Matt Koch Email and Phone Number

Currently working on Maersk deliverer.Working the rig floor, tripping pipe in and out of hole.Running mud pumps.

Work on drill floor whilst running in/ out of hole, drilling operations and third party operations.➢ Assist in subsea department, whenever time permits.➢ Undertake simple maintenance in the subsea department as instructed by subsea engineer, aswell as grease and maintain choke and kill manifold on drill floor.➢ Participate in Risk Assessments, and writing JSA's.➢ Inform the Driller, Assistant Driller regarding unusual/unsafe situations around work areas.➢ Assist in the training of Roustabouts, when relieving or new on the drill floor.➢ Participate as a member of the Risk Assessment Team.➢ Perform maintenance work on the drilling equipment and on the drill floor.➢ Carry out work in the Shaker Room and maintenance of all equipment used for cleaning mud.➢ Perform daily cleaning and clearing up on the drill floor and in the shale Shaker Room.➢ Carry out daily inspections of the derrick structure.➢ Lubricate drilling equipment as instructed by Supervisor➢ Take and record mud weights and viscosity whilst working in the shale shakers.➢ Comply with Permit to Work System.

➢ Complete work offshore in Australia, as well as Asia Pacific Region, when required.➢ Completed all required in-house QHSE training.➢ Packaging and preparing equipment for load outs to shore based client holding yards, and offshore well site locations.➢ Managing of pre-job checks prior to running casing.➢ Carried out preventative maintenance of casing running equipment, and also trained new employees.➢ Supervised trainees while they performed maintenance of tubular handling equipment, power tongs and Hydraulic Power Units.➢ Familiar with Job Safety Analysis procedures, as well as writing site specific JSA’s.

➢ Maintenance of Handling Equipment.➢ Completed all required in-house QHSE training.➢ Packaging and preparing equipment for load outs to shore based client holding yards, and onshore wellsite locations.➢ Running 13-3/8”, 9-5/8”, 7-5/8”, and 7” casing using “Casing Drive System”➢ Maintenance of Casing Drive System components including: disassembly and rebuilding of actuators, changing out of spearhead, mandrel, and grapples, and all other servicing in accordance with documented procedures and checklists.➢ Managing of pre-job checks prior to running casing.➢ Carried out preventative maintenance of Casing Running Equipment, and also trained new employees.➢ Supervised trainees while they performed maintenance of Casing Drive System, and Hydraulic Power Units.➢ Familiar with Job Safety Analysis procedures, as well as writing site specific JSA’s.➢ Able to safely operate Over Head Gantry Crane.➢ Fault finding and troubleshooting of Casing Running Equipment, to minimize the effect of rig down time, when experiencing equipment failures.

➢ Worked up the derrick when running in and/or out of the hole with Drill Pipe, Heavyweight Drill Pipe.➢ Worked in the pit room, doing mud weights, transferring mud from pit to pit, and mixed mud, under the guidance of the Mud Engineer. Also monitored the shakers when drilling.➢ Worked in the pump room performing maintenance on mud pumps, and changing of swabs and liners.➢ Assisting the subsea engineer with maintenance of BOP’s, LMRP, Compensators and other subsea equipment.➢ Running of BOP’s, marine riser, and rucker lines.➢ Working on drill floor with Casing Running and Wireline operations.

➢ Unloading and backloading of tender vessels with the Crane Operator➢ Working in the shakers with the derrickman.➢ Moving equipment around the main deck with the Dogman and Crane Operator.➢ Relieving roughnecks up on the rig floor for meal breaks.➢ Needle gunning, chipping and painting of main decks due to rust.➢ Greasing of jacking motors.➢ Removing and replacing dump valves in pre-load tanks.​