ADNOC offshore/LNG Preparation and Review of all documentation including, design documents, installation documents, commissioning reports, procurement, and invoicing. Review contractor's procedures for the application and installation of protective coatings and cathodic protection systems. Routine Monitoring and Maintenance Activities for Transmission Pipelines, Plant Piping, Vessels, AST Bottom, Tank Internal, Jetties, and Sea Water Intake System. Perform testing, evaluation, and installation of cathodic protection systems to inhibit corrosion on various structures. Conduct all cathodic protection related monitoring, surveys, and inspection  Installation and testing of suspended MMO Anode at Tank Internal CP system in Fire water storage tanks. Installation and testing of Magnesium Sacrificial Anode for fire water supply lines. Inspection on anode installations in Offshore Piers, Onshore Refineries and Pipelines for galvanic and ICCP types as per NACE and company approved standard practices Installations and testing for sacrificial Aluminum Anodes at Vessel Internal CP system in Low Sulphur fuel water slurry separators, Tanks, etc. Installation and testing of Magnesium Sacrificial Anode for fire water supply lines. Pre-Design Site Survey (Soil resistively data, Existing CP systems data collection, service data collection and CP equipment’s locations) DC & AC Interference study  CIPS & DCVG Survey CP Revamp activities (Tank bottom plate replacement, deep well ground re-location,) Provide regular reports and presentations on status and future for CP systems.

Responsible for the implementation of quality control and assurance system in accordance with project specification and engineering standardsPrepare a Project Quality Plan, Quality Control Procedure and ITP.Verify the equipment and devices used in the project meet the required specification as per project requirements, company standards and tested in accordance with international proceduresWitnessed Inspection for installation of 11/33/415kV transformers, LV/ HV Switchgear's, Panels and motors. Inspection of electrical panel installation, monitoring cable routing, cable tray installation, control panel wiring and termination activitiesInstallations and High Voltage testing of 11kV cable terminations, Splicing.Inspection on transformer installation, cable termination and torque testingInspection of LV, MV switchgear, MCC (480V, 4.16KV, 13.8KV) installation, CT, PT, protection & management relay testing, Breaker testing and Point to Point testInspection on relaying control panel installation and termination, loop test and functional testInspection on cathodic protection system installations for process equipment and pipelines and tanks.Inspection on anode installations in Offshore Piers, Onshore Refineries and Pipelines for galvanic and ICCP types as per NACE and company approved standard practices. Installations in concrete structures and carry out inspections in accordance with NACE Recommended practices.Installations and testing for sacrificial Aluminum Anodes at Vessel Internal CP system in Low Sulphur fuel water slurry separators, Tanks, etc.480V, 3.3kV,4.16KV,13.8KV and 34.5KV Switch gears and MCC (usingSF6, Vacuum Circuit Breakers, Air Circuit Breaker) start-up and commissioning(ABB, Siemens, GE).4.16KV/480V, 34.5/4.16KV, 34.5/13.8KV, 13.8/4.16KV,11/3.45kV and Dry type Transformers pre-commissioning and commissioning (ABB, Siemens, volt amp).

• Participate in SAT (Site Acceptance Test) with vendor premises.• Verify all required inspection report and test records are systematically generated and compiled according to the approved QC Procedures.• Responsible for maintaining all Quality Records of Inspection, incorporate Relines and Closing NCR’s.• Responsible for Preparing of Final Quality Dossier Over Project Competition.• Responsible for Preparing Test Reports upon Inspection Competition.• Participation with client and sub vendors for developing engineering document as per the project requirement.• Monitoring to subcontractor and conducting inspection with client on daily basis• Monitor and surveillance for line differential protection relay function test, interlock and inter trip test, automatic transfer test and line stability test.• Monitor and surveillance the motors installation, per commissioning and Involve motor solo run testing, on load& full load test.• Scheduling and carrying out the field inspections and get it approved by Client.

• Witnessed Inspection for Supports, Cable Trays, and Instruments Installation.• Witnessed Site Inspection for Installation of F&G and PA/GA Instruments like Detectors, Horn, and beacons.• Witnessed Inspection for Fiber Optic Splicing and OTDR Test.• Witnessed Installation inspection for Well head RTU’s.• Witnessed Instrument Calibration of process variable instruments.• Witnessed Panel Installation, Consoles and Computers and printer Installation.• Witnessed Inspection for installation of 11/33/415kV transformers, LV/ HV Switchgear's, Panels and motors.• Inspection of various electrical construction activities like switchgear installation, Transformer installation, Battery Banks, cable tray installation & cable laying & Termination.• Endorse documentation received from contractor (material specification, method statements, Inspection and Test Plans, drawings, test results, other technical documentation, etc.) for implementation and compliance.• Endorse documentation received from contractor (material specification, method statements, Inspection and Test Plans, drawings, test results, other technical documentation, etc.) for implementation and compliance;

• Preparation and Submittal for RFI.• Verify the equipment and devices used in the project meets the required specifications per project requirements, Standard and tested in accordance with the procedures.• Installation of control panel marshalling panels and termination continuity and Meggar test .Insulation Resistance and Winding Resistance Testing of LV, MV motors.• Records Routine area Surveillance for Instrument project Scope.• Records Routine area Surveillance for Instrument project Scope.• Ensure that all works are carried out as per the approved method statements and drawings.• Assist the QA/QC senior engineers in preparation of the final handing over documents, testing and commissioning reports etc.• Prepare Technical Record and documentation.• Conducting the inspections for equipment’s grounding, earth rod installation, lightning conductors installations and exothermic welding for the joints.• Conducting the inspections of cable trench, UG cable laying, cable splicing/jointing as per the specs/method statements.