Puneet Agarwal, Ph.D. Email & Phone Number

San Luis Obispo, California, United States

Southlake, Texas, United States

Buffalo, New York, United States

Buffalo/Niagara, New York Area

Spread of Rumors, Misinformation, and Disinformation on Social Media during Disasters (NSF-Funded Project)

Atlanta, Georgia, United States

Provided enhancements to the Consumer Converting Network Model (CCNM) by (a) improving the solution quality of the optimization model and (b) integrating a mapping functionality into the user interface for CCNM. Reduction in Problem Size: 94% (approx.)Improvement in Solution Quality: 93% (approx.)

Buffalo/Niagara, New York Area

Teaching Assistant for Course - IE 576 Applied Stochastic Processes

Buffalo/Niagara, New York Area

Teaching Assistant for Course - IE 412/512 Decision Analysis

Buffalo/Niagara, New York Area

Manage and record financial transactions and expenditure in the club

Buffalo/Niagara, New York Area

Development of a VBA tool for warehouse utilization calculation

Atlanta, Georgia

Developed a fully automated route estimating system (ARES) for merchandising display unitAttributes used: Display and machine processing requirements and die-line images of the displaysPrediction Performance: Achieved an overall F1 score of 91%Estimated Cost Savings: $4 Million USDEstimated Time Reduction: Approximately 60% of the initial time

Buffalo/Niagara, New York Area

TA for course "Engineering Economy"

Buffalo/Niagara, New York Area

TA for course " Planning Production and Service Enterprise".

Jharsuguda Area, India

Kolkata Area, India

a) Scratching and Nano indentation of Soda-Lime-Silica (SLS) glass i) Explore the surface deformation mechanisms of SLS glass ii) Scratching of glass under normal loads of 2, 5, 10 and 15 N ii) Scratching speeds of 0.1, 0.2, 0.5 and 1.0 mm/s iv) Rockwell C diamond indenter with ~200 μm tip radiusb) Nano indentation of SS316L Alloy Steel i) Plasma nitriding of 5 mm thick slices of AISI 316L austenitic stainless steel ii) Assessment of hardness of nitrided… Show more a) Scratching and Nano indentation of Soda-Lime-Silica (SLS) glass i) Explore the surface deformation mechanisms of SLS glass ii) Scratching of glass under normal loads of 2, 5, 10 and 15 N ii) Scratching speeds of 0.1, 0.2, 0.5 and 1.0 mm/s iv) Rockwell C diamond indenter with ~200 μm tip radiusb) Nano indentation of SS316L Alloy Steel i) Plasma nitriding of 5 mm thick slices of AISI 316L austenitic stainless steel ii) Assessment of hardness of nitrided layer using a nano indentation method on a Fischer scope using different test loads.c) Nano indentation of Ti-6Al-4V i) Nano scale mechanical properties of plasma nitrided TA samples are investigated ii) Experiment is carried out by using nano indentation with a Berkovich indenter of ~150 nm ti radius.d) Nano indentation of Sapphire i) Determination of nano scale mechanical properties of sapphire sample ii) Experiment is conducted with a commercial nano indenter (TriboIndenter Ubi 700, Hysitron Inc., Minneapolis, MN) Show less

Bokaro Area, India

Advisor: Mr. Vivekanand Rai, Chief Engineer, Workover ServicesProject: Problems and remedial measures in workovera) Investigation of operational problems with sucker rod pumpsb) Troubleshooting sucker rod pumpsc) Troubleshooting progressive cavity pumpsd) Troubleshooting electric submersible pumpse) Planning for pump repairsf) Detecting tubing leaksg) Maintaining the compressor engineh) Removing and preventing scalei) Solving gas production problemsj)… Show more Advisor: Mr. Vivekanand Rai, Chief Engineer, Workover ServicesProject: Problems and remedial measures in workovera) Investigation of operational problems with sucker rod pumpsb) Troubleshooting sucker rod pumpsc) Troubleshooting progressive cavity pumpsd) Troubleshooting electric submersible pumpse) Planning for pump repairsf) Detecting tubing leaksg) Maintaining the compressor engineh) Removing and preventing scalei) Solving gas production problemsj) Treating and disposing produced water Show less

Vishakhapatnam Area, India

Advisor: Mr. C.S. Bhagat, Senior Manager, Maintenance DepartmentProject: An investigative study on hydraulic systems in Medium Merchant and Structural Mill (MMSM) in Vizag Steel Planta) Hydraulic system of walking beam reheating furnace i) Specifications of existing hydraulic system ii) Working of existing hydraulic system iii) Safety and error faults iv) Role of PLC in hydraulics v) Merits and demerits of existing hydraulic systemb) Hydraulic system of… Show more Advisor: Mr. C.S. Bhagat, Senior Manager, Maintenance DepartmentProject: An investigative study on hydraulic systems in Medium Merchant and Structural Mill (MMSM) in Vizag Steel Planta) Hydraulic system of walking beam reheating furnace i) Specifications of existing hydraulic system ii) Working of existing hydraulic system iii) Safety and error faults iv) Role of PLC in hydraulics v) Merits and demerits of existing hydraulic systemb) Hydraulic system of finishing area i) Components of existing hydraulic system ii) Working of existing hydraulic system iii) Troubleshooting hydraulic system iv) Merits and demerits of existing hydraulic system v) Modifications in hydraulic system Show less

Doctor Of Philosophy - Phd, Operations Research

Master'S Degree, Operations Research

Bachelor'S Of Engineering, Production And Industrial Engineering