• Undertake teaching and teaching-related duties such as design, preparation, and development of teaching materials; conduct classes, tests, and practicals; marking and assessment;• Plan and implement teaching strategies for subjects Physics, Additional Mathematics, Mathematics, Bahasa Inggeris, and Bahasa Malaysia to optimize student learning as well as to motivate them;• Establish and maintain high standards of teaching and effective learning to meet the school’s teaching and learning… Show more • Undertake teaching and teaching-related duties such as design, preparation, and development of teaching materials; conduct classes, tests, and practicals; marking and assessment;• Plan and implement teaching strategies for subjects Physics, Additional Mathematics, Mathematics, Bahasa Inggeris, and Bahasa Malaysia to optimize student learning as well as to motivate them;• Establish and maintain high standards of teaching and effective learning to meet the school’s teaching and learning expectations;• Conducting classroom assessment (PBD) and completing the PBD record set by the school administrator;• Participate in continuous relevant co-curricular activities as set by the school. Show less

Course taught:1. Additional Mathematics2. MathematicsJob scope:• Apply appropriate learning, teaching, and assessment to help students understand the subjects easily;• Establish and maintain effective teaching and learning methods using different teaching styles depending on the subjects;• Deliver lessons clearly by preparing tutorials, assignments, and materials;• Distribute and discuss the learning material during the class and monitor students’ progress.

Project Title: Structural failure of the stent due to severe hemodynamic endothelial cells at ductus arteries.Job Scope:Responsible for designing and constructing the geometry, including product details, guidelines, information regarding materials, specific measurements, and procedures for stent strut, glove, and nozzle using SOLIDWORKS;• Responsible for regulating the boundary condition and parameter assumptions for the simulation purpose;• In charge of conducting a… Show more Project Title: Structural failure of the stent due to severe hemodynamic endothelial cells at ductus arteries.Job Scope:Responsible for designing and constructing the geometry, including product details, guidelines, information regarding materials, specific measurements, and procedures for stent strut, glove, and nozzle using SOLIDWORKS;• Responsible for regulating the boundary condition and parameter assumptions for the simulation purpose;• In charge of conducting a simulation for the designs (stent strut, glove, and nozzle) using ANSYS Fluent software;• Assisting the research student in conducting the experiments for the kitchen hood recirculation system at UTM Skudai;• Responsible for evaluating and analyzing the result based on the flow characteristics and performances.• Writing the report and publishing papers in Scopus-indexed journals;• Prepared and wrote the documentation report for the projects. Show less

Project Titles:1. Meter Dose Inhaler for adult and children respiratory care.2. An invention of UTHM pipe leaking measurement for a better pipe water quality: adaption tomography and computational fluid dynamic approach to estimate the flow characteristic in UTHM pipe leaking).3. Reduction of noise emission on dry ice blasting by optimizing nozzle geometry for control health, safety, and environment.4. Thrombosis deposition near stent strut configuration in Femoropopliteal… Show more Project Titles:1. Meter Dose Inhaler for adult and children respiratory care.2. An invention of UTHM pipe leaking measurement for a better pipe water quality: adaption tomography and computational fluid dynamic approach to estimate the flow characteristic in UTHM pipe leaking).3. Reduction of noise emission on dry ice blasting by optimizing nozzle geometry for control health, safety, and environment.4. Thrombosis deposition near stent strut configuration in Femoropopliteal Arterial Morphologies.Job scope:Responsible for designing and constructing the geometry, including product details, guidelines, information regarding materials, specific measurements, and procedures for metered dose inhalers, piping, dry ice blasting, and stent strut using SOLIDWORKS;• Responsible for ensuring the mechanical design meets the product requirements and project scopes;• In charge of determining the boundary condition and parameter assumptions for the simulation;• Providing advice and technical guidance to degree students on learning best practices and helping with learning problems for projects in UTHM;• Assisting the research students in conducting mechanical engineering tests, characterizations, and reliability tests according to prototype requirements;• Evaluating and analyzing results based on the flow characteristics and performances of prototypes;• Writing the report and publishing papers in ISI and Scopus-indexed journals;• Prepared and wrote the documentation report for the projects. Show less

Project Titles:1. Structural failure of the stent due to severe hemodynamic endothelial cells at ductus arteries.2. Optimizing the composition and concentration of epoxidized natural rubber for bio-degradable glove and Microcrystalline Cellulose-NanoZnO (MCCZnO) Hybrid to reduce bubbles formation.3. Emission filtration characteristic by cold-mist spray process from kitchen hood recirculation system.Job scope:• Responsible for designing and constructing the geometry… Show more Project Titles:1. Structural failure of the stent due to severe hemodynamic endothelial cells at ductus arteries.2. Optimizing the composition and concentration of epoxidized natural rubber for bio-degradable glove and Microcrystalline Cellulose-NanoZnO (MCCZnO) Hybrid to reduce bubbles formation.3. Emission filtration characteristic by cold-mist spray process from kitchen hood recirculation system.Job scope:• Responsible for designing and constructing the geometry, including product details, guidelines, information regarding materials, specific measurements, and procedures for stent strut, glove, and nozzle using SOLIDWORKS;• Responsible for regulating the boundary condition and parameter assumptions for the simulation purpose;• In charge of conducting a simulation for the designs (stent strut, glove, and nozzle) using ANSYS Fluent software;• Assisting the research student in conducting the experiments for the kitchen hood recirculation system at UTM Skudai;• Responsible for evaluating and analyzing the result based on the flow characteristics and performances.• Writing the report and publishing papers in Scopus-indexed journals;• Prepared and wrote the documentation report for the projects. Show less

Coarse taught:1. BDA 37201 (Makmal Kejuruteraan V) 2. BDA 37301 (Makmal Kejuruteraan VI)Job scope:• Assisting the technician in preparing the laboratory materials;• Set up and prepare the laboratory for experiments and organize the equipment and supplies;• Teach students to use laboratory equipment, tools, and machines properly;• Providing the teaching materials, such as laboratory reports for the students;• Keeping records in log books of laboratory safety… Show more Coarse taught:1. BDA 37201 (Makmal Kejuruteraan V) 2. BDA 37301 (Makmal Kejuruteraan VI)Job scope:• Assisting the technician in preparing the laboratory materials;• Set up and prepare the laboratory for experiments and organize the equipment and supplies;• Teach students to use laboratory equipment, tools, and machines properly;• Providing the teaching materials, such as laboratory reports for the students;• Keeping records in log books of laboratory safety and labour protection instructions;• Responsible as an instructor in conducting research and demonstrating to the students;• Responsible for collecting and marking the student’s laboratory reports. Show less

Help the supervisor to teach the ANSYS CFD simulation in class, collected journal and editing journal in International Journal of Integrated Engineering (IJIE).

Job Scope:(Die Maintenance Service)• Responsible for cleaning the moulding die using chemical cleaning by manual scrub to remove fouling and mineral buildup;• Assist the engineer in hot-spotting the moulding die defect;• Responsible for servicing the moulding die when it reached the date;• Helping the engineer to install the new moulding die in the machine.