Uthaya Kumar Thayalan Email & Phone Number

Butterworth, My

Penang, Malaysia

To prepare for product change over following daily production schedule.- Monitoring of yield and reject rates of machine and perform corrective action/troubleshoot machine.- To escalate and To take decision on machine stop die to process/product/machine errors and prepare engineering report to management- To prepare Daily report on product yield, output, abnormalities and follow ups. - Attend meeting on Every shift beginning- Update Dept Head, Manager on machine status on every start/end of shift- Prepare Shutdown sequence for Company Shutdown- Train mfg technicians for basic troubleshooting skills/product handling- To Prepare SOP For new process/machines- Perform PM Following SOP- Monitoring of Spare Part inventory- Major & minor troubleshooting on all equipment - New Machine installation and pilot run for qualifications

Butterworth, Penang, Malaysia

- To arrange transport services to schools and tours inbound- To ensure all vehicles in top condition- To ensure all vehicles to go thru Puspakom inspection by due date- To assign drivers/ routes for the journey

Bayan Lepas, Penang, Malaysia

Prepare and publish shiftly machine downtime reports-Ensure line and machine readiness prior to release line to production-Provide corrective action to minimize rework/defect quantity-Provide improvement ideas to reduce high downtime-Machine calibration for every conversion-Program editing and set-up new programs-Monitoring yield for Post IR on hourly basis-New line set-up and machine floor lay-out-Hourly monitoring for machine throw out rate and trouble shoot defects- Machine troubleshooting and modification according to product readiness. - To provide immediate correctove action /decision on any issue arised during priduction running

Perai, Penang, Malaysia

Line owner for IBM/Lucent products-To ensure 5s of the line and work place-To ensure Kanban system practiced-Download and upload machine throw our report to server-Monitoring of machine utilization and error rate counts-Update daily conversion check list-Monitoring of first 5 boards without any defects for every cascade change over prior to release line to production-Monitoring yield for Post IR on hourly basis-Shiftly monitoring for yield at 5DX & ICT-Monitor line backlog at PPS(Pack Plan Sequence)-Monitoring for machine throw out rate and provide CA to minimize fallout rate-Machine and line conversion-Conversion of tools/nozzles on machines according to product-To Ensure Parameters following SIC(Stand instruction card) for every product conversion-Part verification and device update for new parts-Perform Nozzle centering and change EOL parts- Program editing for PCB Boards-Support production for rework and part verification through Fuji Flexa Director system-Verify parts vs. graphic list vs. part data for replenished parts and different supplier-Trouble shooting for machines system-Support NPI model running-New line set-up and machine floor lay-out.Machines Handled CP – Model FUJI CP-65:Chip Placement Machine with capability of holding 140 feeders/parts at one time. DEK–Model 265-GSX:Solder printing machine for PCB boardsGSM11 - Model Universal GSM II -4688A :Chip placement machine using nozzle with air pressure to pick parts from feeders and place on BoardHeller Reflow Oven

Ipoh, Perak, Malaysia

-Responsible for overall new product introduction factory system set up -resolving technical issues that will hinder smooth flow of lots, in production -To publish & gett disposition from low yielding lot <24hrs. -To ensure execution of Wafer Qual Systems. SBR run–verify components as on Physical vs Agile BOM page-Special instructions and requirements -Planning and execution with production to run SBR(special build requests) & WQ (wafer qualification)Daily routine tasks-Brief production team on new implementation/changes on Build diagram, process changes and component changes-Provide disposition for machine error on device to minimize yield drop-Monitoring and maintain high yield without major scraps.-To buy-off D/A, wire bond configuration prior to allow SBR lots to be proceed which release to production build-To provide wafer mapping CSV to Fremont on Wafer qualification-To solve production issues related to IT, component @receiving dept/ component @IQA and SCM on Job planning-To verify Physical vs. Assy Drawing in case of mixed up componentsSBR is a build that requested by customers and to collect data by using unqualified materials. -Change parameters at some workstations to reach target required.-Buy-off die placement,tolerance as per spec/To do Herm city test for Wire pull, Shear materialsWQ-Wafer Qualification Build -A build where LD will qualified and later released to production usage -Test on this builds are dark current test, BI, OBI, HT and Room Temp Test to ensure Wafer that used is qualified.- To provide product improvement.- Monitoring off all materials and ensure unqualified materials has been passed test/qualified all tests.- Ensure Bom page and Agile CM page is up-to-date to avoid misuse of components- To ensure all Wafer Qualify reports up dated and sent to Fremont team- To lead overall shift in planning/material/production/ tracking/and reports.

Bayan Lepas, Penang, Malaysia

Joining Class 10 cleanroom as Manufacturing Technician1.Troubleshoot the conveyor and sensor fault on the dipper machine. 2.Perform bath change(15000 cycle count) and increase the chemical level for new set-up and product. 3.Troubleshoot and verify the alignment for lane lifter and cassette crash. 4.Perform VI inspection and BLR reading before release the machine to production. 5.Troubleshoot the spindle,lifter and gripper for Centaur and Unicorn machine 6.Verify the teach point and calibrate load cell for pad arm. 7.Perform evaluation to assist the Engineer on new product implementation that been developed to match WD requirement standard, suggest the improvement that need to be done to the product. 8.Verify and take corrective action on the SPC data if it fails the target spec given by customer.9. Chemical Handling: To withdraw N2, and other chemicals for machine usage10. To follow WI to run production materials and ensure all within required specs.

Ipoh, Perak, Malaysia

Joining under maintenance team as technician, job task includes-attending daily meeting and update issues/recoveries/electricity n waterUsage level. -update and stock keeping inventory for maintenance usage items-prepare tasks/projects and arrange shift for technicians.-provide audio visualization set-up- Mixer yamaha 40channels, lighting setup, for all events such as wedding dinner/product launching/Annual General Meeting/charity events.-attend in house customer complaint on maintenance issues- Servicing and maintenance of AHU(Air Handling Unit) -Servicing and maintenance of cooling tower -Servicing and maintenance of CWP-chill Water Pump-Servicing and maintenance of water pumps, room electrical items-To ensure all lighting and electrical items internal and external of premise in working condition-To ensure lightings and corridor AHU on/off according to schedule-To prepare shiftly reports and hand over to manager during meeting-To ensure emergency Gen Set is ready condition ( fuel, lubricant) and test run intermediately