• Work in Dell Display SQE team, take the owner for touch supplier Laibao and part LCD supplier BOE, take the responsibility for Dell commercial 13/14 inch model from RFI/RFQ specification definition to manufacturing ramp up.• In NPI phase, co-work with SDE team to handle qualification issues focus on process relevant problem verification and NPRR documents review to ensure NPI models meet schedule, ensure clean launch and yield ram up. As leading SQE to ensure BOE first model MP… Show more • Work in Dell Display SQE team, take the owner for touch supplier Laibao and part LCD supplier BOE, take the responsibility for Dell commercial 13/14 inch model from RFI/RFQ specification definition to manufacturing ramp up.• In NPI phase, co-work with SDE team to handle qualification issues focus on process relevant problem verification and NPRR documents review to ensure NPI models meet schedule, ensure clean launch and yield ram up. As leading SQE to ensure BOE first model MP successfully in XPS model• New technology/material/process by new material qualification and MRL review, leading Corning new generation glass & AGE feature, metal mesh material with new controller IC/pen solution etc.• Leading supplier quality issue and co-work with ODM, on site verify the defective sample to study any risk impacting from system level including design and process, as the coordinator to pull through issue smoothly to ensure supply chain stability.• Review LCD/Touch full process yield rate during samples preparation by each stage, production line audit, work out finding list improvement plan, come out clearly corrective action to achieve stable quality level from NPI to MP. • Systematically push and help the supplier to improve and optimize process parameter by DOE, AQP and PMP optimization, SPC and CIP project pull through, 5C report and lesson learned review to fully close issue• Leading SQE team NUDD FMEA laboratory project to dig out real process variation factor and failure effect and reason evaluation, optimize preventive and detection method to evaluate risk level• Leading SQE team automation and digitalization project, evaluate supplier level and coverage ratio, study actual impacting for quality performance. Show less

CQE: • Handle the quality issue for optical film, on site study to find solution for iPad mura issue to ensure MP smoothly.• Study the punching process to improve optical film quality issue as punching burr, notch, wave, wrinkle and so on.• Leading factory lean project for DBEF delamination project, align with the customer application requirement to reduce delamination loss ratio with loosen spec to save over $100k per yearAE:• Handle the technical and quality service for… Show more CQE: • Handle the quality issue for optical film, on site study to find solution for iPad mura issue to ensure MP smoothly.• Study the punching process to improve optical film quality issue as punching burr, notch, wave, wrinkle and so on.• Leading factory lean project for DBEF delamination project, align with the customer application requirement to reduce delamination loss ratio with loosen spec to save over $100k per yearAE:• Handle the technical and quality service for optical film and OCA in EVT/DVT/PVT/MP.• In charge of technical support for NPI including VOC collection, technical and application evaluation and co-work with RD team to adjust the parameter for new product in time. • Hold the seminar meeting for technical communication to study the design trend and the request from the customer, lead the new product pull through and application project in China.• Study the design and process trend and enhancement at the customer site, inform and help the manufacture team to study and prepare the process ability to meet the request from the customer. Show less

• Working start from product engineering (PE role), strongly technical knowledge about LCD display principle, raw material character, process flow and QC plan, engage failure analysis & root cause with action plan for yield rate improvement. • New project transfer from mother company to setup local factory NPI process, leading cross functional team to settle down development issue under risk assessment to mass production, including local 2nd source material qualification. • According to… Show more • Working start from product engineering (PE role), strongly technical knowledge about LCD display principle, raw material character, process flow and QC plan, engage failure analysis & root cause with action plan for yield rate improvement. • New project transfer from mother company to setup local factory NPI process, leading cross functional team to settle down development issue under risk assessment to mass production, including local 2nd source material qualification. • According to the strongly technical background, promoted to engineering service department to support customer side including new project development & MP product quality service, ever working for different application field as desktop, notebook, mobile phone customer.• Daily operation for customer production line quality improvement, yield rate collection and define the top failure list for analysis, review/release FACA report to customer side, leading discussion/explanation until issue close to keep continuously input. • Very familiar with 8D report spirit, including risk lot definition, short term containment action, and root cause identification, long term solution with lesson learn/leverage plan. • Hold routine TQR&QQR meeting with customer and drive internal CIP for quality improvement as another function requirement. Show less

• Audit the supplier for their QSA&QPA. Suppliers grade yearly; Visit the excellent vendor; validate the improve actions that the vendor promised.• Help the vendor with poor ability to set up the quality system being fit for the request of the customer.• Have an idea about PCB, FPC, R/L/C, Cable, Connector, IC and so on. Well known about the process for PCBA• Make SIP by the certificate of component to define the method of inspection and relative instrument of IQC.