Ram Kumar Email & Phone Number

Kuala Lumpur, My

Selangor, Malaysia

Real Time Dynamic Simulation Experience:• Provide continuous technical support/troubleshoot for MSi proprietary pipeline simulation software (leak detection system, Virtual metering system, virtual pipeline management) installed within SEA region.• Collecting historical data from site and re-simulate scenarios to troubleshoot on any unmatched data between measured and predicted result.• Provide offline simulation report to client on monthly basis by use real time data, report summary includes predicted Vs measured error (Pressure, flow, temperature), mass imbalance within the line, frozen/bad input data from OPC/PI server, pig arrival estimate time, recommendation to client to rectify/confirm error related issues.• Running the pigging planner utility to check on various parameters like estimated pig arrival time, pig velocities and slug catcher levels.• Provide budgetary proposal/Cost-Time request (CTR) for expansion job, maintenance renewal contract, modification and system upgrade quotation. • Providing post installation technical support and customer training for installed simulation software.Flow Assurance Experience:• Provide technical service support for flow assurance issues, in particular steady state and transient multiphase flow modeling for operations such as start-up, cool down, depressurization, etc. • Perform surge analysis studies using OLGA and PIPENET.• Line sizing for rigid and flexible flowlines and risers.• Assessing insulation requirements for buried and not buried flowlines.• Modeling steady state and transient operating cases in PIPENET and OLGA.• Accessing mini & max operating envelopes for various different operating & production cases.• Carrying out transient studies looking at turn down, shut-in, depressurization, restart and ramp up cases.• Analysis of flow regime.• Fluid characterization using PVTSim and GUTS.• Hydrate management philosophies at normal and turn down operations.

Selangor, Malaysia

Experience & Responsibilities: •Liaison and point of contact between Client, Vendors, Fabricators and internal departments (Process, Structure, Drawing Office, QA/QC, Procurement and Shipping).•Dealing with contractual Purchase Orders and Variation Orders with Client. Also driving the project commercial policy and control of individual project budgets.•Receipt of technical and commercial specification affecting design, technical aspects of inspection, quality control, fabrication and delivery.•Prepare technical content of purchase order requisitions for raw material, equipment and fabrication.•Review and approval of Vendor bids with respect to purchase order requirements to meet project specification.•Generate and establish overall project schedule together with Vendor schedule. This is updated on monthly basis.•Furnace General Arrangement, Data Sheets, Quality ITP, Overall Project Schedule and Document Index.•Fabrication detail drawings to designated fabricators in correlation with raw material purchased.•Prepare monthly project status report to Client and Upper Management that comprise of commercial and technical content of individual projects. Internal reports illustrate all information required for payment milestone for invoicing, procurement status, schedule and documentation.•High knowledge of Furnace and its auxiliary equipment; Burners, Air Pre-heater, Industrial Fans, Soot-blowers and Instruments.•Knowledge of Furnace P&ID inclusive of; Burners, Sootblowers, Fans, Air Pre-heater and instruments. Design of Fuel Skid and Burner Management System for client overall Distributed Control System.•Attended kick off meeting with international clients and pre-inspection meeting with domestic fabricators.

Selangor, Malaysia

Experience & Responsibilities: •Provide assistance to the Lead Instrument Engineer in the daily coordination & management of the Instrument design team in the Project Task Force.•Developed loop diagrams, wiring diagrams, junction boxes, local panel layout, instrument index, data sheets, cable block diagram & cable schedule. Generated cable lists. Reviewed & checked instrument's location plan & cables routing.•Prepared logics narratives & generated alarm summaries. Generated I/O list for DCS/PLC.•Interfaced with DCS/PLC & MCC for power requirements & motor controls.•Interfaced with piping, mechanical, electrical & project groups for all instrumentation issues.•Evaluated packaged equipment vendor's quotations reviewed & checked deliverable instruments documentation. Participated in packaged skids checkout & acceptance.•Monitor contractors/vendors scope of work.•Monitor & responsible to authorize the DCS, SCADA/PLC system FAT.

Selangor, Malaysia

Jan 2007 ~ Jan 2008 PENFIBRE (Malaysia) (Migration MICRO XL to CENTUM CS3000)• System programming, graphic Generation. • Perform S.A.T &F.A.T Mar 2008 ~ June 2008 JJ Lurgi Engineering – PT. Pelita Agung Agrindustri (Indonesia) (Biodiesel & Glycerin Plant)• Site Commissioning• Troubleshooting (from DCS & field) instruments such as control valves, low, pressure, temperature transmitters, level switches.July 2008 – Dec 2008 PETRONAS (Mega Methanol Labuan) • Centum CS3000 System, Software and graphic generation.• Create Modbus taglist and perform communication link verification with Honeywell PLC• Perform F.A.T

B.Eng (Hons) Electronics Engineering, (Control System), 2Nd Class

Higher Diploma, Engineering (Electrical/Electronic), 2Nd Class

Certificate, Electronics Engineering, Control System, 2.54Cgpa