Thim Elver Kristensen Email & Phone Number

København, Hovedstaden, Danmark

Copenhagen Area, Capital Region, Denmark

As a System Engineer there are a lot of different tasks and a broad overview of the whole radar system is required, both in hardware and software. Right from the general knowledge of firmware to the detailed setup of the user application software, as well as hardware components and their signal paths. As the radar systems are all over the world and many tasks are preformed at the customer location, there is a lot of travel and planning of activities in cooperation with the customers.The… Show more As a System Engineer there are a lot of different tasks and a broad overview of the whole radar system is required, both in hardware and software. Right from the general knowledge of firmware to the detailed setup of the user application software, as well as hardware components and their signal paths. As the radar systems are all over the world and many tasks are preformed at the customer location, there is a lot of travel and planning of activities in cooperation with the customers.The variety of tasks including their planning and execution is, but not limited to:● System testing and bug reporting / design improvements suggestions.● Hardware / Software upgrades with accompanying setup and verification.● Reading customer requirements and agreeing on test methods to verify a given requirement.● Preforming FAT (Factory Acceptance Test) at Weibel Test Center together with the customer.● Preforming SAT (Site Acceptance Test) at customers test facility.● Providing customer support either at customer site or online.● Doing scheduled preventive maintenance and calibration at customer location.● Training / teaching how to use and maintain the radar systems both for customers at customer location and internally.● Making and maintaining training material. ● Doing ad hoc repairs at short notice anywhere in the world for support of critical missions. Show less

Københavnsområdet, Danmark

At Natus Neruology I worked with a mix of hardware and firmware which was thoroughly documented and tested according to the applicable directives. Support and sustainment tasks of various products. Also travelling to Gort - Ireland production facility every few months to support with work instructions, testing and documentation.

Københavnsområdet, Danmark

Development and execution of electronical and mechanical testing using relevant software/firmware.Accelerated Stress Testing (AST) (HALT/HASS). Documentation and reporting of test results.Tools used:● LabVIEW - Test execution & monitoring● Atmel Studio 6 - C programming● RealTerm - Data logging● Eagle - Schematic drawing & PCB design● KiCad - Schematic drawing & PCB design● LPKF ProtoMat E33 - Milling PCBI finished my bachelor of engineering thesis in… Show more Development and execution of electronical and mechanical testing using relevant software/firmware.Accelerated Stress Testing (AST) (HALT/HASS). Documentation and reporting of test results.Tools used:● LabVIEW - Test execution & monitoring● Atmel Studio 6 - C programming● RealTerm - Data logging● Eagle - Schematic drawing & PCB design● KiCad - Schematic drawing & PCB design● LPKF ProtoMat E33 - Milling PCBI finished my bachelor of engineering thesis in cooperation with Radiometer Medical ApS with a 12 (A).It was about digital control of a brushless sensorless DC motor, using the back electromotive force to time the commutations, while taking the varying load into consideration. Also using the back electromotive force to measure the impact of a change in load. Show less

Tanzania

During my education at KEA, I was hired by ULD-80 Karagwes Venner, which is a non-governmental organization (NGO), in collaboration with KEA, to do my internship as a teacher. It was done at a vocational school in Karagwe, which is a small village in Tanzania. Here a colleague and I supported the local teacher. We taught electronics students about digital electronics mainly and some about embedded software/hardware. The students aged 19-26. The teaching was a mix of practical exercises and… Show more During my education at KEA, I was hired by ULD-80 Karagwes Venner, which is a non-governmental organization (NGO), in collaboration with KEA, to do my internship as a teacher. It was done at a vocational school in Karagwe, which is a small village in Tanzania. Here a colleague and I supported the local teacher. We taught electronics students about digital electronics mainly and some about embedded software/hardware. The students aged 19-26. The teaching was a mix of practical exercises and related theory. The teaching was finalized with an examination. Show less

Danmark

Repair, calibration, maintenance and upgrades of the Air Force's electronic and IT equipment. Also helped as an assistant teacher at a radar system course.Worked with: ● Satellite, Radio and Telecommunications Equipment● Computer Network Equipment● Command and Control Systems● Radar Systems● Software/Firmware● Physical Training InstructorInternational experience acquired in:● Norway - Training● Portugal - Exercise● Afghanistan - Deployment… Show more Repair, calibration, maintenance and upgrades of the Air Force's electronic and IT equipment. Also helped as an assistant teacher at a radar system course.Worked with: ● Satellite, Radio and Telecommunications Equipment● Computer Network Equipment● Command and Control Systems● Radar Systems● Software/Firmware● Physical Training InstructorInternational experience acquired in:● Norway - Training● Portugal - Exercise● Afghanistan - Deployment, Danish Radar Information System (DARIS) Show less

Bachelor Of Engineering (Beng), Electrical Engineering, 12 (A)

Activities and Societies: Study Council

Academy Profession Graduate (Ap), Electronic Technology, 12 (A)

Activities and Societies: Showcased final study project at KEA Connect, March 2013, and again at Computerworld Expo, April 2013.

Erhvervsuddannelse (Eud), Electronics Technician

Activities and Societies: Representative of the Armed Forces education programs at Værløse Air Base - Airshow June 2002