 5x 550 kbblds Final 1x 750 kbblds product storage. Waste Water Treatment Plant Operation (WWT) (760 ton/h), this effluent meets international specs and it is directed to the sea. Pre-Commissioning, Commissioning, preparation of the Operational Procedures start up, normal operations and shut down of vacuum. Residue/Synthetic crude Blender cooler unit to satisfy a niche market of Syncrude with bottoms.JOB Training as Field Operator Delayed Coker Unit 01/01/2000 to 08/31/2001.

Operator of Ironing process for making aluminum containersSampling for Process Continuous MonitoringTrimmer OperatorQuality control in the manufacture of aluminum cansMonitoring of cans thicknessAnalysis of mechanical resistance of the canPreventive and corrective maintenance of diesPrecision Mechanical

To program, to direct and to control the productive process based on the requirements of productivity and yield, assuring the quality standards demanded and administering efficiently the human and material resources according to the aims of the organization. Likewise, to collaborate with the constant improvement of the infrastructure and of the processes.Laboratory analyst Asphalt analysis Fluid point Hardness & Hardness Point Tri Chloral Ethylene Solubility Cold Resistance Hot ResistanceRC2-Asphalt Analysis Fluid point Hardness & Hardness Point Cold Resistance Gasoline & Kerosene Analysis