· Participate in Daily OME meetings and discuss the daily routine activities, · Daily routine parameters checking by using PI system and do optimization if required, · Issue Trip or Trouble report against any Trouble at plant, · Investigate the trip report from process point of view and provide recommendations for rectification, · Prepare conceptual design for new modification, · Issue Management of change (MOC) for any modification, · Issue Engineering work Request (EWR) for detail design belongs to MOC, · Review the design packages prepared by design section (CAPEX,OPEX), · Establish Standard operating procedure (SOP) constituting all possible scenario, · Establish critical operating procedure (COP) constituting all possible scenario for critical parameters, · Establish Emergency Shedding plan to counter emergency situation, · Member of JSA, PSSR, Risk assessment, Deviation form. · Conduct kick off meeting with contractors/vendors, · Finalize the scope of work for contractors and consultants. · Prepare datasheets for equipments, · Conduct emergency conversation by observing daily parameters · Manage documents such as P&IDs, PFDs, MSDs, HMB, UFDs, LDT, SIS data sheets from EDMS,  · Prepare hydraulics for line sizing and pumps selection purpose, · Prepare simulation for pant to observe changes on parameters by changing specific parameters, · Conduct HAZOP and SIL to analyze the  changes affect on plat parameters, · Manage material stock which should be available during T&I or shutdown, Areas:1. Steam Generation 3 boilers HP 150 ton & 49 bar, MP 110 ton & 20 bar, LP 100 ton & 6.5 bar,2. Compressors 3 Comp 12000 m3/hr at 8 bar3. De-min water system 3 mixed bed 54 m3/hr at 5bar4. Sea water intake 10 Pumps 35000 m3/hr at 6 bar5. Fire water system 8 Pumps 4600 m3/hr at 13.5 Bar6. Potable water system 6 Pumps 1000 m3/hr at 7 bar7- About 100 tanks and related pump houses.

· Participate in Daily OME meetings and discuss the daily routine activities, · Daily routine parameters checking by using PI system and do optimization if required, · Issue Trip or Trouble report against any Trouble at plant, · Investigate the trip report from process point of view and provide recommendations for rectification, · Prepare conceptual design for new modification, · Issue Management of change (MOC) for any modification, · Issue Engineering work Request (EWR) for detail design belongs to MOC, · Review the design packages prepared by design section (CAPEX,OPEX), · Establish Standard operating procedure (SOP) constituting all possible scenario, · Establish critical operating procedure (COP) constituting all possible scenario for critical parameters, · Establish Emergency Shedding plan to counter emergency situation, · Member of JSA, PSSR, Risk assessment, Deviation form. · Conduct kick off meeting with contractors/vendors, · Finalize the scope of work for contractors and consultants. · Prepare datasheets for equipments, · Conduct emergency conversation by observing daily parameters · Manage documents such as P&IDs, PFDs, MSDs, HMB, UFDs, LDT, SIS data sheets from EDMS,  · Prepare hydraulics for line sizing and pumps selection purpose, · Prepare simulation for pant to observe changes on parameters by changing specific parameters, · Conduct HAZOP and SIL to analyze the  changes affect on plat parameters, · Manage material stock which should be available during T&I or shutdown, Areas:1. Steam Generation 3 boilers HP 150 ton & 49 bar, MP 110 ton & 20 bar, LP 100 ton & 6.5 bar,2. Compressors 3 Comp 12000 m3/hr at 8 bar3. De-min water system 3 mixed bed 54 m3/hr at 5bar4. Sea water intake 10 Pumps 35000 m3/hr at 6 bar5. Fire water system 8 Pumps 4600 m3/hr at 13.5 Bar6. Potable water system 6 Pumps 1000 m3/hr at 7 bar7- About 100 tanks and related pump houses.

Detail Engineering for Jizzan Refinery being commissioned in Jizzan,Saudi Arabia, including,1- Amine Regeneration unit2- Fuel Gas sweetening Unit3- Fuel gas Distribution System4- Sour water treatment Unit· Detail design of available FEED package for Sour Water Strip unit, Amine Recovery Unit, Gas sweeting Unit and Gas Distribution Unit. · Prepare developing stage packages, 30%, 60%, 90% and IFC. · Review and evaluate 3D model and conduct HAZOP study. · Receive comments from ARAMCO for each submitted unit. · Reply the comments with solid justification and calculations for closure. · Conduct HAZOP and SIL for each submitted package.· Prepare process & instrument diagrams, process flow diagrams, material selection diagrams, Sketches, utility flow diagrams, line designation  table , process description, control narrative, scope of work, pressure relief valves Data sheets, control valve data sheet, SIS sheets. · Coordination with other EPC companies about any modification and take appropriate action against any change. · Vendor selection for different actives such as to conduct Risk based inspection study, · Performed technical and commercial proposals evaluation. · To conduct hydraulics for pump sizing and line size calculation. · To perform calculation to find out the utilities demand · Develop simulation for all the units of project, find out any change in parameters and perform corrective action against the result. · Software used for detail design activities, COREWORX, HYSYS, PEROS, Fisher, SRVS6.2, Auto CAD, Mircostation, SPPID, MS office, etc. · Deal with other EPCs on conflicted action items by using COREWORX, · Conduct kick of meetings, minutes of meetings, Projects review meetings with ARAMCO and Vendors etc.

Process Engineer: Certified from Khafji Joint operation / ARAMCO (onshore/offshore) Job responsibilities:• Prepare scope of work, Site survey for location verification• Conduct KOMs, MOMs, Projects Review meetings with client, Meetings with Vendors etc • To prepare proposal with economical man-hours estimation.• To prepare DBSP, Data Sheets, HAZOP study, PZVs & PCVs sizing etc.• Update and prepare PFD’s, P&ID’s, Sketches, UFD’s, MTO and LDT’s, etc.• To prepare simulation in HYSYS, Equipment sizing, Piping Hydraulics and line sizing, • Software used, HYSYS, Auto CAD, Micro Station, SP P&ID, Fisher, SRVS6.2, MS office, etcPROJECTS HANDLED:1. Feasibility Report for Upgrading of Oily water treatment facilities, ARAMCO/KJO,Khafji2. DBSP for Upgrading of Oily water treatment facilities, ARAMCO/KJO,Khafji6. Natural Gas plant bypass line installation, ARAMCO/KJO, Khafji7. Compressor with related accessories Replacement with new one, ARAMCO/KJO, Khafji8. Concrete pipe line replacement by RTR line, ARAMCO/KJO,Khafji9. Carbon steel line replacement by stainless steel, United, SABIC, Jubail10. Level interface control up gradation, ARAMCO/KJO, Khafji.11. Gas metering Station ARAMCO / HADEED SABIC, Jubail12. Rectification of Butane and Ethan facilities ARAMCO/YNGL Yanbu

Unit production is 200MTPD, 32% Caustic produced by Asahi Kasei electrolysis membrane cells and converted to 50% Caustic by Multi effect evaporator. 200MT 35% HCl is produced by Furnaces. Job Responsibilities:• Handle unit for smooth production.• Update and prepare PFD’s, P&ID’s, UFD’s, MTO and LDT’s, etc• To prepare maintenance and shutdown jobs schedule and implement it.• Material balance for caustic plant at different flow rates for Brine preparation, Brine Treatment, Caustic Production, H2 Production and Cl2 Production.• Material balance for acidic effluent treatment plant.• Reverse osmosis plant smooth operation. • New cooling water pipe line HydraulicsAlong with this to handle and look after the utilities such as• Cooling towers, Absorption chillers, Reverse osmosis, Demi water plant, Compressors.

My job as a Shift Engineer was to operate the equipments, perform the daily routine maintenance, perform shut down maintenance, coordinator with project team, replacement of the faulty equipments, man power management, equipments related record logging, to raise work order against any abnormality, to check the equipment’s related readings, survey the work area, etc.• HVAC, Air Handling Units, 10 units, Total Capacity 3000 RT / hr,• Compressors, Screw compressors, 15 in numbers,1176 m3/hr each, 8 bar, Double Acting Reciprocating, 04 in numbers, 580 m3/hr each, 18 bar, Centrifugal 3 Stage, 04 in numbers, 6000 m3/hr each, 8 bar,• Chillers, Absorption Chiller, 02 in numbers, 800 RT each, Vapor compression Chillers, 06 in numbers, 400 RT each,• Cooling towers, Counter & cross,15 in numbers, 400 m3/hr & 600 RT each• Boilers, Fire tube & WHRB, 08 in numbers, steam 26 bar, 30 Ton/hr• De-Min Water plant, R.O based and Ion exchange, 5 m3/hr,• Miscellaneous, Nitrogen plant, Water turbines, Water filters, Compressed Air dryers & filters,

My core responsibilities were to look after the process for the production 5MT of dry GELATINE from organic constituents obtained from crushed bones. Process based on multi effect evaporators to produces 32% Gelatine and then Tunnel dryer used to dry up Gelatine up to 98 % and after that that dry product crushed down to make powder product.

Joined as internee for one month and studied the following units.UREA,AMMONIA,CAN,NP,