• Responsible for maintenance of electrical equipment at GDC Zone 3 consist of GDC Plant 3, GDC Plant 4, GDC PICC and GDC Wisma Putra• Acted as team leader for electrical team and managed technicians at GDC Zone 3.• Accountable for the preventive and corrective maintenance works of power transformer, switchgear, electrical motor, diesel generator, Variable Frequency Drive ,fire protection system and AC/DC UPS.• Responsible in creating maintenance and service contracts for electrical… Show more • Responsible for maintenance of electrical equipment at GDC Zone 3 consist of GDC Plant 3, GDC Plant 4, GDC PICC and GDC Wisma Putra• Acted as team leader for electrical team and managed technicians at GDC Zone 3.• Accountable for the preventive and corrective maintenance works of power transformer, switchgear, electrical motor, diesel generator, Variable Frequency Drive ,fire protection system and AC/DC UPS.• Responsible in creating maintenance and service contracts for electrical department.• Accountable for revising quotation, raising purchase requisition using SMARTGEP and applying CAPEX and OPEX from Board of Committee. • Managed and oversaw any work involving vendor during planned task such as calibration and services.• Involved in design for special project requested by Operation Team for plant optimization Show less

• Involve planning and coordination with contractor for 33kV SSU construction , 33kV Consumer SSU, 33kV PM3 GIS Room, 6.6kV E-House Installation, 33kV power cable and 6.6kV power cable installation from Consumer SSU to PM3 GIS Room and Cogen Plant. •Responsible for monitoring during Testing and Commissioning of 33KV Power system such as HV cable Hipot Test, Relay Calibration, GIS Switchgear power testing, and SF6 Quality Gas Check.•Act as key people for coordination during GTG load… Show more • Involve planning and coordination with contractor for 33kV SSU construction , 33kV Consumer SSU, 33kV PM3 GIS Room, 6.6kV E-House Installation, 33kV power cable and 6.6kV power cable installation from Consumer SSU to PM3 GIS Room and Cogen Plant. •Responsible for monitoring during Testing and Commissioning of 33KV Power system such as HV cable Hipot Test, Relay Calibration, GIS Switchgear power testing, and SF6 Quality Gas Check.•Act as key people for coordination during GTG load test by responsible for 18MW load bank installation for PM3 Transformers key person for communication during testing.• Liaised closely with consultant and contractor during TNB Piat, Bomba Inspection and authority such as Indah Water and MPKL for building Certificate of Completion and Compliance CCC.•Responsible for maintenance of electrical equipment at Waste Water Treatment Plant (WWTP), Waste to Energy Plant (WTE) and COGEN plant•Act as team leader for electrical team and managed technician for normal and shift • Involved in preventive and corrective maintenance of power transformer, switchgear, electrical motor, submersible pump, diesel generator, variable frequency drive, AC/DC UPS, compressor and special machine such as belt press.• Key Person of SAP system for any work order assigned by maintenance & operation team.• Accountable for revising quotation, raising purchase requisition and applying CAPEX for maintenance team.• Managed and oversaw any work involving vendor during planned task such as calibration and services.• Involved in design for special project requested by Operation Team Show less

•Involved in carrying out maintenance for electrical for 80MW x 2 Power Plant. In addition to that, I also managed preventive maintenance and predictive maintenance for electrical equipment such as Power Transformer, Induction motor, AC/DC UPS and Switchgear. •Experience in designing low voltage panel such as motor starter panel used for testing small load such as DOL Motor. Do calculation on the motor characteristic such as power and amp to determine the cable size, contactor and the… Show more •Involved in carrying out maintenance for electrical for 80MW x 2 Power Plant. In addition to that, I also managed preventive maintenance and predictive maintenance for electrical equipment such as Power Transformer, Induction motor, AC/DC UPS and Switchgear. •Experience in designing low voltage panel such as motor starter panel used for testing small load such as DOL Motor. Do calculation on the motor characteristic such as power and amp to determine the cable size, contactor and the thermal overload protection of the motor. • Assisted HOD to review the equipment monthly checklist and highlight any abnormal result.• Responsible for supervising technician for any related task involved inside the plant such as planned task or any breakdown task. Moreover, I also assisted technician at site for troubleshooting work. Show less

Involved in Motor Control Circuit (MCC) Maintenance, Transformer 11kv Maintenance, Diesel Generator, 415V and 3.3kV Induction Motor Maintenance and Installation, Team member for new 2000kVA Transformer Installation. Testing Relay such as Thermal Overload and also Under Voltage Control Relay (UVCR). Involved with HSE Department for fire fighting drill in plant substation.

Involved in 415V Low Voltage Overhead Line, 11kV Substation Maintenance , 11kV Underground Cable , Project Department and also Metering Installation.