Worked in various of engines like Rolls Royce AVON 200 (phase 1 & Phase 2), Pratt & Whitney GG4C, GE LM2500 & LM6000.Routine Monthly (700 hours), 4000 Hours PM & 8000 Hours PM activities.Involved in engine replacement Pratt & Whitney GG4C, GE LM2500, GE LM6000 & Rolls Royce AVON 200.Proficiency in SAP & MAXIMO 7.6.Monthly inventory follow-up.Involved to replace water injection HP cartridge Sulzer pump.Involved in PT (Power Turbine) Replacement (both dismantling & erecting).Involved in several corrective maintenance like air-intake house filter replacement, pump replacement, bleed valve replacement, IGV Replacement, Lube oil filter replacement, cooler replacement, etc.Involved in Mechanical Isolation (spading & De-spading) , purging gas & checking the H2S Level.Routine 700 Hours PM Activities like GG Detergent wash, Bleed valve inspection & IGV Critical checks.Involved in Hydrotest for the spools and field lines.Managing work orders, Daily reporting & Manhours entry (using SAP & MAXIMO 7.6)Involved in Replacement of IGV & Bleed valve ( ROLLS ROYCE AVON 200)Performed PT (Power Turbine) exhaust inspection.Performed Engine alignment methods using Laser alignment , Dial indicators & Straight edge alignment.Performed GG & Alternator lube oil Tank inspection.Managing & Maintaining all the materials Related to the various engines (Using SAP & MAXIMO 7.6)Maintenance and service of Centrifugal Pumps, Screw pumps, reciprocating Pumps, heat exchangers, high pressure reactor.Routine valve and pump maintenance.Pump- motor Alignments.Involved in shutdown and break down jobs of pumps and other rotating equipment.Spading and DE spading.Performed fixing and removing demister pads.Receive work schedule from supervisor and coordinates all activities with operators and follow the work.Maintenance and service of Centrifugal Pumps, Screw pumps, reciprocating Pumps, heat exchangers, high pressure reactor, Gear Boxes.

Project : HPCL Vishakapattanam Revamp 05 ProjectFit-up & weld visual inspection piping as per ANSI/ASME B31.3 Preparation of Inspection and Test Plan, checklist, procedures and review of construction drawing.Control of quality for piping fabrication such as fit-up, visual and dimensional inspection conforming to approved for construction drawings.Responsible for issuance of Non – Conformance Report if any violation and out of standard for piping works.Line flushing, air blowing; pressure testing, piping lay-up inspection, relief valve installation, re-instatement and final inspection for mechanical completion.Responsible for inspection of pipe spools for shop and fabrication such as fit-up, dimensional and visual inspection as per Client StandardsPrepare Request for Inspection(RFI) to Third party Inspection(TPI) and Project Inspection Division through Quality Management Information system(QMIS)Preparing Bill of material (BOM) with respect to the ISO Drawings & flange box up checklist/Torquing checklist.Preparing inspection reports for fit up & welding.Preparing NDT Request as per the client standards.Fit up inspection & orientation checking.Preparing Mechanical clearance certificate and witnessed hydrotest (hydrotest pressure set by client standard)Control of Weld quality as per approved QC Procedures and Standards and maintain QC records.Familiar with weld defects.Maintain documentation as per the Client requirement.Conducted surveillance of Welding, NDT, PMI and PWHT Activities on Subcontractors Designated Area of Responsibility.Ensures that all welds meets the Project Requirements and in accordance to the WPS . Implement the Project Construction Quality Program at site. Ensures that repairs are done correctly and accurately to comply with the Project Specification. Implement the Quality Control Intervention points on the Inspection and Test Plans, ITP (Surveillance, Witness, Hold Point and Record Review).

Project: Shutdown Turnaround (HF Pipeline) Client: Reliance industries, Patalganga, Mumbai, IndiaPerformed RF pad leak testing as per applicable QCP.Monitoring PWHT and review & PWHT reports and chart.Material receiving and inspection of Flange and fittings.Familiar with Welding Inspection, Welding procedure selection, Welder Qualification, Selection of Electrodes, Visual Welding Inspection, Pre & Post weld scanning etc.Preparation of Inspection and Test Plan, Checklist, Procedures and review of construction drawings.Responsible for QA/QC piping inspections, shop piping spool fabrication and field installation, laying and assembly inspection, fit-up, alignment inspection and testingFamiliar with Material Inspection Dimension Check and documentation as per construction materials standardsExposure in ASME SEC IX & API 1104 for welding qualification (procedure and performance) and in inspection.Familiar with Welding Inspection, Welding procedure selection, Welder qualification, selection of electrodes, Visual welding inspection, Pre-&post weld scanning etc.Knowledge in Radiographic interpretation of weld jointsValid certification in UT/RT/MT/VT/LT reviewing and its documentationKnowledge in fabrication of piping, structure, pressure vessel and other equipment's, documentation of history sheets, P&IDConfident to handle the construction and quality control activities as specified in the drawing and applicable standards and specifications &Familiar with NDT methodsInterpretation of construction drawing like ISO and P&ID and give instruction to the construction teamWitnessed NDT inspection like PT, MT, RT, UT. Coordinating NDT activities with Third Party NDT CompanyEnsuring implementation of QCP and ITP.Co-ordination with client inspector for final inspections for Hold and Witness Point inspection.Preparations of quotations, variations, substantiation and running bills of concerned projects.

Conducted surveillance of Welding, NDT, PMI and PWHT Activities on Subcontractors Designated Area of Responsibility.Ensures that all welds meets the Project Requirements and in accordance to the WPS . Implement the Project Construction Quality Program at site. Ensures that repairs are done correctly and accurately to comply with the Project Specification. Implement the Quality Control Intervention points on the Inspection and Test Plans, ITP (Surveillance, Witness, Hold Point and Record Review). Receives Test Packages for Line Checking, Document Reviews and Punch Listings. Performs Actual Site Line Checks and Verification as per Approved Isometric drawings. Final Release and Sign¡ngoff of Test Packages.Witness Air Blowing, Hydro Test, Service Test, Pneumatic Test and Flushing. Visual inspection of Cement line Joints.Ascertains that Safety for Welding, Testing and Related Activities are being implemented.Performed NDT Request to Third Party Inspectors (TÜV Rhineland).