Detailed Education and Knowledge in the following areas:- Industry Standard Safety Practices.- Ohms Law in Series, Parallel, and Combination Circuits.- Schematics and Ladder Diagrams.- Electrical components, including: Resistors, Capacitors, Inductors, Diodes, and Transistors.- RC and RL Circuits.- Use of Low Voltage to control High Voltage through Relays/Contactors.- The principles of AC Induction Motors and DC Motors 12 VDC through 208 Three-Phase.- AC and DC Motor Control through Pulse Width Modulation and Variable Frequency Drives.- General knowledge of Programmable Logic Controllers (PLC's) and Programming.- Soldering techniques.- Use of machinist tools, including: Drill Press, Manual Sheet Metal Shear, Manual Press Break, Metal Lathe, End Mill, Tourette Punch, Micrometers, Vernier Calipers, as well as various general hand tools.- Understanding and adherence to requirements for Personal Protective Equipment (PPE), along with "Lock Out-Tag Out" procedure.- SolidWorks 2011- Oxy Acetylene Welding/Cutting- SMAW-Shielded Metal Arc Welding- GTAW-Gas Tungsten Arc Welding- GMAW-Gas Metal Arc Welding

- California State Certified Fire Life Safety Journeyman Technician #141439- Hochiki Certified- Sielox Access Control Certified- Hilti Fire Stop Certified- Understanding of NFPA 72 and NFPA 70/NEC- Installed Fire Alarm Circuits: NAC, SLC, IDC, Door Control- Worked in areas of strict regulations, including: U.C. Davis Medical Center, Sacramento International Airport, Freemont-Rideout Health Group, AT&T, Jackson Laboratories-West, and California Department of Corrections and Rehabilitation.- Worked on various systems, such as Siemens, Notifier, Firelite, Hochiki, Kidde, and EST.- Examined systems to locate problems, such as loose connections or broken insulation.- Tested backup batteries, keypad programming sirens, and all security features in order to ensure proper functioning, and to diagnose malfunctions.- Fed cables through access holes, roof spaces, and cavity walls to reach fixture outlets; then positioned and terminated cables, wires and strapping.- Inspected installation sites and studied work orders, building plans, and installation manuals to determine materials, requirements, and installation procedures.- Adjusted sensitivity of units bases on room structures and NFPA 72 specifications.- Tested and repaired circuits and sensors, and wired to NFPA 70 and NFPA 72 specifications.- Drilled holes for wiring in wall studs, joists, ceilings, and/or floors.- Demonstrated systems for customers and explained details, such as the difference between Trouble, Supervisory, and Alarm conditions.

- Completed multiple jobs independently from start to finish in a clean and timely manner.- Managed jobs as well as built excellent work relationships with onsite supervisors of other general contractors and subcontractors.- Measured and marked surfaces to lay out work, according to blueprints/drawings.- Read blueprints and other specifications to determine methods of installation, work procedures, and/or material and tool requirements.- Hung lasers to temporary wall moldings to guide positioning of main runners.- Assembles/Installed metal framing.- Fit and fastened wallboard/drywall into position on wood and/or metal frameworks.- Hung drywall panels on metal frameworks of walls and ceilings.- Spread joint compound between boards and/or panels, or over cracks, holes, nail heads, and/or screw heads.- Pressed taper over joints to seal.- Spread and smoothed topping compound over tape, using trowels to blend joints with wall surfaces.- Removed extra compounds after surfaces were covered sufficiently.- Sanded and/or patched nicks and/or cracks in plasterboard and/or wallboard.- Patched holes and wall openings, and then matched and blended various textures on existing wallboard.

- Reviewed plans and bid jobs according to field conditions.- Made contacts with various property management companies and subcontractors to coordinate job scheduling.- Analyzed blueprints and other documentation to prepare time, cost, materials, and labor estimates.- Prepared estimates for use in selecting vendors and subcontractors.- Communicated and conferred with engineers, architects, owners, contractors, and subcontractors on changes and adjustments to cost estimates.- Prepared estimates used by management for purposes, such as planning, organizing, and scheduling work.- Reviewed material and labor requirements to decide whether it was more cost-effective to purchase, or rent machinery.

- Set concrete forms and placed/finished concrete to ADA specifications.- Cleaned and organized all tools and materials on a daily basis.- Checked forms to ensure that they were properly constructed.- Spread, leveled, and smoothed concrete using rake, shovel, and or power trowel, hand or power screed, and float.- Monitored how the wind, heat, and/or cold affected the curing of concrete during the entire process.- Produced rough concrete surface using broom.- Molded expansion joints and edges using edging tools, jointers, and straightedge.- Cleaned chipped area using wire brush and felt, and observed surface to determine if rough or uneven.- Signaled truck driver to position truck to facilitate pouring concrete, and moved chute to direct concrete on forms.- Applied hardening and sealing compounds to cure surface of concrete, and waterproof, or restore surface.

- On site foreman on Commercial Tenant Improvements.- Knowledge of all carpentry skills, wood, and metal.- Scheduled field Inspections.- Kept jobs on schedule with communication through subcontractors and property managers.- Worked under strict regulations in Dental offices and U.C. Davis Medical Center.