Simone Giancane Email & Phone Number

Lecce, It

Brindisi, Italia

Firenze

Italy

- Structural Optimisation of an excavator: defeaturing of the original model (NX Unigraphics); mesh definition (Ansys WB), run and analysis of FE model (Ansys). Verification of welding joints.- CAD and FEM training at the course of “CAD and FEM Techniques” (project: ES.T.RE.MA. – Repair and Diagnostics of Aircraft Engine Components) coordinated by University of Salento (Lecce).

Dept. Engineering Of Innovation – University Of Salento (Lecce)

Fixed Term Contract. Main tasks:- Mechanical Testing on composite and metallic materials (for Avio SpA (http://www.aviogroup.com/it/), Bombardier Inc. (http://www.bombardier.com), Alenia Aeronautica SpA (http://www.finmeccanica.it/Corporate/IT/Corporate/Settori/Aeronautica/Alenia_Aeronautica/index.sdo): High Cycle and Low Cycle Fatigue (room-temperature and high temperature) on Nickel Superalloy, UDIMET, Renè, Waspaloy, Nimonic Single Crystal; Creep test on Nickel Superalloy, UDIMET, Renè, Waspaloy, Nimonic Single Crystal; Open Hole Compression, Bearing Bypass, Fatigue test on CFRC.- Implementation of Matlab routines for experimental data elaboration, statistical analysis and presentation of results.- Design of tools and facilities for test execution according to ASTM and Boeing standard;- FE Structural analysis of support equipment and structural parts (composite and metallic materials).- Catia v5 training for the course of CAD (Faculty of Mechanical Engineer of University of Salento). Academic years: 2009/2010, 2010/2011, 2011/2012.- Research on the behaviour of composite materials by means of optical and infrared non-destructive techniques.- Participation at several national and international scientific conferences.- Publication of scientific papers on international journals.

Italy

Lectureship at the Advanced Engineering course of the Postgraduate school of the University of Salento.Title of the course: Advanced CAD techniques (Catia v5).Duration of the course: 60 hours.

Lecce, Italy

Lectureship at the courses of CAD Modelling (Catia v5) and FE Analysis (Ansys) at the University of Salento (Faculty of Mechanical Engineering and Industrial Engineering);- Design of tools and facilities for test execution according to ASTM standard;- Research on the behaviour of composite materials by means of optical and infrared non-destructive techniques.

Brindisi, Italy

- Design and prototyping of a UAV (Unmanned aerial vehicle);- Implementation of the production process;- Structural and modal FE analysis of the aircraft structures and of the equipment employed for flight simulation and mechanical test.

Lecce, Italy

Implementation of software for the rapid creation of a FE mesh for aircraft critical parts. Industrial partner: AGUSTAWESTLAND SpA (http://www.agustawestland.com/). The final result is the development of software for design of a helicopter fuselage starting from simple geometries. The output file can be chosen to be suitable for Nastran/Patran or Ansys.

Italy

Among projects:- FE Structural analysis (ANSYS) of a telescopic Telehandler for several work configuration (customer: CNH – Case New Holland (www.cnh.com)).- Modelling and design (CATIA v5) of press moulds for an aircraft rear (customer: AugustaWestland SpA).- Modelling and design (CATIA v5) of equipment for HF antenna support positioning on helicopter fuselage (customer: AugustaWestland SpA).- Iges surface generation (3D Reverse Engineering) of a mould surface (customer: Augusta Westland SpA).- Modal analysis of a gearbox (ANSYS) mounted on the diagnostic railway car, ROGER SBB (customer: MerMec SpA(http://www.mermecgroup.com)).- FE structural analysis (ANSYS) of the GEnx oil tank mount system under a Fan Blade Out load (customer: Avio SpA).- Modal and impact analysis (ANSYS) of a FREMM GT MODULE modelled with lumped mass method in several configurations of engine mount system (customer: Avio SpA).- Rotor-dynamic Analysis (ANSYS) of the system composed by: LM2500 Horizon engine + HSCS coupling shaft + Reduction Gearbox. Estimation of critical speed and frequency response in several configurations (customer: Avio SpA).

Achievement Of The Title Of Fellow In Mechanics Of Materials, Experimental Mechanics, Cad Modelling

Phd In Mechanical And Industrial Engineering, Phd - Xviii Cycle

Degree In Engineering Of Materials, Engineering Of Materials