Michael Malabanan Email & Phone Number

Australia

1. Perform Proof load on range of Lifting and Lifted equipment’s using certified weights, test bed pulling machine, Pad Eye hydraulic tester, water bag and Load cell.2. Perform non-destructive inspection. Utilize Magnetic Particle Test (MT), Penetrant testing (PT) on lifted equipment’s, welded fabrication or existing structure, casting and wrought products for ndt inspection as per customer request to applicable test specifications.3. Perform Certified Visual inspections on Existing Rigging & Lifted Equipment as per applicable Australian Standards. 4. Assemble and manufacture of lifting gears from Chain slings, wire rope slings and Fiber rope splicing. wire rope termination such as machine swage, Flemish swage, thimble eye, soft eye and socketing wire termination.5. Conduct offshore Mooring inspection of Anchor wire and Chain which also includes non-destructive testing (NDT) Inspection on offshore jewelries. 6. Operate test bed for proof load and destructive test of wire ropes and chains.7. Prepares and signed certificates for rigging visual inspection, proof load, and Non-destructive Inspection.

Perth, Western Australia, Australia

1. Perform Proof load on range of Lifting and Lifted equipment’s using certified weights, test bed pulling machine, Pad Eye hydraulic tester, water bag and Load cell.2. Perform non-destructive inspection. Utilize Magnetic Particle Test (MT), Penetrant testing (PT) on lifted equipment’s, welded fabrication or existing structure, casting and wrought products for ndt inspection as per customer request to applicable test specifications.3. Perform Certified Visual inspections on Existing Rigging & Lifted Equipment as per applicable Australian Standards. 4. Assemble and manufacture of lifting gears from Chain slings, wire rope slings and Fiber rope splicing. wire rope termination such as machine swage, Flemish swage, thimble eye, soft eye and socketing wire termination.5. Conduct offshore Mooring inspection of Anchor wire and Chain which also includes non-destructive testing (NDT) Inspection on offshore jewelries. 6. Operate test bed for proof load and destructive test of wire ropes and chains.7. Prepares and signed certificates for rigging visual inspection, proof load, and Non-destructive Inspection.

Al Khobar Saudi Arabia

Main function is to control the visual and Dimensional check points during the course of rolling of the Spiral and Longitudinal welded pipes produced. Visual inspection is distributed to Three (3) Visual Stations.Primary Station- is responsible for the issuance of Qc card to facilitate process flow of pipes and control visual and dimensional tolerances.Re-check station- Visual re –examination of pipe condition after repair.Final Inspection- Re-examination to assure that the quality of the finished product meets the requirements of Visual and Dimensional inspection.Daily checking of inspection devices every first hour of the shift.100% outside circumference and pipe length checking.Inform Pipe Making Station of any quality problem observed during rolling.Conduct Magnetic Particle Test (MT), fluorescent Wet and Visible Wet continuous method for suspected areas in Hot Rolled Coil, steel plates, repair portion, pipe bevel and pipe ends for occurrence of lamination or cracks. Also conduct Residual Magnetism after MT.Conduct Normal beam Ultrasonic scanning (UT) for Pipe ends lamination checking.Conduct penetrant test (PT) on pipes and plates with suspected defects open to the surface such as scabs or crack.Issue Notice of Non-conforming Product (NNP) for pipes which do not conform with the prevailing standards.UT INSPECTOR (UT-II)Conduct manual Ultrasonic test (UT) of all T-cross pipes and normal pipes with excessive markings detected flaws from auto line UT for verification at Re-check Station. Manual Ultrasonic testing of coil top and bottom using normal probe for scab line and lamination before coil or plate be rolled at Pipe Making Station.Conduct calibration of Ultrasonic Testing Equipment USM 35X using STB – A1 V1 block and Miniature Blocks V2 block.Conduct manual ultrasonic test of stored pipes at the yard for verification of suspected hydrogen delayed cracking (HDC) after 72 hours.

Al Khobar Saudi Arabia

1. Main function is to control the Visual and Dimensional check points in three (3) Inspection stations, Primary Station, Re-Checked Station and Final Station during the course of rolling of Spiral and Longitudinal SAW pipes produced according to standards as per Inspection Data for sour and non-sour pipe APL 5L 44th edition.2. Visually check (VT) the inside and outside welds of the pipe and parent metal for surfaces discontinuities. 3. Conduct Magnetic Particle Test (MT), fluorescent Wet and Visible Wet continuous method for suspected areas in Hot Rolled Coil, steel plates, repair portion, pipe bevel and pipe ends for occurrence of lamination or cracks. Also conduct Residual Magnetism after MT.4. Conduct Normal beam Ultrasonic scanning (UT) for Pipe ends lamination checking.5. Conduct penetrant test (PT) on pipes and plates with suspected defects open to the surface such as scabs or crack.6. Issue Notice of Non-conforming Product (NNP) for pipes which do not conform with the prevailing standards.7. Conduct calibration of Ultrasonic Testing Equipment USM 35X using STB – A1 V1 block and Miniature Blocks V2 block.8. Conduct manual Ultrasonic test (UT) of all T-cross pipes and normal pipes with excessive markings from auto line UT using 45o, 60o, and 70o degrees angle probes, and check the location of defect as per requested by the welder.9. Manual Ultrasonic testing of coil top and bottom using 45o degrees angle probe for scab line and straight or normal probe for lamination.10. Conduct manual ultrasonic test of stored pipes at the yard for verification of suspected hydrogen delayed cracking (HDC) after 72 hours in storing to ensure the quality of pipes before delivery.

1. Machine operation, troubleshooting and repair of Vertical Treater machine use in the production of Prepreg and Laminates the based material of PCB.2. Daily monitoring and inspection of machine parameters and settings that might affect the quality product.3. Actively involved in safety and preventive maintenance.4. Daily checking of production order to be mass-produce and counter checking it from SAP system.5. Employ SAP system for confirmation of finished production orders.

Fpip Batino Calamba City, Laguna

1. Prepare preventive maintenance schedule of machines, trouble shooting, overhaul and repair.2. Manage and control spare parts, request quotations and drawing of parts by means of AutoCAD for fabrication which are not standard parts.3. Check daily utility status; Organize and schedule repair jobs for all department utility problems.4. Report machine associated problems and official communication to Japan and Singapore customer service for Ulvac Sintering Machine.5. Actively involved in machine improvements and modification of department activity.6. Actively involved in Total productive maintenance (TPM).7. Manage bulk delivery order of Liquid nitrogen and Argon gas.8. Published Instruction manual for Hitachi vertical powder pressed machine.9. Reduction of tantalum powder material consumption used in capacitor production through seminar on SIX SIGMA green belt project.