Timothy Litzinger Email & Phone Number

Baltimore County, Maryland, United States

Maryland, United States

Bethesda, Maryland, United States

Baltimore, Maryland, United States

Baltimore, Maryland Area

I worked in the underground tunnel fabricating and installing most of high temp pipes up to 12 inch schedule 80. I used high low guages to make our fits. ALL FITS WERE X RAYED . I HAD ZERO FAILURES! I installed calcium carbonated slides, glides and anchors. I was put in charge of running a small man crew to pipe in the 2nd and 3rd floors. We ran 4 inch chilled beam supply and return lines. Burned in most of thread o lets for the copper tie ins. I helped install 10 variuos sized pipes in riser shafts that totaled about 1000 feet of vertical pipe. I also did some copper work like sweting and propress on chilled beam side. I am currently in mechanical room doing high temp tunnel tie ins to vertical riser shafts on heat side. I was also on the Federal post office facility vehicle maintanance job in downtown Baltimore doing screw pipe up to 2" . This facility has over 3000 feet of pipe for its mechanics. Which include automatic transmission fluid, winshield wiper fluid, various weight motor oils and compressed air systems.

Greater Philadelphia Area

Shrewsbury, Pennsylvania

building johnson controls new facility in york pa. This job IS where they will build and test chillers that go in all the new navy vessels, I help install all of the 32 inch vitaulic pipeon this job, I swung and erected most of the steel in the building and up on roof to secure smoke stacks and gas block vents, I installed most of the 30 or so armstrong pumps that run the testing facility. I have upwards to 300 plus hours on acetelyne torch work fabricating various sized pipe stanches/supports going to all testing pumps. I did most of a LP gas lines going to the cup. I also piped in the 12 and 14 inch pipes that are in the final testing rooms . i did the smaller dimeter pipes that feed the 32 large 10 x 12 coils used to cool the new chillers.

Philadelphia Pa

Getting project done on time and under budget, I would focus on customers wants and needs then satisfy them with job well done.

Edgewater N J

FOREMAN/ LEAD MAN

Edgewater Park Nj

LIDESTRI- I piped in 6 inch stainless pipe in processing facility. I piped in armstrong pumps and did 1/4 inch screwpipe for gauges, I helped pipe in heat exchanger in vitaulic pipe. I did small propress for water lines. I piped in steam traps. I fit and piped in 3 and 4 inch stainless sanitary tubing .I piped in 3/4 inch copper air lines.BARRY CALLEBAUT-I piped 4 inch schedule 80 pvc drain lines and installed sump pumps for that project in the chocolate factory. I installed new 8 inch duct work for fresh air system. I ran 3 inch sch 80 screw pipe for new melter system. I fabricated and installed new stainless pipe for new conveyor system. I cut in new valves and installed new piping for melter tanks. I helped change out various sizes screws that move product from pump to overhead conveyor belts. I installed several different motors, pumps and bearings too. I installed 200 feet 3" sch 40 screw pipe with valves for new device in processing room.PURATOS- I piped in a temporary boiler for shutdown which included setting portable boiler outside, punching holes in outside wall for steam, condensate,city water and drain lines. I ran various sizes of stainless steel sanitary tubing for new holding tanks. I aided crew from Germany with installation of mechanical motors in elevator chases. I installed and fixed safety cages surrounding elevators. I ran 3inch air line header for new equipment. SUNOPTNA- I was in charge of running 180 feet of 24" Victaulic pipe. We added new pipe to bolier for new system install which included carbon steel pipe sizes from 6", 8",10" and 12". I installed all pipe anchors and guides along with copper lines for soft water system. I installed new larger blowdown tank to accommodate larger systems needs.ARYZTA- I was lead man on job for millwright work including preventive maintenance task on plumbing,panners, proofers&starter room tanks,I worked on replacing hytrol&capway conveyor belts,motors, bearings,gears,chains,screws&rollers

Newport Delaware

We built 2 tank farms @ croda site. We erected steel structures to enclose tank farm vessles. Piped in 2 inch sch 80 pipe. Piped in sch 10 stainless process pipe for product. I was also involved in the underground piping job for the university of Delaware. That consist on 2000 inches of welds. We ran 6 inch sch 160 condensate and 10 inch sch 80 steam pipe . I did all of the foam richwell insulation on underground pipe and We piped in 6 manways to tie them all together. I was trained in trenching, confined space, scaffolding , personla fall protection, safety tripod persinal removal and how to use and read air monitoring devices. I also dug footers for a 125 ton gantry crane in the shop, I used pnematic tampers to pack soil for crane footers. I also worked at the pampers baby wipes facilities in dover delaware. We demo an old facility and installed a new high speed line... I got a chance to use a hover jack to move equipment to and from job. I worked praxair shutdown removing all PRESSURE RELEIF VALVES (PRV). I got a chance to use torq multiplier. I used crane to Remove and istall inkanel fire ring for burner system. I removed 1 ton manway covers for inspection and preventive maintenance. I fabricated burper hold down trays for smoke stacks

Wilmington, Delaware

UNIVERSITY of DELAWARE-I helped build the University of Delaware college dorm job. We ran 4,6 and 10 inch pipe. I fire caulked 2000 penetrations. I laid out the entire mechanical room in dorm B. I piped in steam traps in dorm A. I installed pipe guides and anchors. I ran 3/4 copper water lines. I installed duct work with tin knockers on the weekends.We ran all large diameter pipe in basement for boilers and chillers. I fabricated and installed all spider pipe guides and anchors.VETERANS HOSPITAL- I installed all steam traps for mechanical rooms and installed orifice plates @ high pressure steam station. I piped in air handlers on roof and ran various screw pipe jobs .I sweat over 300 feet of copper lines on 3 different floors. I used propress for nwater fountain installs and helped fire protection crew install sprinkler heads and screw pipe.

Newark, Delaware

SCIENCE RESARCH LAB...I piped in airhandlers in penthouse. 4 and 6 inch pipe. I formed all nursing pads for air handlers. I built steam traps for boilers. I did mechanical room in basement. I worked in equipment yard doing inventory in shipping and receiving for quality control. I did the pipe spider guides and anchors. I did pioe in elevator chase. I helped install pipes under walk way/bridge. I used crane to fly parts and material on roof . I did fire caulk on wall penetrations. I did small diameter core drilling on floors and roof for risers.

Edgewood, Maryland

D.O.D JOB..... THIS JOB WAS OVER A MILLION SQUARE FEET OF PIPE. .... I helped install 48 inch headers with 36 inch risers to 3 chillers. I also helped pipe in series 5 HURST boilers on DOD ARMY BASE. I was responsible for doing the 4 inch sch 160 condensate lines . I also piped in most of steam traps with high forged steel fittings. I did alot of bevel torch cutting for my welders to speed up the job. I also helped pipe in the cooling towers on the roof.I rigged pipe for crane and used hand signals for installation of prefabricated pipes and was trained on safety tripod for proper removal of coworkers in case of emergency for underground manhole pipe project. I was also trained to use personal air monitors for this exercise

Baltimore, Maryland

Shock trauma hospital. ... I piped in the entire 8th floor penthouse pipeng system loop. I piped in Armstrong pumps, 3 air handlers and chiller system. I. Workwd with 8 ,10 and 12 inch pipe. I helped plumbers install waterblin3s for the heated helicopter pad on roof. I did a lot of small socket welded pipe on the 5th floor. I also piped in some ionized plastic pipe on 5th floor. I helped plumbers attach fixtures in bathrooms. I did some 14 and 12 inch pipe in basement mechanical room. I used torch to bevel large Diameter pipe on basement project.

Baltimore Maryland

Mercy hospital. ... I was sent down there to install steam traps. I also piped in the entire 7 th floor 4 inch supply and return lines . I also solder alot of 1/2 and 3/4 inch water lines foe the plumbers. .. on the weekends I helped tin knockers install some duct work. I piped in the fuel lines from street side fuel tanks to hospital temp generators. I finished up with. Fabricating spider guudes and pipe anchors. I helped plumbers cut and install cast iron pipe with no hub bands

Aberdeen, Maryland

I learned to do layouts. I was trained in a vitaulic school for pipe grooving. I acquired my osha 10 certification from this job. I was also taught how to run a straight mast elevator and buck hoist. I learned how to pipe weld. I ran small screw pupe foe boilers. I helped puoe in air handlers on roof top of 3 buildings . I ran 4,6,8,19,24 and 36 in pipes. I pioed jn a glycol system for the chillers. I piped in some of the steam traps on bouler side. I buikt and in stalled expansion loops and fabricated and buikt all pipe spider guides and anchors. I pressure tested alot of the plumbers water lines. I learned to use core drilling machine up to 36 inch. I also learned to fire caulk penetrations on all hallway pipes

Pipefitting/Pipefitter And Sprinkler Fitter

PIPE WELDING 101 AND 201

Heavy Duty Diesel Mechanic, Mechanics And Repairers, General

Mechanic