• Designing, commissioning and Installation of Air Quality Monitoring equipments and meteorological sensor • Service, maintenance & calibration of Horiba, Thermo, Recordum, Trunkey, Aeroqual analyzer• Configuration of wireless modem for data communication.• Troubleshooting of electrical distribution panel, UPS/inverter, AC & DC motors, designing the power system for machinery with solar panel and good knowledge to understand the electrical and P&ID.• Prepared service and monitoring reports• Online technical support and training to our existing client.• Prepared the technical and commercial proposal as client requirement.

▪ Testing and commissioning of new equipment (Horiba PG 250, PG250, Gas cooler, dust monitor, stack monitoring equipment)▪ Repair and maintenance of emission and ambient air quality analyser and testing of new analyzer.▪ Prepared testing and calibration report.▪ Online support to local and international customers

I was handling a project of Saudi Aramco for installation & maintenance in the production plant. The responsibilities are as follows.▪ Diagnosed and troubleshooting broken devices, electrical system and electronic equipment on daily basis.▪ Maintained organized archive of drawings and other electrical design documents.▪ Installed electrical circuits, wires, and other electrical equipment▪ Performed calibration of Pressure transmitter, Pressure gauge, temperature sensor▪ Diagnose problems by interpreting and working from engineering drawings, blueprints, schematics and equipment manufacturer’s literature▪ Excellent analytical and troubleshooting skills typically required for the maintenance of compressor control systems, AC & DC electrical motor, automated valves, and computer networks▪ Responsible for operation and maintenance plant electrical distribution systems (MV Switchgear, LV distribution, Emergency Diesel Generators, Power Monitoring system, MCC & VSD, Lighting, UPS etc.)▪ Troubleshooting, operation, maintenance, calibration and repair of various types of electronic, electric, pneumatic, hydraulic equipment, air quality monitoring and lab equipment ▪ Plans layouts, runs conduit, wiring and tubing in both new and existing installations▪ Conducted feedback and report on the condition of system/equipment and presented finding to managers

▪ Design & Maintenance and calibration all Analytical Equipment’s control logic and▪ Loop Schematics for equipment and field instruments.▪ Commissioning Trouble shooting & Calibration of AQM HORIBA, Teledyne, Signal, Aeroqual AQM- 60, Met one, Sabio Analyzer and Meteorological Sensor.▪ Installation Calibration and maintenance of Laboratory equipment: (HPLC, GC, Atomic Absorption Spectrometer, X-Ray photoelectron Spectroscopy, Molecular Beam Epitaxy, XRF, XRD, Fermentation & bio reactor, Autoclave, Microscope, UV Chamber, Environmental Chamber, Microwave Digestion System, Incubator, Furnace, pH Meter, Balance, Biological Safety Cabinet, Hot Plate, Centrifuge, commissioning with the control software.▪ Attending instruments breakdown calls .Hardware repair, Trouble shooting and calibration of Instruments. Running QC samples.▪ Fault trouble shooting of electrical panel, Controlling, PLC base machinery, Pneumatic and hydraulic system, AC & DC motor, transformer, compressor, switch gear, All type of sensor and proximity switch, able to read electrical and electronic circuit diagrams, electrical wiring etc.▪ Installation and Commissioning of CNC Water jet, Rolling Mills, Hydraulic press, Monitor Impact Tester, Lath Machine▪ Read blueprints, diagrams and schematic drawings to determine work procedures▪ Install, align, take apart and move stationary industrial machinery and mechanical equipment, such as pumps, fans, tanks, conveyors, furnaces and generators according to layout plans using hand and power tools▪ Operate hoisting and lifting devices, such as Trolley, jacks and fork lift, to position machinery and parts during the installation, set-up and repair of machinery▪ Inspect and examine machinery and equipment to detect and find irregularities and malfunctions▪ Knowledge of hydraulic and pneumatic systems, and programmable logic controls▪ Adjust machinery and repair or replace defective parts

▪ Fault trouble shooting of PLC base Spinning, Ring, Drawing and carding machinery, pneumatic system, PLC & Inverter, Module, Ac & Dc drives, HMI, SCADA system, Sensors, Switch gears, Temperature controller, Temperature & Pressure Sensor, Heater, power transformer, starter, Power supplies, CT, protection system of machineries, Service & maintenance.▪ Working experience on SCADA system, HMI and PLC Programming.▪ Able to read electrical and electronic circuit diagrams.

▪ Installation and erection of PLC base Toyota Air jet Loom.▪ Fault trouble shooting of programmable machinery, Cargo lift, overhead cleaner beam trolley, Service & Maintenance of machinery.▪ Testing of 3ph, single phase AC & DC Motor, Switch Gears, Transformer, Compressor, power distribution controlling panel, protection relays.▪ Preparation of Grounding/Earthling.▪ Installation of Cable tray and HV Cabling testing and commissioning.▪ Taking care of all Controlling panel, Electrical panel and LT room.