Tio Fallen, P.E. Email & Phone Number

Melbourne, Victoria, Au

Melbourne, Victoria, Au

Delivery GOM Trinidad Team

Melbourne, Victoria, Au

Mechanical Engineer – Angostura Phase 3 Project Trinidad and Tobago- Responsible for mechanical discipline engineering for Design and Execution of the Angostura Phase 3 topsides facilities modifications and subsea flowline & riser commissioning.- Package Lead for the ASME B31.8 pig receiver design and installation including review of Skid Design, Weld and NDE Procedures, B31.8 Code Calculations, and Pipe Stress Analysis- Co-Authored User Design Specification for 2Phase Inlet Separator per ASME VIII Division 2 Code included Post Weld Heat Treatment procedure, NDE requirements, and material selection and specification.- Provide discipline engineering expertise for piping modification design and constructability including field weld optimization, workpack development & review, and NDE & hydrotesting philosophy- Commissioning lead for subsea riser & flowline subsea tieback to topsides facilities including design & installation of subsea to topsides riser tie-in spool and execution of commissioning philosophy e.g., leak testing, and dewatering of flowline/riser.

Melbourne, Victoria, Au

•Part of offshore management team completing; safety audits and toolbox talks, HSE incident investigation lead and team member, JSA’s, planning support and supervision of contractors and vendors to support achieving Zero Harm business objective•Support System Custodians in the overall assessment of the performance of Safety Critical Systems against the set standards established as part of the Safety Case•Liaise with the onshore Project Engineer and PU planning function to effectively plan, implement, test, commission and close out MOC scopes of work; offshore owner of controlled critical documents, P&ID’s, Safe Charts and C&E’s•Provide input into multi-discipline engineering projects, both small and large, support HAZOP/hazard review processes and constructability and operability reviews. Develop and implement minor plant modifications for offshore and onshore sites in line with Management of Change procedure.•Provide day to day engineering support; troubleshooting operational and equipment issues, liaison back to Technical Authorities, (site engineering surveys and audits) and contractor and vendor support•Process optimization; review and optimization of process monitoring models for topsides and subsea systems•Direct supervision of contractor and vendor resources•Development and optimization of maintenance routines and work packs to support continuous improvement of facility reliability•Training and mentoring operations and maintenance personnel; role out of engineering strategies, presentation of incident findings•Production loss incident investigation leader

London, England, Gb

• Managed the $1.5MM maintenance overhaul of facility mooring - hydraulics system; including development of AFE, overhaul maintenance strategy, engineering work-packs, and execution schedule and delivery • Conducted Fitness for service calculations/assessments on ASME VIII coded vessels and ASME B31.3 piping; resolved integrity issues with fuel gas scrubber, flare piping, aviation fuel lines, nitrogen line, 316 SS tubing, and seawater service piping. (Working knowledge of API 510, 579, 570/74, ASME Section VIII, B31.3, & PCC-1&2 standards) • Initiated preventive maintenance program to repair & provide recordkeeping of service for over 120 safety critical pressure relieving devices per API 510 standards; developed baseline survey for psv testing and maintenance.• Conducted root cause failure analysis of rotating equipment, mechanical integrity, & loss of primary containment failures; applied methodical problem solving which resulted in successful reduction of pump seal failure rates; implemented recommendations for tubing installation to remediate blowout occurrences, and revised torque specifications for shell to channel flanges on shell and tube heat exchanger to eliminate known gas leak. Updated site specific controlled design specifications to align with industry Standards and best practice • Responsible for the engineering design and construction of facility projects ranging from piping & tubing replacements and installs, packaged equipment decommissioning, & pressure vessel code repairs. • Verify and coordinate - MOC processes including active participation of risk assessments, pre startup safety reviews, and document & quality control. • Managed the planning and execution of turnaround projects which including supervising mechanical joint integrity checks as part of pre startup quality assurance.

London, England, Gb

Managed the design & execution of produced water handling & infrastructure capital projects ($3-5mln)• Provided forecasts, models and analysis to support need for $5mln capital expenditure in order to maintain approx $10mln in annual revenue; created tool to track and forecast production volumes vs. capacity • Designed and managed the construction of 8.5mile high pressure water collection/discharge pipeline including first implementation of HDPE pipe; developed basis of design, construction work packages, project timelines • Formulated budget by generating cost estimates; controlled spending by tracking actual spend vs. estimates • Negotiated procurement of materials and equipment with 3rd party suppliers, negotiated service agreements with 3rd party engineering & construction contractors, and negotiated land agreements with private entities• Managed the construction & on time delivery of produced water offloading and injection facilities; delivery came in under budget by approx $415k (12%); commissioned startup and authored operating procedures for facility.

Combined Cycle-Cogeneration Power Plant Performed optimization system testing in which plant historical data is analyzed in order to correct and deploy SmartProcess Economic Optimizer program; -Developed the Utilities Record Integration GIS user’s manual; -Optimized shift schedules and submitted funding proposals

Performed optimization system testing in which plant historical data is analyzed in order to correct and deploy SmartProcess Economic Optimizer program;Developed the Utilities Record Integration GIS user's manual; Optimized shift schedules and submitted funding proposals; Updated plant layout, facility flow charts and drafted proposed feed load-out design using AutoCAD Condition Monitoring of facility equipment e.g., motor bearings with the use of thermographic analysis.Proposed and implemented magnet equipment for decontamination & wheat cleansing process.

M.S., Mechanical Engineering

B.S., Mechanical Engineering