Rory James Bury Email & Phone Number

Bendigo, Vic, Au

Australia

-Commissioning, servicing, and repairing grid-scale inverters.-Install and set up equipment at customer sites.-Maintain and repair equipment to ensure functionality.-Troubleshoot technical issues and perform necessary repairs.-Provide customer support and training on equipment usage.-Replace major components such as stacks and 3-phase fans.-Transformer oil sampling and RMU maintenance/repairs.-Interrogate MODBUS and CANBUS controlled equipment.-Travel to customer locations as required.

Ballarat, Victoria, Australia

Moorabool South Wind Farm/Biala Wind FarmGoldwind 3MW platform-Testing of lights and reciprocals-Insulation resistance tests of generator windings-Installation of temporary wiring in tower sections/nacelle-Function testing pitch belt systems-Assembly of weather stations on nacelle roof-Wiring and operation of the nacelle yaw system-Running and connecting service lift wiring-Hytorc blades/hub-Cable Drops

Ararat

75x GE 3.2MW Assisting in mass pitch battery change-out and additional tasks• Replacement of worn pitch batteries• Undertake retrofitting tasks in nacelle• Lubrication of bearings/gearing up tower• Participation in annual maintenance• Replacement of climb assist system• Fault-finding circuits

South Australia, Australia

Commissioning of 35x 3.6MW Senvion 3XM EBC turbines-Adjustment of motor encoders/limit switches.-Insulation resistance tests of 33kV cables.-Correction of proximity transducers.-Electrical/mechanical fault finding.-Installation of turbine retrofits.-Assisting construction with temporary wiring/repairs.-Non-Conformance Reports/QA inspections.-WTG walkdowns with clients-Participate in break-in maintenance

Bulgana, Victoria, Australia

Commissioning of 54x G132 turbines. -Verifying function of emergency circuits-Full checks/tests of hydraulic circuits-Configuring/loading parameters onto PLCs-Performing test runs on WTGs-Setting of transducers/sensors according to spec-Function testing fans/heaters-Visual checks of all fittings/fixtures-Insulation resistance testing generator/transformer-Initiating/observing 240 hour run tests-Completing reports/punchlists-Check/operate HV switchgear-Write out SWMS/JSAs-Working under permits as recipient in charge

South Australia, Australia

Construction experience with GE 3MW platform turbines• Blade Installation• Producing SWMS/JSAs for Tasks• Terminating Temporary Power Cables• Electrical Fault Finding• Small Component Change-out• Craning/Pitching/Yawing Turbine• Rattling/Hi-torqueing Bolts• LOTO Procedures/HV Permits/Recipient in Charge• Dogging/Banking loads• Blade Repairs• Assist in Non-destructive Tests (NDT)• Replace Service Lift Cables• Installation of Hydrologic Turn Drive Unit• Use of Hydraulic Cassette• Punchlist/Cleaning/Mechanical Completion

Hallett, South Australia, Australia

Construction experience with GE 3MW platform turbines at Silverton Wind Farm and Willogoleche Wind Farm

Hallett, South Australia, Australia

Willogoleche Wind Farm/Silverton Wind FarmWorking as an electrical tradesperson/mechanical trades assistant.-Termination of 6KV Cables-Terminating With Cold-Shrink/Ramset Joints-Hydraulic Tensioning of Bolts on Base Ring-Caulking Tower Flanges-Paint Touch-Ups-Generator Alignment-VLF Cable Testing-Insulation Resistance Testing-Cable Securing at Heights-Pre-Installation-Base Surveillance/Leveling-HV Cable Replacement-Bolt Torquing on Upper Sections-Dogging/Banking Small Loads

Mount Millar Wind Farm

• Troubleshoot or Repair Mechanical or Electrical Malfunctions Related to Variable Pitch Systems, Variable Speed Control Systems, Converter Systems, or Related Components.• Climb Wind Turbine Towers to Inspect, Maintain, or Repair Equipment.• Diagnose Problems Involving Wind Turbine Generators or Control Systems.• Perform Routine Maintenance on Wind Turbine Equipment or Fiber Optic Sensing and Control Systems.• Replace Worn or Malfunctioning Components.• Start or Restart Wind Turbine Generator Systems to Ensure Proper Operations.• Metering of Electrical Components.•Lift Drive/Rope Replacement.•HV Operations/Permits/Recipient in Charge.•Repairing pitch boxes/capacitor boxes/Nacelle Fans.•SF6 Replacement for Switchgear. •Rectifier Overhauls.•Hub Replacement•Dogging/Craning•PPE Inspection•Fire Extinguisher Inspections/Tests.•Overspeed/Chopper/Capacitor/Emergency Tests.•Remote SCADA/Emergency Callouts.• Stocktake.•Testing/Refurbishing of IGBTs/SCRs/Thyristors/Capacitors/Resistors/PCBs.•Assist with Anchor Point Load Testing.

Mount Millar Wind Farm

Participating in relevant electrical activities as a Wind Turbine Technician

Mt Millar Wind Farm

Service, fabrication and repairs on 35 Enercon E70 direct drive turbines

Certificate Iii, Electrotechnology, A

Activities and Societies: -36 weeks study on campus -Three weeks secondment with domestic/commercial based A class electricians.

Certificate Ii, Electrotechnology

Prevocational course. Progressed to certificate III

South Australian Certificate Of Education

Activities and Societies: Australian Rules Football, Cricket, Student Representative Council President Completed Year 12