-Transition process towards Xeno-Aero takeover-Direct interaction and processes with the A.F.A.C (Mexico's Civil Aviation Authority)-Manual and Procedures development for F.A.A. (Federal Aviation Administration) for CFR Title 14, 145 Certification in full compliance with CFR 145 and AS9110-Internal diagnostics audits with corrective actions for compliance to AFAC, CFR 145 and AS9110-New Business Development

First Articles per AS9102 and Source Inspection of Wire Harness

Instructor for next assignments-Technical English for A&P Mechanics-Aerodynamics for Commercial Pilots-Aircraft Electric Systems for A&P Mechanics

Final Assembly Line Supervisor for A5 model -Assembly Process Transfer from Vacaville CA to Tijuana Mexico-Implement and track KPI's for Final Assembly Line-Reduction of 75% of defects to the customer in 7 months-Increase production in 80% in 7 months

• Systems and Structures Quality Agent at customer facilities – Bombardier Aerospace at Queretaro Mexico.• Physical inspection of structures assemblies including aerodynamic requirements, sealing, corrosion protection and inspection of standard and specialized fasteners such as Hi-Lites and Hi-Locks per Bombardier Aerospace Standard Practices (BAPS).• Physical inspectin of different systems installation and assembly such as hydraulic lines, fuel lines, tubing swage, electrical harnesses… Show more • Systems and Structures Quality Agent at customer facilities – Bombardier Aerospace at Queretaro Mexico.• Physical inspection of structures assemblies including aerodynamic requirements, sealing, corrosion protection and inspection of standard and specialized fasteners such as Hi-Lites and Hi-Locks per Bombardier Aerospace Standard Practices (BAPS).• Physical inspectin of different systems installation and assembly such as hydraulic lines, fuel lines, tubing swage, electrical harnesses and hardware torquing requirements per Bombardier Aerospace Standard Practices (BAPS). Show less

Project Specialist as On-site Quality Representative for Airbus/Bombardier on A220 program at supplier facilities – Safran Aerospace at Tijuana Mexico.• Source Inspection on interior cabin and cargo parts for cosmetics, documentation and dimensions using different metrology instruments such as high gage, caliper, micrometer, pins, radius gage, etc.• Focal point as lead source inspector for a total crew of 9 and on site back up for customer SQE• Statistical data and reports… Show more Project Specialist as On-site Quality Representative for Airbus/Bombardier on A220 program at supplier facilities – Safran Aerospace at Tijuana Mexico.• Source Inspection on interior cabin and cargo parts for cosmetics, documentation and dimensions using different metrology instruments such as high gage, caliper, micrometer, pins, radius gage, etc.• Focal point as lead source inspector for a total crew of 9 and on site back up for customer SQE• Statistical data and reports generation at source inspection station for further analysis with stakeholders• First Article Inspection Reports revision, validation and acceptance as customer representative per AS9102 Rev. B.• Training supplier First Article dedicated crew per AS9102, providing initial training, on the job training and full support as customer representative to clarify any discrepancy or doubt with full customer authority.• Quality Improvement Plan proposal and follow-up• Kaizen event participation as customer representative. Show less

• Review, modify, update, and assess the Quality Management System to AS9100 Rev. D compliance including the Quality Manual and all Quality System Technical Documents Level 1, 2 and 3.• Create AS9100 Rev. D compliance plan based on previous assessment with specific tasks and responsible• Enforce proper parts and components traceability per Aerospace industry requirements• Outline and upgrade FOD control program in order to be following NAS412 and OASIS SCHM section 3.4.2• IAQG… Show more • Review, modify, update, and assess the Quality Management System to AS9100 Rev. D compliance including the Quality Manual and all Quality System Technical Documents Level 1, 2 and 3.• Create AS9100 Rev. D compliance plan based on previous assessment with specific tasks and responsible• Enforce proper parts and components traceability per Aerospace industry requirements• Outline and upgrade FOD control program in order to be following NAS412 and OASIS SCHM section 3.4.2• IAQG OASIS Administrator• Initiate supplier surveillance program together with materials department by implementing measurable KPI’s and follow up with assessments and on-site audits. Risk Analysis and Mitigation and direct interaction with suppliers. Also implementing new program to assure proper flow down of customer and regulatory requirements to vendors thru Tur-Bo Jet products own Quality Clauses that match regulatory and customers’ requirements. Show less

Project Specialist for Fokker Aero-Structures with vendor Tecmaq machine shop in Monterrey Mexico.• Source Inspector on different machined parts for compliance with customer and regulatory requirements including paperwork and dimensioning per GD&T ANSI Y14.5 using different metrology instruments such as high gage with dial indicator, caliper, micrometer, pins, radius gage, etc.• Lead Quality Improvement Plan development and implementation• Guide on final customer, government… Show more Project Specialist for Fokker Aero-Structures with vendor Tecmaq machine shop in Monterrey Mexico.• Source Inspector on different machined parts for compliance with customer and regulatory requirements including paperwork and dimensioning per GD&T ANSI Y14.5 using different metrology instruments such as high gage with dial indicator, caliper, micrometer, pins, radius gage, etc.• Lead Quality Improvement Plan development and implementation• Guide on final customer, government, military and standard industry specifications interpretation• Guidance and training on Corrective Actions investigations and as a Champion• Start review and update inspection plans for Fokker Part Numbers• Train QA personnel on proper drawings reading per GD&T standard ANSI Y14.5, including Engineering Orders and all additional documents. Show less

• Launch Alfa-Aero Quality System in order to be in compliance with AS9110• Create and maintain Quality Manual in compliance to AS9110• Create and maintain Quality System documents Level 1, 2 and 3 in compliance to AS9110.• Create second level procedures for Quality System• Train to management team on the Quality System and related documents.• Set up production plan and prepare operational technical documents for a 1C service of an Embraer ERJ-145EP such as Service Task… Show more • Launch Alfa-Aero Quality System in order to be in compliance with AS9110• Create and maintain Quality Manual in compliance to AS9110• Create and maintain Quality System documents Level 1, 2 and 3 in compliance to AS9110.• Create second level procedures for Quality System• Train to management team on the Quality System and related documents.• Set up production plan and prepare operational technical documents for a 1C service of an Embraer ERJ-145EP such as Service Task Cards and Non-Routine cards.• Follow up 1C service process during execution and production control paperwork• Analysis and Evaluation of Non-Routine cards generated during the inspection process using Embraer Technical information for support such as AMM, SRM, AIPC, ESC, etc.• Parts Order Analysis based on Embraer AIPC and SRM.• Support to Sales department as a technical advisor on customer visits and meetings.• Collaborate on the creation of the Shop Procedures Manual• D.G.A.C. (Mexican Civil Aviation Authority) Repair Station certification and approval• Engines and APU’s remove and install• Landing Gear remove and install• Flight Control Surfaces rigging, remove and install• Evaluate and quote A, B and C services on aircrafts described above.• Support Engineering with Structural Repairs on metal and composites structures / components, including beyond manual repairs designs for further DER approval.• Lead composites shop launch and set-up at initial phase with continued support during subsequent operations.• Plane crash project at Mexicali dessert for Discovery Channel with B-727-200 return to service at Mexicali Airport applying Airworthiness Directives and minor services, including removal of ventral stairs and door. Show less

• IAQG / OASIS administrator• Review, request modifications and updates and finally approve shop floor methods and operations sheets.• Lead Permanent Aircraft Parts Manufacture Certification with DGAC (Mexico’s Civil Aviation Authority) • Revise modify and update of Quality Manual in order to incorporate F.A.A. requirements for PMA’s and STC’s. • Head of Document Control Department, including review, update and final approval of all Quality System Documents Levels 1, 2 and… Show more • IAQG / OASIS administrator• Review, request modifications and updates and finally approve shop floor methods and operations sheets.• Lead Permanent Aircraft Parts Manufacture Certification with DGAC (Mexico’s Civil Aviation Authority) • Revise modify and update of Quality Manual in order to incorporate F.A.A. requirements for PMA’s and STC’s. • Head of Document Control Department, including review, update and final approval of all Quality System Documents Levels 1, 2 and 3.• Lead F.A.A. PMA / STC Production Certificate Holder Approval to incorporate new main offices in Tempe Arizona.• Certify new building / business unit under Boeing BAC 5331non-structural composites parts type I, III, IV & V. • Incorporate new composites building / business unit to actual AS9100 campus certificate. • Acting Senior Quality Manager from December 2014 to June 2015. • Lead Quality activities during Last Minute Shop start-up phase in Toulouse France to support Airbus GRAMS activities and get approved as a supplier. Also implement Quality System in compliance to AS9100 to be ready to get certified under local administration.• Lead new Mexicali site for composites manufacturing in AS9100 Rev. C certification audit. • Lead new site AS9100 Rev. C certification process in Taylorsville, North Carolina. • Lead AS9100 Rev. C re-certification audit for Main Site in Tempe AZ, Calexico CA, and 2 sites in Mexicali including new composites facility. • Head of Receiving Inspection area and responsible for monitoring supplier’s performance by tracking KPI’s. Part of this suppliers monitoring process was to integrate the Supplier Quality Engineer position to the area providing training and coaching for supplier’s evaluation, including a more detailed Corrective Actions program that includes 8D’s methodology implementation and on site audits for low performance suppliers acting as Lead Auditor. These actions lead to a tangible supplier’s performance improvement. Show less

• Lead 2 periodical certifications for Aircraft Parts Manufacture with DGAC• Head of department with 2 QA Engineers, 2 QA technicians and 7 Inspectors• Upgrade on hardware and software to make more efficient the CMM Metrology Lab, reducing the inspection times by 70% incorporating new software as Verisurf and Inspection Xpert. This reduce the First Article Inspection from 3 days/part to 4hr/part.• Participate on AS/EN/JISQ9100:2009 – Rev. C and ISO 9001:2008 Certification• Lead… Show more • Lead 2 periodical certifications for Aircraft Parts Manufacture with DGAC• Head of department with 2 QA Engineers, 2 QA technicians and 7 Inspectors• Upgrade on hardware and software to make more efficient the CMM Metrology Lab, reducing the inspection times by 70% incorporating new software as Verisurf and Inspection Xpert. This reduce the First Article Inspection from 3 days/part to 4hr/part.• Participate on AS/EN/JISQ9100:2009 – Rev. C and ISO 9001:2008 Certification• Lead and train metrology lab inspector to learn new measurement equipment such as micrometer, high gage with dial indicator, internal diameter micrometer, pins. Drawing interpretation per GD&T standard ANSI Y14.5. Also on Verisurf software for portable CMM FaroArm.• Review and request updates and modifications for production floor Methods and Operations sheets. Show less

• Initial phase of the MRO shop, including process definition and structure, also dealing with DGAC authorities and establishing initial requirements• Support to Sales department as a technical advisor on customer visits and meetings.• Collaborate on the creation of the Shop Procedures Manual• Shop certification and approval• Evaluate and quote A, B and C services on B727-200, B737-300/500 series, DC-9, MD-90 and ERJ-145/175 aircrafts based on the Maintenance Planning Data… Show more • Initial phase of the MRO shop, including process definition and structure, also dealing with DGAC authorities and establishing initial requirements• Support to Sales department as a technical advisor on customer visits and meetings.• Collaborate on the creation of the Shop Procedures Manual• Shop certification and approval• Evaluate and quote A, B and C services on B727-200, B737-300/500 series, DC-9, MD-90 and ERJ-145/175 aircrafts based on the Maintenance Planning Data (MPD) applicable Task Cards. Show less

• Initial phase of starting MRO facility for narrow and wide-body airliners.• Collaborate on the creation of the Shop Procedures Manual• Create Specialty Shops Procedures Manuals (Composites Shop, Oxygen Shop, Batteries Shop)• Work together with Quality Assurance to create Process Mapping, Quality Manual and Shop Floor procedures.• Head of department with 2 Engineers• Evaluate and quote A, B and C services on B727-200, B737-300/500 series and DC-9 aircrafts based on the… Show more • Initial phase of starting MRO facility for narrow and wide-body airliners.• Collaborate on the creation of the Shop Procedures Manual• Create Specialty Shops Procedures Manuals (Composites Shop, Oxygen Shop, Batteries Shop)• Work together with Quality Assurance to create Process Mapping, Quality Manual and Shop Floor procedures.• Head of department with 2 Engineers• Evaluate and quote A, B and C services on B727-200, B737-300/500 series and DC-9 aircrafts based on the Maintenance Planning Data (MPD) applicable Task Cards.• Manage materials and tools inventory. Show less

• Provided engineering support for the maintenance, repair and modification of Boeing 737-300 / -500 structures and mechanical systems. Provided support in the areas of hydraulics, materials and processes, fabrication and non-destructive testing.• Create Methods and Operations Sheets for structural repairs, Engineering Orders, Service Bulletins and Airworthiness Directives.• Prepare milestones in Microsoft Project and flowcharts for heavy maintenance and keep the process… Show more • Provided engineering support for the maintenance, repair and modification of Boeing 737-300 / -500 structures and mechanical systems. Provided support in the areas of hydraulics, materials and processes, fabrication and non-destructive testing.• Create Methods and Operations Sheets for structural repairs, Engineering Orders, Service Bulletins and Airworthiness Directives.• Prepare milestones in Microsoft Project and flowcharts for heavy maintenance and keep the process updated.• Design of structural repairs beyond manuals limits including nacelles components such as Thrust Reversers, Fan Cowls and Air Intake Cowls and obtain DER approval.• Research of technical approved data for analysis and the creation of technical documents for shop floor technicians.• Head of department with 4 Engineers and support in supervision of 25 O&R mechanics.• Ensure availability of tools, spare parts and materials required for heavy maintenance• Create and supervise the composites material shop. Show less

• Create operation sheets travelers (Technical Documents) for production floor technicians using Solumina and SAP Software.• Design of structural repairs beyond manuals limits for nacelles components such as Thrust Reversers, Fan Cowls and Air Intake Cowls and obtain DER approval.• Reverse Engineering with FaroArm Antrocam and Verisurf software.• Project Engineer on PW2000 Nacelle Program.• Project Engineer on V2500 Nacelle Program.• Project Engineer on PW4000 Nacelle… Show more • Create operation sheets travelers (Technical Documents) for production floor technicians using Solumina and SAP Software.• Design of structural repairs beyond manuals limits for nacelles components such as Thrust Reversers, Fan Cowls and Air Intake Cowls and obtain DER approval.• Reverse Engineering with FaroArm Antrocam and Verisurf software.• Project Engineer on PW2000 Nacelle Program.• Project Engineer on V2500 Nacelle Program.• Project Engineer on PW4000 Nacelle Program.• Technical support for sales and marketing areas.• Supervisor of 1 Engineer and 5 mechanics• Support Sales and Marketing Departments with brochures developments and visits to customers and prospects as a technical advisor.• Customer support on technical issues. Show less

• Create operation sheets travelers (Technical Documents) for production floor technicians using Microsoft Word and Excel.• Design of structural repairs beyond manuals limits for nacelles components such as Thrust Reversers, Fan Cowls and Air Intake Cowls and obtain DER approval.• Overhaul and Repair Engineer on Inlets, Fan Cowls and Thrust Reversers.• Responsible for CMM Faro-Arm operation for reverse engineering• Responsible for Autoclave Oven operation.• Responsible for… Show more • Create operation sheets travelers (Technical Documents) for production floor technicians using Microsoft Word and Excel.• Design of structural repairs beyond manuals limits for nacelles components such as Thrust Reversers, Fan Cowls and Air Intake Cowls and obtain DER approval.• Overhaul and Repair Engineer on Inlets, Fan Cowls and Thrust Reversers.• Responsible for CMM Faro-Arm operation for reverse engineering• Responsible for Autoclave Oven operation.• Responsible for conventional ovens operation.• Technical support for sales and marketing areas.• Support Sales and marketing departments with brochures developments and visits to customers and prospects as a technical advisor.• Customer support on technical issues. Show less

• A, B and Overnights checks on DC-9 equipment• Line maintenance including troubleshoot• Engines trimming• Brakes replacement• Minor structural repairs• On board mechanic on DC-9 equipment

• A, B, C and D checks on B-747, B-727, B-737, DC-10.• Rebuilt of and MD-90 for McDonnell Douglas.• Landing Gear Removal and Installation• APU Removal and Installation• Engines Removal and install• Flight Controls removal and install• Flight Controls trim• Minor Structural Repairs per SRM (Structural Repair Manual)