Arunkumar R Email & Phone Number

Bangalore, India

Destination : Team leader - Supplier qualityCustomer handling : Signify (Philips) -China, Netherland,Mexico, Turkey. Supplier handling : China, Malaysia, turkey, Mexico & Europe. 1.Supplier New product development. 2.Supplier new product PPAP evaluation and development. 3.8D CAPA verification and correction from supplier to resolve customer failures. CAPA implementation effectiveness verification supplier line audit. 4.Supplier process audit - New product Pilot run vs Control plan walkthrough and 8D Corrective action effectiveness verification. 5.Advanced quality planning deliverables responsible for New products introduction. 6.PFMEA assessment audit. 7.Supplier process readiness verification and improvement action implementation before Pilot run for New products. 8.Condut Supplier Pilot run audit & close the gaps before mass production. 9.Product Reliability test verification for CTQ items10.KPI preparation for PPAP, 8D, NCR, Onsite audit and present with customer during monthly review. 11.Conducting supplier Kickoff meeting for PPAP, 8D & NCR. 12.ISO documents preparation & responsible to conduct internal audit. 13.Customer interaction weekly & Monthly to get technical clearance & understand requirements. 14.Conducting internal weekly review and convey the customer escalation & requirements with Team members.

India

Customer handled : Hyundai motor (India & russia,Viatnam) & Kia motor (India). 1.Leading supplier quality team for Incoming inspection (Head lamp & parking brake, outside mirror, Transmission gear system) sub assy parts. PCA driver board, LED assy module, bulb, projection, wiring, connector, actuator, sensor, tgs knob, mirror, lense & housing, reflector, heat sink etc. 2.Globale supplier handling to reduce incoming part rejection and improve product quality to achieve customer ppm. (Korea, china, German, viatnam) 3.Supplier process Audit4.Failure analysis customer, in-house & field failure product. 5.RCA& CAPA action followup with supplier for customer failure & inhouse, incoming failures.6.Supplier 8D action review with customer & approval. 7.ISIR review & approval for new products & tool changeschanges & EO changes. 8.4M change part verify & effectiveness monitor9.New product securing plan collect from supplier and effectiveness monitor. 10.Supplier performance rating preparation and improvement followup with supplier. 11.Responsible to conduct supplier monthly review meeting for top 5 least PPM supplier and CAPA followup to achieve DPPM target. 12.Conduting MRB meeting for incoming & assy line rejection decision making & 8D followup. 13.KPI updating and present with Management during monthly review. 14.CFT member for resolving customer chronic issues. 15.Verify & approve Debit note for supplier part rejections and followup with supplier for rejections approval.

Chennai Area, India

Customer handled : Nokia, Motoroal & black berrySupplier handled : China, Singapore, Malaysia & india, taiwan. 1.Responsible for Incoming issue related to electronics (SMD & THT) and mechanical (injection molding & metal) commodity's.2.Analyzing the failure parts as per specification and preparing the reports for Communicating with Supplier end for further improvement action.3.Verifying the CAPA(8D) Report when the supplier submitted the RCA for defective parts.4.Train the new quality inspectors for incoming material inspection and equipment's handling.5.Preparing the RMA reports for failure related parts & sending to the supplier.

Bangalore

1.Handling Supplier Quality Issues Related to the electrical & mechanical Components in Mfg lines.2. Initiating the Primary analysis for the failure part as per specification of Part and Preparing the Report for sending to the supplier.3.Co-ordinate with NPD Team during Product Pilot Runs.4.Inspect the components as per the parts spec to ensure right component usage.5.To Sending the defective samples to supplier for analysis purpose & preparing the documents.

Bangalore

1.Operating of machine. 2.Machine maintenance.3.PCB visual inspection for after assembling through hole and SMD.4.Machine related documents preparing.5.To solve the component insertion error problem.

Bachelor Of Technology - Btech, Electrical, Electronic And Communications Engineering Technology/Technician

Diploma, Electronics And Communication Engineering, 83%

High School, 55%