 About Mechanical : • Site surveillance for the work carried out are as per approved ITP , Procedures , Specification and Drawing . • Conduct external and internal visual inspection for pressure vessel .• Prepare documents to receive goods .• Read carefully ITP , Specification and Method Statement before working. • Strictly implementation of preservation activities at site and at material storage• Prepare the drawing for acceptance and construction . • Sending… Show more  About Mechanical : • Site surveillance for the work carried out are as per approved ITP , Procedures , Specification and Drawing . • Conduct external and internal visual inspection for pressure vessel .• Prepare documents to receive goods .• Read carefully ITP , Specification and Method Statement before working. • Strictly implementation of preservation activities at site and at material storage• Prepare the drawing for acceptance and construction . • Sending NFI (Notify for Inspection ) to contractors and clients (Coordinate with them for acceptance).• Equipment Installation Alignment and Elevation Survey for Vertical and Horizontal vessels.• Having technical experience in Static and Rotary Equipment ( Pump ,Air cooler heat exchanger ,Centrifugal …. ) o Pump : Shaft alighment ( preliminary and final ) • Have the knowledge about API 686 RP • Shaft Alignment of rotating equipment’s such as pumps, Compressors, gear box, turbine, etc including Soft foot check and DBSE. • Attending weekly log book entry and NCR meeting with client and field engineering .• Review of final inspections reports.  ABOUT PIPING : OFFICE WORK : • Prepare ITP , WPS , Specification , Procedure and related QA/QC document .• Guidance Sub-contractor prepare documentation .• Mornitoring inspection logsheet update submit by sub-contractor .• Review hydrotest package . SITE WORK : • Witness Welder qualification and review certificate welder . • Material receiving inspection . • Monitoring piping and support fabrication at workshop and field .• Monitoring and check dimension , fit up , before -during and after welding .• Monitor NDE status , repair rate , Interpretation RT film . • Flushing inspection . • Line check before hydrotest .• Witness hydrotest / Pneumatic test . • Re-instatement inspection . • Bolt tightening inspection . • Close punchlist as required . • Walk through final inspection . • Close final punch-list . Show less

QA/QC ENGINEER ( PIPING & MECHANICAL ) in PTSC for SAO VANG DAI NGUYET PROJECT. ( MAIN WORK IN TOPSIDE ) ( Short term Job )  About Mechanical : • Ensure Quality Control activities at site are performed in accordance with relevant QCP,ITP,MS. .• Review of material diposition reports for the equipment’s arrived on the site .• Strictly implementing the approved ITP . • Confirm for any deviation with in the Standards and specification prior to issuing RFI to the… Show more QA/QC ENGINEER ( PIPING & MECHANICAL ) in PTSC for SAO VANG DAI NGUYET PROJECT. ( MAIN WORK IN TOPSIDE ) ( Short term Job )  About Mechanical : • Ensure Quality Control activities at site are performed in accordance with relevant QCP,ITP,MS. .• Review of material diposition reports for the equipment’s arrived on the site .• Strictly implementing the approved ITP . • Confirm for any deviation with in the Standards and specification prior to issuing RFI to the client.• Equipment Installation Alignment and Elevation Survey for Vertical and Horizontal vessels.• Inspection for Installation of ladders, platforms and other Structural attachments.• Inspection for Internal component Installations of equipment’s .• Shaft Alignment of rotating equipment’s such as pumps, Compressors, etc including Soft foot check and DBSE.• Verify the parallelism on suction / discharge piping connection if stress free condition. • Having technical experience in Static and Rotary Equipment ( Pump ,Air cooler heat exchanger ,Centrifugal …. ) o Pump : Shaft alighment ( preliminary and final ) • Have the knowledge about API 686 RP • Review of final inspections reports. About Piping :• Prepare ITP , WPS , Specification , Procedure and related QA/QC document . • Running welding procedure for piping follow with MTO , SPECIFICATION FOR WELDING OF PROJECT AND CODE ( ASME IX , ASME B31.3 ) .• Mornitoring inspection logsheet update submit by sub-contractor . • Review hydrotest package . • Witness Welder qualification and review certificate welder . • Material receiving inspection . • Monitoring and check dimension , fit up , before -during and after welding .• Monitor NDE status , repair rate . • Flushing inspection . • Line check before hydrotest .• Witness hydrotest / Pneumatic test . • Re-instatement inspection . • Bolt tightening inspection . • Close punchlist as required . • Walk through final inspection . • Close final punch-list . Show less

 About Installation and Welding : • Conducting qualification test for welders (WQT) with third party inspector (WQT conducted based on approved WPS and ASME sec- IX & AWS D1.1 )• Preparing weld maps and identification of weld joints as per isometric drawing • Verifying baking , holding and electrode issuance records• Maintaining log book for daily activities and updating RFI status • Regarding monitoring and reviewing of calibrated equipment and maintain records… Show more  About Installation and Welding : • Conducting qualification test for welders (WQT) with third party inspector (WQT conducted based on approved WPS and ASME sec- IX & AWS D1.1 )• Preparing weld maps and identification of weld joints as per isometric drawing • Verifying baking , holding and electrode issuance records• Maintaining log book for daily activities and updating RFI status • Regarding monitoring and reviewing of calibrated equipment and maintain records • Conduct tool box meeting for welders and welding foreman • Preheat , interpass temperature and heat input checking as per approved WPS • Good knowledge in material of cacbon steel , stainless steel , alloy steel • Inspection of joints and its details based on isometric drawing , WPS and welders before starting • Inspection and clearence of fit up weld as per the approved WPS AND CHECK DIMENSION BEFORE WELDING FOLLOW WITH IFC DRAWING AND SPECIFICATION OF PROJECT .• After welding , inspect weld visual , DIMENSION ( AFTER WELDING ) and offer NDT • Prepare of daily welding report and maintain quality records• Updating daily NDT repair status and take preventive action • Coordinating with client for inspection activities • Maintain all inspection report and NDT reports .  About Painting : • Check painting material certificates and painting materials .• Check surface preparation . • Check and record atmospheric conditions prior to starting of painting operations .• Verify the correct color coding and paintings . • Check visual , measuring dry fim thickness of coating . • Prepare painting inspection report • Monitoring during painting application to ensure all comply with approved procedures• Understanding the inspection test plan ( ITP ) , and The specifications / requirements of customer . Show less

 About Welding• Conducting qualification test for welders (WQT) with third party inspector (WQT conducted based on approved WPS and ASME sec- IX & AWS D1.1 )• Preparing weld maps and identification of weld joints as per isometric drawing • Verifying baking , holding and electrode issuance records• Maintaining log book for daily activities and updating RFI status • Regarding monitoring and reviewing of calibrated equipment and maintain records • Conduct tool box… Show more  About Welding• Conducting qualification test for welders (WQT) with third party inspector (WQT conducted based on approved WPS and ASME sec- IX & AWS D1.1 )• Preparing weld maps and identification of weld joints as per isometric drawing • Verifying baking , holding and electrode issuance records• Maintaining log book for daily activities and updating RFI status • Regarding monitoring and reviewing of calibrated equipment and maintain records • Conduct tool box meeting for welders and welding foreman • Preheat , interpass temperature and heat input checking as per approved WPS • Good knowledge in material of cacbon steel , stainless steel , alloy steel • Inspection of joints and its details based on isometric drawing , WPS and welders before starting • Inspection and clearence of fit up weld as per the approved WPS • After welding , inspect weld visual and offer NDT • Prepare of daily welding report and maintain quality records• Updating daily NDT repair status and take preventive action • Coordinating with client for inspection activities • Maintain all inspection report and NDT reports . Show less

 About Mechanical : • Ensure Quality Control activities at site are performed in accordance with relevant QCP,ITP,MS. .• Strictly implementation of preservation activities at site and at material storage .• Confirm for any deviation with in the Standards and specification prior to issuing RFI to the client.• Equipment Pre Installation Inspection.• Equipment Installation Alignment and Elevation Survey for Vertical and Horizontal vessels.• Shaft Alignment of rotating… Show more  About Mechanical : • Ensure Quality Control activities at site are performed in accordance with relevant QCP,ITP,MS. .• Strictly implementation of preservation activities at site and at material storage .• Confirm for any deviation with in the Standards and specification prior to issuing RFI to the client.• Equipment Pre Installation Inspection.• Equipment Installation Alignment and Elevation Survey for Vertical and Horizontal vessels.• Shaft Alignment of rotating equipment’s such as pumps, including Soft foot check and DBSE.• Verify the parallelism on suction / discharge piping connection if stress free condition. • Having technical experience in Static and Rotary Equipment ( Pump ,Air cooler heat exchanger ,Centrifugal …. ) o Pump : Shaft alighment ( preliminary and final ) • Have the knowledge about API 610 , API 686 RP • Review of final inspections reports.• Preparation of Punch list after Site walk through with the client and verification of punch list completion. About Piping : • Inspect and make the report for each Inspection and Testing plan (ITP).• Running welding procedure for piping follow with MTO , SPECIFICATION FOR WELDING OF PROJECT AND CODE ( ASME IX , ASME B31.3 ) .• Conducting qualification test for welders (WQT) with third party inspector (WQT conducted based on approved WPS and ASME sec- IX )• Make fit-up inspection, quality control before welding and make visual inspection after welding . • Follow up and update NDT status and inform construction team once having NDT result . • Create a control file to observe work daily . • Have the knowledge about ASME 31.3 , ASME IX • Ensuring the welding machines , ovens and tools calibration is valid and working properly • Inspection of line check as per P&ID /ISO drawings and to raise the punches • Preparation of hydro test package and getting approval from client . • Raising RFI for notification to client for daily welding and piping activities as per ITP Show less

 About Mechanical : • Prepare documents to receive goods at Zone 1 port ( NSRP).• Read carefully ITP and Method Statement before working. • Prepare the drawing for acceptance and construction . • Sending NFI (Notify for Inspection ) to contractors and clients • Equipment Installation Alignment for Vertical and Horizontal vessels.• Inspection for Installation of ladders, platforms and other Structural .• Inspection for Internal component Installations of… Show more  About Mechanical : • Prepare documents to receive goods at Zone 1 port ( NSRP).• Read carefully ITP and Method Statement before working. • Prepare the drawing for acceptance and construction . • Sending NFI (Notify for Inspection ) to contractors and clients • Equipment Installation Alignment for Vertical and Horizontal vessels.• Inspection for Installation of ladders, platforms and other Structural .• Inspection for Internal component Installations of equipment’s .• Shaft Alignment of rotating equipment’s such as pumps, , etc including Soft foot check and DBSE.• Verify the parallelism on suction / discharge piping connection if stress free condition. • Inspection for the Installation of Air coolers.• Having technical experience in Static and Rotary Equipment ( Pump ,Air cooler heat exchanger ,Centrifugal ) o Pump : Shaft alighment ( preliminary and final ) • Have the knowledge about API 686 RP  About Piping : • Running welding procedure for piping follow with MTO , SPECIFICATION FOR WELDING OF PROJECT AND CODE ( ASME IX ) .• Conducting qualification test for welders (WQT) with third party inspector (WQT conducted based on approved WPS and ASME sec- IX ) • Make fit-up inspection, quality control before welding and make visual inspection after welding . • Follow up and update NDT status and inform construction team once having NDT result . • Create a control file to observe work daily . • Have the knowledge about ASME 31.3 , ASME IX • Inspection of line check as per P&ID /ISO drawings and to raise the punches • Preparation of hydro test package and getting approval from client . • Flushing inspection . • Line check before hydrotest .• Witness hydrotest / Pneumatic test . • Re-instatement inspection . • Bolt tightening inspection . • Close punchlist as required . • Walk through final inspection . • Maintain all inspection reports and NDT reports • Ensure the spools coated and complies with the quality requirements . Show less

: PIPING SUPERVISOR ( GRP PIPE ) in UGPX package at Nghi Son Refinery and petrochemical• Inspect and make the report for each Inspection and Testing plan (ITP). Make sure that the quality aspects of all construction activities such as material inspection, cutting, fitting, dimension survey, etc …. have to be complied with the approved project procedures.• Make fit-up inspection, quality control before bonding and make visual inspection after bonding . • Create a control file to… Show more : PIPING SUPERVISOR ( GRP PIPE ) in UGPX package at Nghi Son Refinery and petrochemical• Inspect and make the report for each Inspection and Testing plan (ITP). Make sure that the quality aspects of all construction activities such as material inspection, cutting, fitting, dimension survey, etc …. have to be complied with the approved project procedures.• Make fit-up inspection, quality control before bonding and make visual inspection after bonding . • Create a control file to observe work daily . Show less