Victor P Email & Phone Number

Foster City, California, Us

Foster City, California, Us

Foster City, California, Us

Foster City, California, Us

• Discrepancies between theoretical and actual materials have been found during assembly testing, therefore all materials used on the vehicle were internally tested.• NDT and Analysis on the component prior to destructive testing and correlating the results, thereby identification of the source of failure.• Identified problems with exciting Materials coupon testing and suggested a new method for accurate results.• Guiding and supporting CAE and Safety Engineers with various Materials Testing.• Minor activities include but are not limited to Metallurgical sample preparation, coupons cutting, milling, and drilling.• Researching the market and identifying cheaper tools to prepare mass coupons for various destructive testing.• Introduced 5S practices and created a safe work environment, while developing Lab capabilities.• Managing laboratory inventory, ordering supplies, maintaining calibration records, fabricating fixtures in-house.

Dayton, Oh, Us

• Enhancing the raw wood strength equivalent to structural aluminum by thermochemical treatment followed by mechanical compression.• Deigned a Uniaxial compression die using Solidworks for fabrication of densified wood.• Sample Preparations for Materials Characterization Techniques: Powder & Thin film X-Ray Diffraction (XRD),Scanning Electron Microscope (FE-SEM) and X-ray Photoelectron Spectroscopy (XPS).• Identification of Crystallite Size and Crystallinity Index using data from Rigaku Wide-Angle XRD by Deconvolution and curve fitting using Origin Pro Software.• Microstructure evaluation before and after chemical treatment using Field Emission – Scanning Electron Microscope (SEM).• Understanding the interaction between Carbon bonds, Quantifying elements using XPS, and curve-fitting software CASA XPS.• Investigation & Optimizing has led to an increase in the strength of the densified woods equivalent to structural aluminum and 5.5-fold time higher strength than raw wood.

Dayton, Oh, Us

• Aspects of this job involve data acquisition of test samples for Environmental Protection Agencies (EPA), Cincinnati, Ohio.• Data acquisition of XPS and XRD measurements on powder and thin film Absorbent materials according to EPA requirements.• Training Students to use various Materials Testing and Characterization Equipment.• INSTRON Universal Tensile Test & Compression Testing, BUEHLER’s Rockwell Hardness Test, Fatigue test, Sample Preparation, Field-Emission Scanning Electron Microscopes (SEM) Rigaku’s Wide Angle and Small Angle X-Ray Diffraction (XRD) and Kratos Analytical XPS.• Managing Students Data using MS Excel and analyzing individual performance periodically.• Concerning the circumstance for understanding students’ needs and develop strategies forcontinuous improvement of the individual.• Presenting the collected data to the Advisor and discussing the development of Student Activity.

Dayton, Oh, Us

The Materials Science and Engineering Society (MSES) is the student organization at Wright State University for all things materials science-related. The main purpose of MSES is to promote the self-seeking will and confidence to pursue all fields related to Materials Engineering including metallurgy, ceramics, and polymers. MSES promotes materials science and engineering through routine industry tours and conference visits off campus while providing peer advising and other student resources on campus.

Chennai, Tamil Nadu, In

• Developed a Semi-synthetic Polymer composite at a low cost with uncompromised strength to replace Kevlar-29.• Functions involve Material & Fabrication method selection, Selection of Epoxy as binders, and different fiber orientation. • Materials used – Jute Natural Polymer and Kevlar 29, a Synthetic Polymer. • Performed Compression Testing, Impact Testing, and 3 Point Bend Test following ASTM standards.• Varying fiber orientation and improving processing had led to 37% increased strength compared to pure Kevlar 29.

Chennai, Tamil Nadu, In

• Developing Metal Matrix Composite samples using Stir Casting with Aluminum 6061, Aluminum oxide & Silicon carbide.• Optimizing Stirring speed, cooling rate based on Literature review and performing experimentally.• The investigation had led to the Achievement of Optimizing process in the fabrication of Metal Matrix Composites.

Master Of Science - Ms, Material Science & Engineering

Bachelor'S Degree, Mechanical Engineering

School Graduate, Mathematics And Computer Science

Senior Professional, First Aid