• Performed QA/QC inspections throughout the manufacturing, fabrication, installation, inspection, and functional testing of LV/MV switchgear, MCCs, Transformers, and other electrical equipment.• Ensured compliance with project specifications and national and international codes of standards during engineering, construction, inspection, servicing, and Factory Acceptance Testing of various electrical/instrumental and telecom equipment. • Created and reviewed inspection reports for accuracy and completeness.• Collaborated closely with the engineering team to identify and resolve any issues that arose during inspections.• Conducted walk-downs and created punch lists to address any outstanding issues.• Monitored closely to ensure prompt closure of punch items.• Trained and supervised junior inspectors and technicians to ensure adherence to safety standards and quality procedures.

Responsible for ensuring that work complies with applicable standards and Project Specs. Attended NOI request for FAT testing. Review the PO, Project Specs, Approved drawing, ITP procedure, QCP, MTC, and MDR to make sure proper and accurate documentation.

Monitor the demolition and removal of existing equipment for 65 units housing Project. Perform material receiving inspection prior to site installation. Monitor and inspect the installation of grounding system, raceways, circuit breakers, control panels, and cable installation per approved drawings and project specification. To verify RFI’s for any site modification. Monitor contractor’s work for conformance with the contract plans and specifications.

Prepare test related documentation, such as control plan for testing, test instructions and test records. Participate in meetings which have an impact on test activities held at the installation site. Set-up the necessary tools including associated calibration certificate for electrical testing. Execute the commissioning activities of the designated scope of works strictly following the Environmental Health and Safety rules and according to the quality standards. Issue weekly report to the Commissioning Manager including progress of works and forecast. Work closely with client site personnel and vendor service engineers engaged in pre-commissioning activities.

Performed quality control inspections and documentation in electrical & instrumentation activities for Zuluf Gosp3&4, and Abu Safah TP2&151/160 Project. Performed surveillance of subcontractor’s activities, ensuring that all E&I and telecom installation were carried-out in accordance with the approved construction drawings and specifications. Supervise the installation of the following instrumentation activities such as; cable pulling, cable tray, conduit, junction boxes, cabinets, air and impulse lines, mounting of instrument devices such as PT, LT, FT, TT, RTD and Thermocouple on furnace and boiler area. Supervise the installation of control valves, on-off, MOV, and ESD. Ensuring that it conforms to approved drawings and specifications. Recommend or provide solutions to the problems with Client approval through designated channels as per project specifications. Assessment of hazards and risks involved in the job and control measures to prevent or minimize the as well.

Monitored and inspections as identified in the approved Inspection and Test Plan (ITP). Performed incoming material inspection to ensure compliance with purchase order and specification requirements. Monitor and inspect the production quality to achieve the client requirements. Generated punch list items and NCR for any deviation against standard installation practice. Review of loop package for final acceptance prior to pre-commissioning on the field.

•Review of ITP / QCP for conformance to project specification, codes and standards.•Ensure work sequence is planned and controlled via implementation and adherence to client approved QCP’s and method statements.•Ensure that all works are inspected as per the requirements of approved quality and inspection test plan.•Responsible for the materials & equipment receiving inspection as per approved project specification prior to installation.•Inspection and verification of materials used to comply with aramco specification standard.•Materials receiving inspection of electrical, Instrumentationand telecom materials and equipments with the documents being verified if it conforms to the required specification of the project.•Inspects and witness all electrical, Instrument/telecom activities prior to raise RFI for aramco inspection.

•Materials receiving inspection of electrical, Instrumentationand telecom materials and equipments with the documents being verified if it conforms to the required specification of the project.•Inspects and witness all electrical, Instrument/telecom activities prior to raise RFI for aramco inspection.•Check all validity of calibration certificate•Perform inspection for electrical instrumentation/telecom installation such as trenches, stub up, sleeve, duct bank, and grounding conductor interconnection system, cad welding, and cable laying installation.•Witness related electrical & instrument cable like continuity and insulation test for LV/MV/HV cable and DC HI-POT for MV & HV Cable.•Conduct illumination test for lighting and polarity test for power outlet.•Witness grounding resistance test for all grounding network system.•Conduct inspection of LV, MV & HV Power cable, & instrument cables, cable tray & conduit including its supports (below & above ground installation)•Any deviation from drawings, plans, and standards coordination to sub-contractor to raise technical queries for clarification and approvals.•Inspect works and review checklists as per RFI submitted by sub-contractor.•Identify quality problems and suggest the solution.•Ensure that all works are inspected as per the requirements of approved quality and inspection test plan.

•Responsible for implementation of quality control procedure. •Identify defective works and prepare reports indicating the violations.•Issue NCR, DR, and reports for violations and submit to QA/QC supervisor.•Ensure corrective actions are performed as per the requirement of approved recommendations.•related electrical & instrument cable like continuity and insulation test for LV/MV/HV cable and DC HI-POT for MV & HV Cable.•Conduct illumination test for lighting and polarity test for power outlet.•Witness grounding resistance test for all grounding network system.•Conduct inspection of LV, MV & HV Power cable, & instrument cables, cable tray & conduit including its supports (below & above ground installation)•Any deviation from drawings, plans, and standards coordination to sub-contractor to raise technical queries for clarification and approvals.•Inspect works and review checklists as per RFI submitted by sub-contractor.•Ensure that all works are inspected as per the requirements of approved quality and inspection test plan.•Check all validity of calibration certificate•Responsible for the execution, implementation and review of inspection test plans.•Conduct daily monitoring at site and make records and reports of any deviation made from approved drawings, specification and or not compliance to approved materials are being used at job site or any defect/damage cause by wrong application installation and accidentally cause.

•Perform inspection for telecom trenches, duct bank and fiber optic installation as per IFC drawing•Inspect site installation with in compliance with the requirements and specification.•Inspection & check equipment mounting & assemblies if comply as per IFC drawing at designated location.•Perform Inspection of CCTV installation for AFK oil/utility wells heads, •Conduct inspection of marshalling cabinets, console installation and termination.•Prepare schedules, progress report, as-built plans & responsible for all materials required on site & attend daily site co-ordination meeting with clients & consultants.•Review plan as per standard and specifications of materials.•Responsible for the materials & equipment receiving inspection as per quality assurance manual and quality control inspection plan.•Conduct inspection activity and surveillance to project.•Prepare daily inspection documents prior to project completion and hand over the project.

•Responsible for electrical/Instrumentation system inspection, preparation of document for all construction activities as per PQP and ITP Requirements.•Responsible for implementation of quality control procedure, with project specification and standard.•Conduct pre-inspection with subcontractor QC prior to release for next activities. •Daily site inspection to assure work quality & workmanship.•Conduct internal inspection among all activities.•Conduct & initiate inspections as per approved design drawings (IFC), ITP & QCP, procedure.•Review of ITP / QCP for conformance to project specification, codes and standards.•Ensure work sequence is planned and controlled via implementation and adherence to client approved QCP’s and method statements.•Perform Inspection of the exothermic weld, test pin station and bonding box as per aramco standard.•Review the scoop of work and list all construction plan drawing.•Assist any Installation of cathodic protection, to ensure that suitable for the requirement of aramco standard. •Perform Inspection of the magnesium anode and deep anode bed Installation to make sure the pipelines are protected by cathodic protection.•Surveillance and Inspection the excavation of trench for the direct buried cp cable & duct bank as per aramco standard.•Survey the monthly Potential test of all test pin station to make sure that pipelines are protected by cathodic protection.•Inspect installation and termination of switchgear, MCC, power & lighting panels, IRP & transforme.•Conduct illumination test for lighting and polarity test for power outlet.•Witness grounding resistance test for all grounding network system.•Check all validity of calibration certificate•Daily site inspection to assure work quality & workmanship.•Inspect site installation with consultant & clients in compliance with the requirements and specification.

•Responsible for electrical/Instrumentation system inspection, preparation of document for all construction activities as per PQP and ITP Requirements.•Responsible for implementation of quality control procedure, with project specification and standard.•Assist any Installation of cathodic protection, to ensure that suitable for the requirement of aramco standard. •Inspection & check equipment mounting & assemblies if comply as per IFC drawing at designated location.•Perform Inspection of the exothermic weld, test pin station and bonding box as per aramco standard.•Review the scoop of work and list all construction plan drawing.•Inspection of Cathodic protection system like rectifier transformer, anode beds test, test station bonding station for pipeline & plant facilities including tanks•Perform Inspection of the magnesium anode and deep anode bed Installation to make sure the pipelines are protected by cathodic protection.•Surveillance and Inspection the excavation of trench for the direct buried cp cable & duct bank as per aramco standard.•Survey the monthly Potential test of all test pin station to make sure that pipelines are protected by cathodic protection.

•Verifies material and construction product compliance to Quality Standards by executing the inspection, testing and documentation•Conduct Inspection the installation of marshalling cabinets/distribution panels/junction boxes/cable tray/conduit(UG/AG), pulled cables, meggering testing and termination and commissioning.•Conduct Inspection the installation of instrument piping system (Pneumatic and impulse lines), bench and site calibration of instruments such as Flow Transmitters, Temperature Transmitters, Level Transmitter, and Pressure Transmitter, Differential Pressure Transmitters, Control Valve, On-Off Valve, Pressure gauges, Temperature elements, Level indicators, Limits switches etc.

•Supervised the implementation of the project according to the plan.•Inspection & witness test of XLPE medium voltage Pirelli power cable, rated 35KV.•Witness & inspection of Medium Voltage XLPE power cable termination and torque testing. •Witness & inspection of medium voltage switchgear, 34.5KV. simulation test.•Inspection of panel boards installed in some units.•Simulation witness & testing of Power outlets & switches. For residential units.•Witness & Inspection of switchgear pre-commissioning.•Prepared list of materials needed on the site and order to main office and assure to finish the project on or before schedule.•Conducted all safety precautions, such as protecting clothing safety guards and all other regulation for purpose.•Interpret drawing on site and prepare and material list on order.•Assist and provide technical support to the project manager.•Prepared as built drawing in electrical at the end of project