1) searching for Russian suppliers, instead of foreign suppliers, that technically can manufacture assembly units and components for gas turbine unit, supplied by LLC "Russian Gas Turbines"2) development, review, assessment and coordination of technical part of supplier quotations (technical/commercial proposals)3) performing of pre-assessment of potential suppliers regarding their capabilities4) performing of QMS (Quality Management System) and EHS (Environmental, Health and Safety) audits of potential suppliers for conformance to the requirements of ISO 9001 and to the requirements of LLC "RGT".Making audit reports and work with the supplier for eliminating detected non-conformities during audit.5) performing supplier qualification and control of performing qualification plan in time.6) during serial production of qualified assembly units and components - performing quality control of the products, supplied to LLC "RGT" from qualified suppliers, by performing quality analysis and performing audits and/or implementation of corrective actions7) development of internal procedures in LLC "RGT"I am responsible for electrical products and in our Sourcing Quality Department I am responsible for coordination the work regarding developing and updating QMS procedures, KPIs of our department and our suppliers, planning supplier audits.Achievements:• For all electrical products, which are under my responsibility, potential suppliers in Russia were found, assessed and their technical proposals were together developed, assessed and coordinated. QMS/EHS audits of these suppliers were performed. For all detected non-conformities during audits corrective actions were developed and their elimination was checked.• The following internal LLC "RGT" procedures were developed/updated:- "Supplier audit" (including QMS and EHS Assessment checklists)- "Corrective action request"- "Supplier qualification"- "Supplier deviation request"- "Supplier pre-assessment check-list"

1) Organizing the work of department from "zero" (start-up);2) Staff recruitment, team creation;3) Control over planning and performing supplier assesment audits;4) Control over performing corrective action plans, approved after supplier assesment audits;5) Control over the supplier qualification process;6) Participation in negotiations with suppliers regarding quality requirements to the contracts;7) Organization of procedures development regarding supplier quality assurance sphere.

1) development of internal procedures2) performing first article inspection (FAI) on supplier production plants3) development of quality requirements to the contracts with different suppliers4) performing supplier audits (assesment and target audits)5) performing different quality requests from contractors

1) collecting statistics about all non-conformity notifications for different suppliers of the components2) performing Pareto analysis using this statistics and defining repetitive defect groups3) request for corrective actions for preventing appearing these defect groups again in the future from different suppliers (8D) and tracing implementation of these actions by suppliers4) regular business trips to supplier plants (discussing corrective actions, action plans for its implementation and checking of performing it)5) using Isikava diagram for finding root cause of repetitive defects and designing action plan for preventing appearing of these defects again in the future6) supporting of quality engineers, located on production plant of JSC "Sukhoi Civil Aircraft"7) performing first article inspection (FAI) on supplier production plants8) making and updating KPI of different suppliers (Pareto diagram for part numbers, Pareto diagram for defect types, etc)9) development of matrix for contract attachments, signed with suppliers, regarding quality requirements and after-sales support of the components10) performing supplier audits (assesment audits and target audits)

1) collecting and checking of all necessary documentation for signing the document which accepts that supplier can produce the parts with required quality (PSW) and quantity (AFF) during different projects (PPAP work);2) working with different quality incidents during the project stage, making quality alerts, reclamations and compensation files to suppliers;3) working with the supplier using 8D procedure and performing 8D audit;4) participating in process audits (audits of production process) and pre-production audits;5) participating in validation of the package for different parts;6) providing protection of the conveyor from defect parts (organizing of sorting operations, isolation defect parts, etc)I was responsible for the sector of body parts during the year, then I was responsible for the sector of interior parts.Achievements:• Launching the project Sandero Stepway• Launching the project of modified version of Sandero• Launching the projects Fluence and Megane• Participating in launching of the project Duster

1) accounting of laboratory gauge devices2) control of performing the schedule of checking gauge devices3) checking gauge devices (devices for measuring thickness, particle counters, etc) and making protocols for it4) performing air dust measurements5) preparing monthly reports of laboratory work6) work with the device for defect detection - endoscope7) performing thickness measurements.Achievements:• reducing the time of checking gauge devices, because of optimization the process of making protocols for checking gauge devices using specified electronic forms