 Coordinate the full cycle of servicing, maintenance, and repair of hydraulic, mechanical, and electrical component. Preparing and perform the Factory Acceptance Test (FAT) and Site Acceptance Test (SAT) Maintenance and operate the Flexi Pipe/Cable Laying equipment (Hub Drive, Under Roller and Modular Spooler. Performing the maintenance and operating of the various type of Tensioner. Handling the Decommissioning equipment (Diamond Wire Saw, Shear Cutter, Grabber, Chop Saw, Umbilical Winch and Chute)

Carry out the full cycle of servicing, maintenance and repair of hydraulic equipment, subseatooling, diesel engine and winch.Able to perform spooling of Umbilical Reeler for hydraulic equipment, Abrasive Water JetCutting system and umbilical for air and water system.Performing the Subsea Cutting Tools like Diamond Wire Saw, Chop Saw, Subsea Shears, andAbrasive Water Jet Cutting.Capable to service and maintenance Controlled Fluid Excavation equipment (Hydraulic PowerUnit, Trenching such as T4000, T8000 and R2000).Performing and servicing the deck ancillary equipment like Hydraulic Power Unit, HydraulicPower Pack, Air Compressor, LARS and overboard sheaves.

Services :Conduct delivery inspection of systems and equipment supplied by IHC production and report findings.Create an overall service report with findings and recommendation regarding the customer, IHC products and suppliers.Lead & monitoring the project at local vendor for Project from IHC Asia Pacific Engineering :Detail Engineering packages fit for production purposes based on specifications and information received from the client, within the given budget and before the given deadline.Checks the specification for any missing or unclear information regarding the budget time, projects and specification.Performs engineering activities such as 3D Modelling and 2D Drafting,Performs complete self-check before sends engineering deliverable to QC for internal checking.

➢ Contribute for the Piping Installation Project in Offshore.➢ Carried out ovality checking and pipe matching during production by using Pipe End Scan.➢ Collecting and checking of all pipe and measurement data, including photographic and paper record.➢ Sorting and matching pipes according to the data measurement during production. This enables the most round pipes to be allocated to the more critical areas of the pipeline.➢ Optimal, accurate and rapid measurement tool of pipe and dimensions along with CeverSort & CleverFit software analysis including pipe end to end fit-up and pipe sorting.➢ Calibrate Pipe End Scan required calibration blocks to be used for inspection.➢ Initial pre check the pipe condition for the abnormalities defect.

- To Contribute the Preventive and Corrective Maintenance Tasks in SystemAutomated Platform Systems, Mechanical Systems, Conversion Machinery,Propulsion and Auxiliary Fields for the Malaysia NAVY Scorpene Submarine.- Supervise the task performed by subcontractors in order to achieve customer requirement and satisfaction.- Management of spare parts, equipment and tools required for maintenance tasks which includes validating and purchasing the proper spare parts, equipment and tools.- Ensure all the mechanical equipment must be serviced l, repaired, abd tested according to the specification.- Troubleshooting and Analysis the Incoming Defect after Sea Outing.- Prepare the Preparation Task that related to Dismounting, Inspection,Remounting, Testing, Safety Locking and Pressure Test.- Specify the Maintenance Tasks to be Performed Onboard or In Workshop.- Performing the System Trial Onboard before Sea Trial.- Representative to Perform Trial at Sea upon Completion of MaintenancePeriod.

New Model Planning & Development :- Performing Engine Endurance Test at other country (Japan, Thailand & India).- Planning Engine Test for Each New Model Event.- Leading Activities for Engine & Transmission.- Design Change Notice Judgement for Early Detection Changes before Event.- Come out New Countermeasure Request Form (CRF) for Quality Improvement.- Confirmation & Verification on the Local Part contact at Engine.- Engine Assembly Process Confirmation thru Engine Test.- Monitoring Local Part Maturation at supplier before event coming.Mass Production Quality :- Chief Inspection Engineer for Overall Plant No.2 Line.- Achieving GDP Target in Daily Production.- Monitoring DPU (Defect Per Unit) Target for Each Month.- Performing Quality Issue Problems into the Complex Analysis.- Preventing Problems outflow by Analysis.- Understanding for the Overall Car Process from Single Part to CBU Condition.- Monitoring the Previous Action at Department Process.- Involving the Inspection & Tuning Jig at Welding Department.- Confirm & Verify the Assembly Process at Assembly Frame Department.Market Claims :- Promote the Countermeasure for the Prolong Cases at Market.- Propose CRF based on Market Claims.- Theme up 1 Items from Monthly Market Claims for every Quarter

Achievement :- Completely Industrial Training for 3 months (maintenance department 9 weeks and operation department 3 weeks).- Plant fully shut down contribution within 4 weeks.- Inspection the combustion chamber & turbine blade with authorized Engineer. - Completely learn about the Vibration and Thermograph and using the Infrared Thermograph CameraJob Descriptions:- Assist technician for daily maintenance- Maintenance the equipment depend on schedules plan- Maintenance and services of pump, motor, valve, pipe, heat exchanger, lubricants oil, etc.- Alignment and calibrate the water pump.- Monitoring the daily production & operation at control room.