Brian Moretti Email & Phone Number

Halifax, Nova Scotia, Canada

Ottawa, Ontario, Canada

• Review and Manage Technical Requirements: Translate requirements into a matrix and continuously evaluate risk of non-compliance and generate action plans to gain compliance• Communicate Interface Specifications: Produce interface control documents specifying sizes, tolerances and other details associated with each interface (physical, electrical and signals)• Produce Technical Manuals and Other Documents: Generate manuals for installation, operation and maintenance as well as lists of spares, availability/reliability/maintainability analysis reports, and other customer required documents• Perform FMEA: Perform both functions and parts based FMEAs and determine compensating provisions to mitigate risk of equipment failure• Interface with Vendors and Customers: Discuss technical requirements and issues, generate actions and track issue status • Collaborate with all Engineering Disciplines: Extrapolate design details from each engineering group to create complete design specifications, and coordinate activities to meet customer deadlinesdatabases and failure data to simulate system failure using reliability modeling software• Specify preliminary equipment sizing: Define duct paths, mount locations, and initial sizes based on customer requirements and initial platform geometry• Calculate system performance: Calculate system pressure loss and generate flow curves based on different design cases• Develop new manufacturing procedures: Developed and qualified procedures for solution heat treating and laser label etching• Design test equipment fixtures: Use inputs from other engineers and test facilities to create models and drawings of fixtures used for shock and vibration testing• Perform drawing checks and approvals: Evaluate drawings against customer requirements, design inputs and drawing practices and sign when drawings are adequate• Translate requirements, vendor details and other source data into design specifications used for 3D modeling

Ottawa, Canada Area

-Coordinate, manage and observe ballistic testing for new and existing technologies-Provide engineering support to production via tool and template design, and other streamlining solutions-Design, analyze and derive parts/assemblies using 3D modeling software-Develop and break-out Bills of Materials (BOMs) and raw material requirements-Participate on the Material Review Board (MRB) to provide disposition on quarantined products and sub-components-Analyze products with reoccurring discrepancies to determine root cause of the defect and provide instructions to production to resolve issues-Assist quality assurance in determining acceptance/inspection criteria for various product lines-Communicate with each department to ensure their understanding of the technical information provided and to address any of their concerns-Perform statistical analysis across various manufacturing processes to develop tolerances and recommend process improvements-Submit change requests to project design authorities based on manufacturing and inspection requirements-Visit customer build sites to witness installation of product and troubleshoot issues-Represent company at industry trade shows to find new customers and develop business relations with existing customers

Russell, Ontario

-Create detailed 2D shop drawings using AutoCAD of custom millwork for both residential and commercial purposes. -Create sheet layouts of parts for ordering and cutting.-Contact suppliers to inquire about stock availability and pricing.-Submit purchase orders to suppliers and record material cost totals in Microsoft Excel.-Troubleshoot errors and clarify details for cabinet makers with regards to the shop drawings and project details.-Utilize Microsoft Excel to compile lists of materials required for projects and the associated costs to support the company budget and project pricing.-Analyze basic drawings from clients, designers and architects to produce accurate quotations.-Analyze log sheets from cabinet makers to seek out problem areas, improve project budgets and provide project leads with time allowances for tasks.-Appointed Safety Representative. Report hazards observed and make suggestions to improve heath and safety. -Currently researching new cabinet software and automated manufacturing equipment to determine the most effective solutions for our business.

Toronto, Canada Area

-Collaborated to design, build and race a formula one car.-Designed and installed an automatic shifting system and RPM controlled air intake.-Programmed microcontrollers in C referencing registers and bit addresses.-Prototyped a circuit to integrate the microcontroller signals with the mechanical system.

-Worked in a team of three to investigate the mechanical properties of cartilage.-Researched articles pertaining to articular cartilage and current medical applications of materials for cartilage repair.-Developed a mathematical model of articular cartilage in tension and compression.-Produced a report of our research and modeling.-Presented a PowerPoint presentation highlighting the key findings of our research.

Toronto, Canada Area

-Worked in a team of five to design and build a motorized projectile toy with optimized specifications.-Lead the analysis of our concept. Listed all of its subsystems and parts to determine the key factors that control its performance.-Analyzed the key factors further to determine possible sources of failure and their effect on the performance of the design.-Tested our prototype in multiple configurations to determine the optimal settings of its key components, including accuracy of the projectile mechanism and the motor function.

Toronto, Canada Area

-Worked in a team of four to design and build a 2D plotter including programming, electronic and mechanical subsystems.-Headed the electronic portion of the project. Built and adjusted circuits using relays, switches and amplifiers to integrate the mechanical parts of our system with the microprocessor.-Developed design concepts for the mechanical portions of the plotter and analyzed them to find potential failure points.-Manually machined and joined parts with precision.

Toronto, Canada Area

-Worked in a team of four to research the mechanisms responsible for lower back pain related to manual lifting.-Appointed project coordinator. Divided tasks and monitored progress to ensure on-time completion of the project.-Created a formal research proposal with a detailed project plan.-Created a model of the human body to calculate the stress created on the lower back.-Presented a PowerPoint presentation regarding proper lifting techniques with evidence to support our recommendations.

-Coordinated a team of 18 members to build a modular system comprised of a vehicle moving through 5 separate stations before being launched.-Responsible for creating parts and subsystems to integrate each station together seamlessly. Designed and built tracks, vehicle support platforms and a vehicle storage unit.-Assisted with design of the stations to ensure effective integration with our prototypes.-Placed first in a competition against other teams with similar mechanisms.

-Worked in a team of four to research multiple methods of power generation and determine the optimal solution for Ontario Power Generation (OPG).-Researched the performance, environmental impact and operation costs of a nuclear facility to compare against other power generation methods studied by team members.-Analyzed and processed the data from each team member to compare quantities from each power generation method on an equal level.-Created a report highlighting key data requested by both OPG and our professor.-Presented a PowerPoint summary of our report, including recommendations to OPG with supporting numerical evidence.