Served as a Responsible Engineer, (R.E.), for ASME Pressure Vessels, API 650 Tanks and unloading railcar/truck arms. Senior mechanical designer and modeler for pressure vessels, pumps, tanks and other mechanical equipment. Submitted Scope of Work for packages, attend kick off meetings and review/approve vendor documentation. Coordinated with other disciplines to maintain project schedule. Updated S3D and AutoCad Plant 3D models. Served as the Factory Acceptance Testing (FAT) and Carry Over Work coordinator. Key Achievements: Completed PE200: Lead Engineer Training

Served as a Responsible Engineer, (R.E.), specializing in Amine towers and knock out drums. Executed a million-dollar order while maintaining commitments to the budget and schedule. Attended kick off meetings as required. Perform Compress calculations on towers and drums. Resolved problems with minimal cost and schedule impacts. Worked with Project procurement and the vendor to ensure milestones were met. Initiated and completed Change Notices. Reviewed data sheets ensuring that they are in compliance with ASME BPVC, Section VIII, Div 1 Code. Coordinated with multiple in-house engineering disciplines, providing clear, concise information, documentation and solutions ensuring that the deliverables were produced and shipped on schedule. Model Pressure Vessels, Tanks, Pumps and Heat Exchangers in S-3D.

Led a work share team of junior engineers in all activities of the FEED design activities as needed. Defined work procedures and work process' between the Houston office and the New Delhi office. Conducted Code calculations as required. Reviewed vendor drawings for compliance with project specification, standards, and Code requirements. Managed the work process, coordinated work with the New Delhi office.Key Achievements: Mechanical Department Recognition in providing dedicated support to the Fluor India Office.

Designed and modeled structural pipe supports, stairways, platforms & handrails using S-3D. Updated S-3D mechanical models to include pumps, tanks, pressure vessels, conveyors, and hoppers.

Prepared and reviewed datasheets and performed design calculations for pressure vessel. Coordinated directly with the client in the Philippines. Defined cost saving work procedures and work process' between the Houston office and the Philippines office. Responsible for designing, modeling, and checking pressure vessels and corresponding ladders and platforms drawings as well as API tanks. Reviewed vendor drawings and data sheets ensuring that they are in compliance with client requirements, industry codes and standards.Key Achievements:Introduced a cost savings measure which saved them over $100,000.00. Commended by project lead for close coordination and distributed execution of standards and work processes with our satellite office. Identified approximately 5% in potential man-hour savings by optimizing resources and streamlining the work process. Developed standards for consistent and quality deliverable. Mentored less experienced designers, while instilling motivation and teamwork

Coordinated with manufacturing throughout the product life cycle ensuring a quality deliverable. Entered and maintained part numbers and Bills of Materials. Train new designers. Created MS Excel spreadsheets to design manway davits and determine nozzle projections. Perform Code calculations and produce vessel fabrication engineered drawings.

Wrote inspection and calibration procedures for incoming inventory. Wrote and implemented procedures for inventory control. Identified the root cause and developed a corrective action on design flaws of deliverables. Assisted manufacturing in the design of various jigs and fixtures to produce a consistent product. Designing and detailed structural steel skids and linear lift oil units using AutoCAD and Solidworks

Created pressure vessel drawings, and reviewed vendor documentation.

Designed pressure vessels (i.e. contact towers, gas scrubbers, regen units) for on-shore skids using AutoCAD. Trained personnel in CAD Works 3-d program.

P&ID's and facility 3-D modeling using CAD Works.

Managed design team for 4 different manufacturing facilities. Processed corrective actions and calculated the price of non-conformance. Wrote design qualification testing procedures for UN non-bulk packages. Wrote and updated Transport Canada quality control manuals for their DOT/TC plants. Product Development - Designed the 200# “mini” propane tank. Provided technical support to customers and sales staff. Managed customers’ orders from the quote stage through production. Entered Bill of Operations (BOO) and Bills of Material (BOMs) in ManFact ERP data base. Responsible for designing, performing calculations and approving ASME BPVC Sec. VIII, Div.1 pressure vessel designs and where applicable ensured that they complied with NFPA58 & RVIA. Designed DOT / TC cylinders as well as both bulk and non-bulk packages. Key Achievements:Completed Dale Carnegie Casting Leadership Excellence training. Completed training class in Total Quality Management (TQM) and Enterprise Resource Planning (ERP).