Michael Rapanut Email & Phone Number

Jubail, Eastern, Saudi Arabia

As a mechanical engineer initiate inspection and review mechanical and vendor drawing based on contract specification, conduct walk down inspection for the installation and alignment of rotating and static mechanical equipment and machinery as per vendor specification. Conduct and supervise inspection in mechanical equipment such as Exchanger, Vessel, Equipment skid, Cooling Module, and Heater Installation and assembly. Punch and clear out any discrepancies and deficiency during walk through, Prepare permit to Work, Drawing detail and general condition of works prior for mechanical and pipe testing. Conduct line checking commissioning P&ID drawing and as built drawing incorporation of revision prior for hand over. Conduct and perform pipe testing prior for pipe and flanges integrity test such as AIR blowing, HOT OIL flushing, and Nitrogen Purging. Assist hydro and pneumatic test, hot bolting, and pre commissioning and commissioning works.

Eei Villanueva Misamis Oriental Mindanao Philippines

- Material receiving inspection of pipes, fittings,gaskets,valves,flanges,bolts and nuts, in compliance to the material list, mill certificates, test reports and correct material specification-Open box inspection for all vendor supplied and owner supplied materials and equipments-Coordinate,conduct and witness all structural site inspections such us elevation check,alignment of steel structures,plumbness and levelness,pre-tensioning of bolts,final bolt torquing,surface preparation prior for grouting and compressive test of cube samples.-Coordinate,conduct and witness all piping site inspections such as fit up inspection of pipe spools,visual inspection of welding and line checking-Coordinate, conduct and witness all fabrication shop inspection of fit up inspection, dimensional inspection and visual inspection of welding confirming to approve construction drawings-Witness Non Destructive Testing such as PT and UT. Ensures that all welds meets the project requirements and in accordance to the WPS

Barangay Binugao, Sta Cruz Davao Del Sur

-Review of equipment drawing, piping ISO drawing and specification for painting -Check material properties based on operating temperature range and appropriate standards indicated in drawings and specifications.-Checks material condition prior to installation based on standard procedures.-Recommends corrective disposition on non-conformance report.-Conduct inspection by checking the paint material to be used based on operating temperature range, surface preparation, material identification, condition of RH, dry thickness after each application of paint and appearance of painting film.-Responsible for final inspection together with client and owner representative prior for final acceptance.-Maintain quality inspection documents/record as approved project requirements and project specification.-Monitoring the status of on painting activities such as piping and mechanical equipment.-Performs other duties as may assigned from time to time.

Barangay Simlong Batangas City

-Conduct Fit-Up Inspection and Visual Inspection during/after welding. -Line checking of pipes actual design, position, nature of welding and installation including revision.-Make quality control inspection report for QC documentation and issue suitable documents according to non-conformance procedures.-Visual inspection, checking and evaluating of final welding job, i.e. appearance, under cut, irregular cracks, pin hole, arc strike and other insufficient welding reinforcement as per ASME Standard.-Witnessed Hydro-Test and Pneumatic Test prior for restoration-Conduct monitoring of Test Packages prior for testing, i.e. Hydro Test; Pneumatic Test (Documentation)-Material receiving Inspection and Documentation-Develops and Implements method of quality control procedure-Inspection in place and deliver materials on site for conformance with the requirement of the contract.-Conduct final inspection together with client and owner representative prior for final acceptance and turn over.-Conduct inspection for rotating and static equipment.-For rotating equipment, we conduct inspection by checking the centering, elevation, levelness, and alignment of motor to pump, coupling gap, and pipe stress. Be sure that all must be comply for the required tolerance.-For static equipment, horizontal or vertical equipment, we conduct inspection by checking the plumpness, elevation, levelness and orientation of equipment.-Inspection of equipment preservation and prevention of all rotating and static equipment at site and ensure the integrity of the equipment prior to turn over period.-Conduct serration inspection prior to bolt tightening -Conduct inspection of bolt tightening with require torque value.

Bachelor Of Science In Mechanical Engineering, Mechanical Engineering

Mechanical Engineering, Bachelor Of Science In Mechanical Engineering

Activities and Societies: Philippine Society of Mechanical Engineers June 2007 -- April 2015