Marc Norton Email & Phone Number

Middlesbrough, GB

Immingham, England, United Kingdom

Conoco: Phillips 66 – Refinery: Siemens (Nov 24 – Present)Model K601-TuW-2 SST (Siemens Steam Turbine) Full overhaul currently underway to document the extent of fire damage from a previous incident. To produce a detailed report of the damage & to advise the customer with an efficient, cost effective way off getting the equipment back online.

Ferrybridge, England, United Kingdom

Enfinium: Ferry Bridge - Power Station, Outage: Siemens (Oct 24 – Present)Conducted extensive inspections to meet specific requirements of the Siemens Steam Turbine SST 800's reliability centered maintenance (RCM) Program. Replacements sourced & repairs actioned on critical components to address wear & corrosion. Alignment & clearance tolerances met to.

Shearwater Shell

Overhaul & Maintenance Rotating Scopes:08 MV 3A – LP Compressor – Dry Gas Seal Exchange06-02 MV 7B – Flash Gas Compressor – Bundle ExchangeSolar Mars Turbine – 8k Service & Engine Exchange

Aberdeen, Scotland, United Kingdom

-Main scope included decommissioning gas compressors which were to be sent onshore for overhaul. I took ownership for the quality delivery, ensuring that all client specifications were met by using a detailed and systematic process to ensure safety, environmental protection, and compliance with regulatory standards. -Initial assessment carried out to.

Aberdeen, United Kingdom

-Carrying out corrective maintenance on various rotating equipment, I.C engines, compressors, pumps, gearboxes, diesel centrifuge separators, heat exchangers, fire water pumps & lifeboats, etc. -Complex EX11: Competent to carry out mechanical duties: Preparation, installation, inspection & maintenance in hazardous locations where gases, vapors or dusts can.

North Tees / Hydrogen Plant

-Commissioned various mechanical plant and instrument pipework systems.-Carried out condition-based monitoring including: Vibration analysis and temperature tests.-Valve integrity checks with an advanced understanding of P & I.D, piping/structural isometrics & PFD drawings.-Complying work-packs in line with commissioning procedures.-Creating permits & risk.

Netherlands

-Carried out function testing & fault-finding analysis on various hydraulic & pneumatic systems in accordance with client’s standards & procedures.-Hydrostatic testing.-Carries out corrective maintenance on various plant, pumps, motors, gearboxes, etc with limited Supervision.-Used red-lining methods to highlight modifications while keeping all.

Southern North Sea

-Logged daily fault reports, highlighted & rectified any punch-list items, ensured that various plant was mechanically complete and ready for functional testing.-Updated ITR (inspection test records) accordingly to ensure HCP (hand-over completion packs) were delivered to the client on schedule.-Leak testing (HeN)

North Sea

-Alignment of plant & pipework, with tolerances to be within 0.02mm.-Carried out water treatment, chemical injection flushing, lube oil flushing of various systems.-Routine change out of various filters, membranes, oils & coolants.

K14-FA-1 NAM

-Shutdown maintenance involved the use of controlled procedures such as purging, flushing & draining of vessels/pipelines.-Ensured LEL readings were at a safe level before isolations could be implemented allowing for maintenance work & valve replacement.

Leman Bravo

-Removal of redundant plant & pipelines using hydraulic torque/tensioning equipment and oxy-acetylene cutting equipment.

Sole Pit Clipper

-Directly involved with general mechanical upgrades on the compressors & generators. -Assisted in the removal of redundant crane followed by the installation and testing of replacement crane.-Displayed Millwright, piping & workshop knowledge.

Leman Bravo

Assisted in the removal of the redundant crane followed by the installation and testing of replacement crane.

Leman Charlie, The North Sea (UK)

Assisted Completions Engineer, using schematic drawings and system P&ID’s to punch list Items on Instrument systems. Responsible for issuing permits and giving toolbox talks, ensuring all members of the team are fully aware of their roles and responsibilities. Assigned tasks to specific members of the team to ensure the job ran safely and efficiently.

Corus Steel Making Plant

Corus Steel Making Plant: General mechanical work included but was not limited to maintaining/replacing old valves, motors, pumps, rollers, and shafts.

Teeside

Ensco 72 Platform: Installed, tested and commissioned commercial plumbing and air conditioning units on the accommodation block of the jack-up barge.

Solstad: Normand Tonjer Douglas

I carried out general maintenance work to plant and pipework.Installed pipelines and realigned various shafts and motors. Dressed pipework for welders and carrying out basic rigging, slinging & fire watching duties.

West Auckland

Installed pressurised water cylinders & air-cooling units to WRAS Regulation Standards. Followed system diagrams and company CNR. I also installed instrument pipe work to stats, gauges, and pressure differential valves with the use of isometric drawings and P&I.D's.

Redcar Blast Furnace

Replaced 2 tonne valve bodies, dressed up flange faces followed by the installation of pipe-work, motors, valves and rollers.

Hartlepool College

With the use of MEWP (mobile, elevating, work, platforms) scissor lifts and cherry pickers I installed mepla pipework. This had to be hydraulically crimped or fused to withstand very high pressures. I also installed large solar panels.

Leman (Yorkshire)

Installation of refrigeration & air cooling units in a food preparation factory, followed by the commissioning of the system.

North-East (UK)

Time served 4 years apprenticeship.NVQ Level 3 in Mechanical Engineering at Hartlepool College of Further Education (2003 – 2007).I attended college on a day release basis spending the reminder of the week on various sites and plants.

Hnd In Mechanical Engineering, Mechanical Engineering Related Technologies/Technicians, Distinction

Hnc: Higher National Certificate, Mechanical Engineering, Distinction

Activities and Societies: PROFESSIONAL QUALIFICATIONS HNC in Mechanical Engineering - Teesside University School of Science & Engineering.

Nvq Level 3, Mechanical Engineering, Level 3

10 Gcses, Maths, English, Science