• Responsible for Complete Diesel Generator sets (up to 500 KVA) troubleshooting, controller upgrade, fuel monitoring system, and software diagnostics• Installation, commissioning, testing & troubleshooting of Temporary construction Power Stations with DG sets, ATSs, and Starter Panels• Installation, commissioning of instruments like Flow meters, Level Sensors, Fuel Sensors, Pressure Transducers, Temperature sensor and switch etc. and their integration with PLC system.• Worked on These Engines and its Software of Volvo, Perkins Kubota, caterpillar,• Fabrication of Distribution Board, Sub Distribution panel Board, SCADA Panel Board, Motor starter Panel -DOL, STAR DELTA, SOFT STARTER, VFD Board• Telemetry data analyzing, communicating, report compilation, command service crew for attending callout• Maintain and take all utility, electrical power reading makes report and file them for further record keeping• Do maintenance of utility & plant machinery as below.• Worked on Action Remote Management Platforms • Repair & installation of pumps such as Borehole, Sump, Sewage, centrifugal pump• Monitoring and controlling the panel and generators• Programming PLC, HMI, Deep Sea Engine controller and MMC (Motor Management Controller)• Pre-Commissioning and commissioning of electrical items such as: motors, starter panels, ATSs, DBs, RTU panels, telemetry devices.

As a ship repair Electrical Engineer, Trouble shooting and repair DOL starter, Star Delta starter and distribution panel etc.Complete installation Blast water treatment system(BWTS), cable tray, cable laying, Looping test, Termination and runWell knowledge, overhaul and rectify the issue in Alternator(Up to 1100KVA), Shaft Generator(Upto 800KVA, Bow thruster motor(Upto 800 KW) Working on Limit switch, Temperature switch, Pressure switch, Level sensor, Pressure sensor, Hydrogen sensor, Flow switch, Flow meter and Actuator ETCAlternator check and AVR trouble shooting.Trouble shooting and tried out of Programmable logical control panelsTeam management and team leadingCoordinating with internal departments on allocated jobs for completion as per scope schedulePreparation of risk assessment and checklist for assigned job scopeControl cost of job by tracking men hours, Material and vendorsBlast water treatment system installation, Cable pulling, Loop check, Termination and commissioningInduction Motor installation, troubleshooting, overhaul and their PPMWorked on Generator Alternator overhauling up to 2000 KVADG set repair and AVR trouble shootingTrouble shooting and tried out of Programmable logical control panels and Programmed Omron. SchneiderWorking on Limit switch, Temperature switch, Pressure switch, Level sensor, Pressure sensor, Hydrogen sensor, Flow switch, Flow meter and Actuator ETCTrouble shooting and repair DOL starter, Star Delta, soft starter and distribution panel etc.Dealing with controllers, display units- their configuration, connection and troubleshootingElectrical Team management, team leading, dealing with vendor repair of Marine Automation system.Coordinating with internal departments on allocated jobs for completion as per scope schedulePreparation of risk assessment and checklist for assigned job scope Control cost of job by tracking manhours, Material and vendors dealing

Experienced Electrical and Automation Engineer with demonstration of working in Electrical and electronics, Fabrication of Distribution Board, Sub Distribution panel Board ,SCADA Panel Board, Motor starter Panel Board Telemtry data analysing, communicating, report compilation, command service crew for attending callout Maintain and take all utility, electrical power reading make report and file them for further record keeping Pre-Commissioning and commissioning of electrical items such as: motors, starter panels, ATSs, DBs, SPBs, telemetry devices.Monitoring and controlling the panel and generatorsProgramming PLC, HMI, Mobicon, Deep see Engine controller and MMCknowledge in Induction motor and Centrifugal submersible pumpsDo maintenance of utility & plant machinery as below.Worked on Action Remote Manegement Platform,SQL etc.

• Troubleshooting of packaging machine• Installation of Packaging machine.• Maintenance semi automatic strapping machine.• Trouble shooting Automatic strapping machine based on PLC• Continuous band sealer.• Inspection of the loops (check loop)• Instrumentation installation.• Planning and preparation of work.

• Operating of electrical devices like solenoid valve ,motorized valve ,float switch, electro magnetic sensor, flow meter• Complete daily inspections of all Electrical equipment.• Work on site with all safety rules.• Working area clean and good housekeeping