Patrick Cochrane Email & Phone Number

Calgary, Ab, Ca

Ft Mcmurray Area

Calgary, Canada Area

Calgary, Canada Area

• Solved field piping issues through RFI submittals, FCN’s and field level discussions with the client’s on site engineering team.• Provided the cost engineering team with FCN submittal information for cost tracking.• Created redline and asbuilt drawings for QC and construction activities.• Answered specification, technical and material compliance related questions from the superintendents, General foremen and field personnel.• I monitored the safety of all construction activities, making on-site personnel safety the top priority.• I followed up RFI submissions to ensure field had the updated and correct information to complete the scope of work.• I educated Craft/Trade personnel on the quality standards throughout the construction process.

Kearl Lake Oil Sands / Shell Scotford Ft Sask Ab/ Co-Op Refinery Regina Sk

• Completed daily safety audits on craft providing positive feedback as well as identifying and documenting areas for improvement.• Participated in daily safety walks to ensure company safety standards and policies were being followed.• Participated in and assisted area superintendents with the weekly site wide safety meetings and documented all employee concerns for immediate rectification by superintendents.• Facilitated the processing of RFI’s by performing field investigations and gathering all information required to support the request.• Entered RFI’s into Company and Client document log for tracking and record keeping.• Followed up RFI submissions to ensure field had the updated and correct information to complete the scope of work.• Educated Craft/Trade personnel on the quality standards throughout the construction process.• Managed a team of fourteen on-site walk-down/punch-list inspectors for 9 months.• Assigned projects and tasks to employees based on their competencies and specialties.• Coordinated and performed Hydrotest pre-inspections and post-hydro audits.• Reviewed and ordered material for Field Change Notices (FCN’s).• Acted as a liaison between the general contractors and Construction management Team.• Submitted all project closeout documents in accordance with the contract to turnover group.• Accurately provided status information on project progress to the project progressing team.• Created Fieldwork packages for the Piping group.• Produced material takeoffs from field construction work packages and followed up on deliveries of material to site.• Created all torque and tensioning sheets and submitted them to the turnover group.• Acted as a liaison with company safety representatives to promote awareness and understanding of safety protocols.• Coordinated training for the Walk-down/Punch-list team on site-specific requirements, techniques and procedures

Calgary, Canada Area And Various Sites In Bc And Alberta

• I created Plot Plans based on either the Engineer’s or my own design.• Created Process Flow Diagrams (PFD’s) with information provided by the Process Engineering Group.• Created Piping and Instrumentation Diagrams (P&ID’s) with information provided by the Process Engineering Group.• Created Mechanical Flow Diagrams (MFD’s) with information from the Process Engineering Group.• Created General Arrangements based on the Plot Plan, P&ID’s and Line lists.• Created Isometric Drawings (ISO’s) based on information from the General Arrangement Drawings and P&ID’s• Created Cut Sheets based on the Isometric drawings with consideration given to shipping size/weight, ease of installation, field weld positioning and access to the weld locations.• Created Pipeline right of way drawings (ROW’s)• Created Pipeline crossing details• Created Line lists.• Lead a 5-person team of designers responsible for as-building Encana sites.• I monitored the safety of all company personnel under my supervision on sour and sweet brownfield sites.• Extensive Gas plant as-building and punch-out experience.• Extensive Compressor Station as-building and punch-out experience.

Shell Orion Cold Lake Ab

• Field Tech/Process Piping Designer responsible for producing all as-built mark-ups and field sketches and submitted them to the EPCM for turnover.• Created drawings and field sketches for all new field run lines added.• Performed all piping walk-downs.• Created punch lists and assigned deficiencies to the appropriate crews for completion.• Confirmed all deficiencies were completed and signed off packages for turnover.• Ensured specification adherence of all piping material, valves and inline instrumentation.• Ensured correct blinding, bolting and gasket materials were installed.• Ensured installation of correct supports/guides/anchors.• Confirmed permanent spacers and spec blinds were installed and set to correct position.• Performed pre hydro punch-out and witnessed tests.• Ensured all instruments and pressure sensitive equipment was removed from test and jumpers were installed.• Ensured all high and low point vents were installed including bleed blinds.• Ensured flow direction of valves and inline instruments was correct• Ensured removal of check valve internals or pulled valve for test.• Ensured an appropriate area was flagged off for safety• Ensured all field personnel were aware of test being performed and instructed not to enter flagged off area.

Calgary Head Office And Various Field Sites In Alberta And Saskatchewan

• I created Plot Plans based on either the Engineer’s or my own design.• Created Process Flow Diagrams (PFD’s) with information provided by the Process Engineering Group.• Created Piping and Instrumentation Diagrams (P&ID’s) with information provided by the Process Engineering Group.• Created Mechanical Flow Diagrams (MFD’s) with information from the Process Engineering Group.• Created General Arrangements based on the Plot Plan, P&ID’s and Line lists.• Created Isometric Drawings (ISO’s) based on information from the General Arrangement Drawings and P&ID’s• Created Cut Sheets based on the Isometric drawings with consideration given to shipping size/weight, ease of installation, field weld positioning and access to the weld locations.• Created Pipeline right of way drawings (ROW’s)• Created Pipeline crossing details• Created Line lists.• Lead a 5-person team of designers responsible for as-building Encana sites.• I monitored the safety of all company personnel under my supervision on sour and sweet brownfield sites.• Extensive Gas plant as-building and punch-out experience.• Extensive Compressor Station as-building and punch-out experience.

• I created Plot Plans based on either the Engineer’s or my own design.• Created Process Flow Diagrams (PFD’s) with information provided by the Process Engineering Group.• Created Piping and Instrumentation Diagrams (P&ID’s) with information provided by the Process Engineering Group.• Created Mechanical Flow Diagrams (MFD’s) with information from the Process Engineering Group.• Created General Arrangements based on the Plot Plan, P&ID’s and Line lists.• Created Isometric Drawings (ISO’s) based on information from the General Arrangement Drawings and P&ID’s• Created Pipeline right of way drawings (ROW’s)• Created Pipeline crossing details• Created Line lists.

Red Seal Steamfitter, Steamfitting / Pipefitting, 93%

Cadworx, 3D Piping Design, Certificate

Hands on 3D piping design course

Ppd, Process Piping Design, 3.8

Process Piping Design

Red Seal Plumber / Gasfitter, Plumber / Gasfitter, 87%

Process Piping Design